Question about 1992 Chrysler New Yorker

Open Question

How to replace a 92 chrysler new yorkers ignition switch.. is it a hard job or pretty simple?

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 840 Answers

SOURCE: belt diagrams for a chrysler new yorker

call a chrysler dealer and they can fax you a copy of the diagrams that you need

Posted on Jan 24, 2009

Ad
  • 20 Answers

SOURCE: Can't find flasher for blinkers on a 92 Chrysler New Yorker.

they should be on top of the steering column

Posted on May 27, 2009

  • 32 Answers

SOURCE: '92 chrysler new yorker salon is stalling after

Bad fuel pump,have the presure checked,turn the key on,wait 10 seconds,and see if stays running longer,if it does,its your fuel pump.have it changed.First,change your fuel filter.

Posted on Jul 26, 2009

  • 192 Answers

SOURCE: how to set the timing on a 1995 chrysler new yorker

There is no way to set the timing on this vehicle. Everything is computer controlled. The timing is controlled by readings from a combination sensors on the engine. The main sensor responsible for the timing is the CAM Position Sensor. This isn't the only sensor, just the main one. It is found on the top front of the engine, right near the coolant thermostat housing.

Posted on Nov 14, 2009

jturcotte
  • 8572 Answers

SOURCE: need a diagram for tensioner/idler

Please let me know if you have any questions, and thanks for using FixYa.
3.3L AND 3.8L ENGINES-SERPENTINE BELT

See Figure 12
The Poly-V drive belt is provided with a dynamic tensioner to maintain proper belt tension. To remove or install this belt:

  1. Raise the front of the vehicle and safely support on jackstands.
  2. Remove the right front splash shield.
  3. Release tension of the belt by rotating the tensioner assembly clockwise.
  4. While holding the tensioner in the rotated position, remove the belt from the various pulleys-make sure to note the route that the belt takes before removal.
  5. To install the belt, route it through the various pulleys except for the tensioner pulley. Once the belt is satisfactorily mounted on the pulleys, rotate the tensioner clockwise and slide the belt onto the tensioner pulley. Make certain that the belt is mounted so that the grooves in the belt are correctly aligned with the grooves in the pulleys.
jturcotte_1511.gif

Fig. Fig. 12: To remove the serpentine belt from the 3.3L and 3.8L engines, rotate the tensioner assembly clockwise

  1. Install the right front splash shield to the underside of the vehicle.
  2. Lower the vehicle back to the ground.
  3. Start the engine and allow to idle for a few minutes. Shut the engine off and double check the placement of the belt on the pulleys.

Posted on Apr 09, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Need to know where to buy 92 driver side window regular for new yorker


Lots of suppliers for aftermarket on line, but go to a chrysler dealer and check price there as well. Sometimes Chrysler/Dodge parts are reasonably priced.

Feb 09, 2014 | 1992 Chrysler New Yorker

1 Answer

92 chrysler new yorker, how do you take off the hubcaps?


take the center off of rim-a piece about 5" in diameter, then you need a special tool to take the nut loose in the middle

Nov 10, 2013 | 1988 Chrysler New Yorker

1 Answer

Where is the fuel cutoff switch on a 92 Chrysler New Yorker Fifth Avenue


Hi Big bang, Is your vehicle a diesel? If it's petrol injection the fuel cut off is not a separate switch. When you turn off the engine you also turn off the power to the injectors and therefore cut the fuel feed. If the engine is dieseling after turning off, I believe you have a problem with a leaking injector. This will also become evident when starting as the engine will take longer to fire, as it will have lost fuel rail pressure. Regards John

Apr 25, 2012 | Chrysler New Yorker Cars & Trucks

1 Answer

Where is the location of the obd 1 port on a 92 chrysler new yorker


It is under the hood near the computer, driver side fender near the battery.

Apr 10, 2011 | 1992 Chrysler New Yorker

1 Answer

I dont know where my fuel pump is


looked it up online, says that for 1992 new yorker it's in the fuel tank. wouldn't swear that the resource i use is 100% reliable, but have only found a few cases where it was wrong. hope that helps

Jun 17, 2009 | 1992 Chrysler New Yorker

Not finding what you are looking for?
1992 Chrysler New Yorker Logo

Related Topics:

135 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8567 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...