Question about 1998 Dodge Durango

Open Question

I have a 1998 Dodge Durango I need to replace the water pump bypass hose I need to find the quickest most accurate way

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I just changed the thermostat in my 2000 dodge Durango and its leaking more water now than it did before I replaced. What could be the problem?


Dodge Dakota Coolant Leak Repair - Including Bypass ...

? 24:00
www.youtube.com/watch?v=3lhfurJVzcM
Aug 11, 2012 - Uploaded by mreinsmith Dodge Dakota Coolant Leak Repair - Including Bypass Hose, ....yup my 2000Dakota had I leaking bypass I put in New water pump thinking ..... Dodge Durango 4.7 coolant, thermostat, and auxiliary water pump replacement.

Feb 26, 2015 | 2000 Dodge Durango

1 Answer

1998 Dodge Durango heater hose


The metal section is part of the water pump. You can just replace the rubber section of hose.

Nov 01, 2011 | Cars & Trucks

1 Answer

My 1998 dodge neoni have bypassed the heater core put on a new radiator new sensors but my caer is still running hjot the mexhanic said that my water pump was goo? wat do u think?


Sounds like the thermastat or the water pump id about right. You could also have a collapsed hose, Can check this by squezzing the hoses and see if soft. If so i would replace . good luck to you.

Mar 31, 2011 | 1998 Dodge Neon

1 Answer

Replaced the thermostat and water pump in my 1998 Dodge Durango and flushed the cooling system but it still won't blow heat. What's the next thing to try?


Check the two hoses going to the heater core.
They will be in the engine compartment on the passenger side fire wall.
Touch both hoses. There should be only about 15 deg. difference between the two of them
If one is hot and the other is cool then the heater core has failed and needs to be replaced.
Hope this helps give feedback thank you FixYa.

Feb 05, 2011 | 1998 Dodge Durango

1 Answer

Need to replace water pump on a 2000 Dodge Durango. Would like any details on how to to it.


3.9L, 4.7L, 5.2L, 5.9L, 8.0L Gasoline Engines
  1. Carry out the "Common Steps" above.
  2. Remove the upper radiator hose.
  3. Remove the fan and shroud assembly.
  4. On engines except 4.7L, remove the four water pump pulley bolts and remove the pulley.
  5. Remove the heater hose pipe mounting bolt, if fitted.
  6. On engines except 4.7L, loosen the bypass hose clamp at the water pump.
  7. Remove the seven water pump mounting bolts and, on the 4.7L, one nut.
WARNING Bolts may be of different lengths. Be sure to note their locations.
To install:
  1. Reverse the removal procedure.
  2. The 8.0L engine uses an O-ring to seal. Use a new one and lubricate it with petroleum jelly before installation of the pump. Also, use sealant on the threads of the heater hose pipe, position the pipe as shown before installing the pump and tighten the nut to 12 ft. lbs. (16 Nm).
  3. On pushrod engines, connect the bypass hose to the pump while installing it.
  4. Tighten the bolts to 30 ft. lbs. (40 Nm) on pushrod engines, 40 ft. lbs. (54 Nm) on the 4.7L engine.
  5. Spin pump to ensure the impeller is not rubbing against the timing chain case.
  6. When installing the heater hose pipe, ensure that the slot in the pipe bracket is bearing against the mounting bolt. This will hold the pipe in as far as possible to prevent leaks.
  7. Tighten pulley bolts to 20 ft. lbs. (27 Nm) on V-6 and V-8, 16 ft. lbs. (22 Nm) on the V-10.

zjlimited_368.jpg

Fig. Water pump bolts differ in length; note check location before installation-3.9L, 5.2L, and 5.9L gasoline engine shown

Hope helps (remember to rate this answer).

Dec 30, 2010 | 2000 Dodge Durango

1 Answer

Need to replace the water pump . Looking for direction


  1. Drain the cooling system.
  2. Remove the accessory drive belt.
  3. Remove the lower radiator hose.
  4. Disconnect the heater hose from the pump, if fitted.
  5. Always use a new gasket when installing the water pump. Clean mating surfaces thoroughly before installation.
  6. Check the accessory belt routing against the plate in the engine compartment before starting engine.
  7. Allow the engine to reach operating temperature and check for leaks.
  8. 3.9L, 4.7L, 5.2L, 5.9L, 8.0L Gasoline Engines Remove the upper radiator hose. Remove the fan and shroud assembly. On engines except 4.7L, remove the four water pump pulley bolts and remove the pulley. Remove the heater hose pipe mounting bolt, if fitted. On engines except 4.7L, loosen the bypass hose clamp at the water pump. Remove the seven water pump mounting bolts and, on the 4.7L, one nut.To install: Reverse the removal procedure.

Dec 21, 2010 | 1998 Dodge Durango

1 Answer

How do you put a water pump i a 1999 dodge durango 5.2 8cyc 4wd. if can step by step and a


First disconnectthe cable from negative terminal of the battery. drain the cooling system if the coolant is relatively new or in good condition, save it. remove the cooling fan and shroud. remove the drive belt and water pump pulley. loosen the clamps and detach the hoses from the water pump. if stuck try to twist to break seal. check hoses if bad replace. on v6 & v8 remove the water pump coolant return tube mounting bolt. Remove the bolts and detach the water pump from the engine. Note: the location of the various lengths and different types of bolts as you remove them. to ensure correct installation. on v8 models reach above the water pump with pilers to release the hose clamp on the bypass hose.clean the bolt & and the threaded hoses in the engine. compare the new pump with the old one make sure there identical. remove all traces of old gasket material from engine.

Sep 02, 2010 | 1999 Dodge Durango

1 Answer

How do you replace the water pump bypass hose on a 2001 dodge durango 5.9ltr?


I,m assuming you mean the metal part of the bypass hose. Looking at water pump drivers side is a small metal tube hooked to heater hose. The tube is bolted through a alum bracket. Remove bolt and pull tube out. May need to spray with penetrating oil as these corrode, and are stubborn Make sure vehicle is not hot. No need to drain coolant as it will come out of bypass hole. have drain bucket ready. Do not reuse o- ring as it will leak.

Jul 05, 2010 | 2001 Dodge Durango

1 Answer

How to install a water pump on 99 durango


  1. Clean gasket mating surfaces.
  2. Using a new gasket, install water pump to engine as follows: Guide water pump nipple into bypass hose as pump is being installed. Install water pump bolts Tighten water pump mounting bolts to 40 N·m (30 ft. lbs.) torque.
  3. Position bypass hose clamp to bypass hose.
  4. Spin water pump to be sure that pump impeller does not rub against timing chain case/cover.
  5. Install a new O-ring to the heater hose coolant return tube Coat the new O-ring with antifreeze before installation.
  6. Install coolant return tube and its mounting bolt to engine Be sure the slot in tube bracket is bottomed to mounting bolt. This will properly position return tube.
  7. Connect radiator lower hose to water pump.
  8. Connect heater hose and hose clamp to coolant return tube.

Jan 11, 2009 | Dodge Durango Cars & Trucks

Not finding what you are looking for?
1998 Dodge Durango Logo

261 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...