Question about 1991 Ford Mustang
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
Here's a link to this great service
Posted on Jan 02, 2017
SOURCE: no injection pulse
looking at the schematics, well the PCM controls the pulse width to the injectors , BUT , there is a injector coil fuse , its #2 in your kick panel fuse box , a 20 amp , check it , sure hope that fix ya . that would be sweet .
Posted on Jan 15, 2009
Very important that if you are not savvy of working on your Vette ...you would be better off - taking your car to a dealership for repairs on your trouble codes. However if you feel that you want to, First locate your car's alcl this component is located just below the instrument panel and to the left of the center console. Remove the plastic cover the first two slots to your right are the A & B slots.
The A slot is the diagnostic slot and the B slot is the ground slot. Insert the computer key into these slots if you do not have a computer key, a paper clip or wire jumper clip will do, (with the engine off) this is very important...now only put the ignition key to on ( not start !!!) the check engine light will display a code 12 which is one flash followed by two flashes. This code will be flashed three times ..followed by the trouble code stored in your car's computer.
What ever the code is it will be flashed three times. Have a paper and pencil ready and write down the code.
Code #12: Normal No Codes.
Code #13: Open Oxygen Sensor Circuit.
Code #14: Coolant Sensor Circuit Low.
Code #15: Coolant Sensor Circuit High.
Code #21: Throttle Position Sensor High.
Code #22: Throttle Position Sensor Low.
Code #23: Manifold Air Temperature Circuit High.
Code #24: Vehicle Speed Sensor.
Code #25: Manifold Air Temperature Circuit Low.
Code #32: EGR System Failure.
Code #33: Mass Air Flow Sensor High.
Code #34: Mass Air Flow Sensor Low.
Code #36: Mas Air Flow Sensor Burn-Off Function Fault.
Code #41: Cylinder Select Error.
Code #42: Electronic Spark Timing.
Code #43: Electronic Spark Control.
Code #44: Lean Exhaust indication.
Code #45: Rich Exhaust Indication.
Code #46: Vehicle Anti Theft Fault.
Code #51: Faulty Mem-Cal.
Code #52: Fuel Calpak Missing.
Code #52(1990-91 Corvette Only): Engine Oil Temperature Sensor Low.
Code #53: System Over Voltage.
Code #54: Fuel Pump Circuit Low Voltage.
Code #55: Defective ECM.
Code #62: Engine Oil Temperature Sensor Circuit High.
Please remember that if you have the computer key installed in the alcl and you start the engine (you will ruin the engine's computer) only put the ignition to on (not to start).
If you should get a check engine soon display.. you can use the above procedure and codes to buy the right part or at the very least to keep from getting taken for a ride and be made to pay hight prices for some inexpensive module that you could have installed yourself.
If your engine displays a trouble code ... your engine will go into limp mode ..it will still run but very poorly. You might be able to reset the computer if it will not start (just to get home) by disconnecting both battery cables and re-installing them ...this is not recommended ..but if you are stranded it might help unitl you get your car home or to a repair shop..good luck.
Good luck and hope this helps.
Posted on May 08, 2009
Before you go any further open the trunk and check the fuel pump roll over valve switch, mounted on the left side inside the trunk, push the switch down and try the vehicle.
Posted on Jun 05, 2010
Pull the return fuel line off the back of the fuel pressure regulator and plugit.
attach another hose and clamp it to the back of thefp regulator place the othe end in a container.
pull the coil wire and have someone crank the engine or use a remote starter switch.there should be a steady stream of fuel into the container. If not check your intank pump and main body pumps for electrical connections.
If there is a steady stream from the fuel rail and still no gas at the plugs.
Find another fuel injector for a volvo,unplug the # 1 injector electrical connnection and plug in the extra one placing it in a container and crank the engine over. There s/b an even spray of fuel from injector.
If not check for 12 volts at the injector connectrion. If no volts,check backwards to the ballast resistor which controls the injectors and then to the radio suppression relay etc.
Posted on Oct 25, 2011
Tips for a great answer:
Feb 02, 2017 | Cars & Trucks
Apr 04, 2016 | 2008 Buick Lucerne CXL
Dec 09, 2015 | 1988 Ford Tempo
Oct 23, 2015 | Dodge Cars & Trucks
Aug 15, 2015 | Pontiac Cars & Trucks
Jan 07, 2013 | 1991 Honda Accord
Jul 31, 2011 | 1992 Mitsubishi 3000GT
Feb 05, 2011 | 2001 Saturn L-Series
Aug 13, 2009 | 1996 Oldsmobile Cutlass Supreme Coupe
Jul 11, 2009 | 2002 Hyundai Accent
315 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: