Question about 1992 Jeep Wrangler

1 Answer

Clutch pedal is going to the floor. about 2 mos ago replaced the master cylinder bled the system worked good now its doing the same thing. if i bleed the system it works good again for a day or so. dont know if its the throwout bearing now. hate to pull a tranny if its not. any ideas

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Jeep Master
  • 1,075 Answers

I dont think its bearing problem.Did you fit a [new] master cyclinder,if you did then its the [slave ]cyclinder .,its a pressure problem not a bearing problem.adrian,,,,

Posted on Aug 04, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2004 vectra c diesel clutch pedal to floor. Garage changed csc,master cylinder, return spring but pedal still drops to floor. Not loosing any fluid been bled numerous times.Any ideas??


Crack off the slave cylinder bleed nipple. If you get pressure when pumping the pedal, replace the clutch. If not, remove the air lock in the system or fit a new master cylinder.

Jan 25, 2017 | Cars & Trucks

2 Answers

My clutch pedal stay close to the floor in my Acura CL. Doesnt return fully like it used too. Cant figure it out and I've replaced everythin


Bobbie, If your sure the system is bled properly,did you get the clutch fork back in correct position, was it the correct bearing etc., you may have to adjust the clutch pedal and / or if it has a mechanical return spring, change the spring, it could be weak.
Check the attached links,instruction and guides for clutch pedal adjustment., bleeding,etc.Good luck
"I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."

Clutch Kit Installation Acura CL 2 2L 2 3L

Apr 02, 2016 | Cars & Trucks

1 Answer

2003 Scenic 1.9DCI, new clutch, slave flywheel fitted 18 months ago after clutch failure. Last month pedal went flat to the floor and unable to put into gear. Bled system, car ok for a couple of days then...


There are only a few places air can get in the master cylinder and connections the pipe going to concentric slave the connections to slave or slave itself

Feb 05, 2015 | Cars & Trucks

2 Answers

I have a 95 Wrangler YJ 2.5 with a clutch problem


Hi Bruce
I advise you to check the flexible hose first, if its ok, so the problem is the master/slave cylinders.
Good luck

Mar 08, 2014 | 1995 Jeep Wrangler

1 Answer

1998 nissan altima brakes to the floor


Still air in system, sounds like the master cylinder has ran dry during the bleeding process, pumping more air into system. The lines running to the rear brakes are long, so you must bleed the fluid out the bleed screw in the rear 10+ times each side. Bleed, bleed, and bleed some more, keep bleeding untill that pedal feels good.

Dec 08, 2013 | Cars & Trucks

2 Answers

My clutch doesn't always disengage when the peddle is on the floor and when starting out in first bolts ahead as though the clutch was already part way out. I took it to a shop and they said my clutch...


your clutch master cylinder is right beside your brake master cylinder. I would advise you to replace the master cylinder and the slave cylinder together. The slave cylinder is on the side of the transmission. The slave cylinder does have a bleeder screw on it after the parts are bolted in place fill with dot 3 brake fluid and open the bleeder on the slave cylinder until fluid starts dripping out. Then tighten bleeder then open bleeder and have someone push down on clutch pedal while the pedal is pushed down tighten the bleeder the release pedal. Repeat this procedure until you get no air and the pedal feels normal and you should be good to go. Good luck!

Apr 14, 2011 | 1991 Toyota Celica

1 Answer

Clutch pedal goes to floor no preasure filled and bled slave cyl same result


Hi:
If you have bled the system, you are down to either having a bad clutch master cylinder, or a bad clutch slave cylinder. You could eliminate the slave cylinder by removing the line and capping it off, and if you have a firm pressure on the clutch pedal ( don;'t try to push it down, just check for pressure!) then your slave cylinder is bad. If you cap off the line, and bleed the system, and the pedal still has no pressure, then your clutch master cylinder is bad!

Apr 15, 2010 | 2004 Chevrolet Cavalier

3 Answers

Replace brakes. now they go to the floor. bled air


When you fixed the brakes, did you take the lid off the master cylinder. I just wonder if you spilled out your brake fluid. The only reason the pedal should go to the floor is if the brake fluid is gone or the master cylinder is not working. Check the fuse. Check the brake fluid level. The pedal only goes to the floor if there is no back pressure in the lines between the master cylinder the lines to the brake pistion on the calipers. Please give me a good ratin and keep me informed.

Jul 07, 2009 | 1999 Cadillac DeVille

3 Answers

Just replaced master cylinder on 1990 aerostar and bled the brakes, still the pedal goes to floor and i have no brakes


Did you bench bleed the master cyl. before installing it? then when you installed the new master, did you bleed all 4 points? If yes, then check all for points for leaking caliper/s and leaking wheel cylinder/s. If the van has ABS, check the valve body for a bleeder screw and see if air bleeds out of it. If you've checked everything twice and did everything right then your new master cyl. may be defective.

Apr 29, 2009 | 1986 Ford F 250

Not finding what you are looking for?
1992 Jeep Wrangler Logo

113 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...