Question about 2003 Hyundai Tiburon

Open Question

How to remove the input speed sensor on a 2003 tiburon

Posted by on

Ad

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 74 Answers

SOURCE: 2003 tiburon transmission

if you have a 4 cylinder you wiggle the clutch shaft up and down remove the lever and this will get the fingers off the releasbearing / 2 starter bolts 2 large bolts up top 3 under exhaust and 4 0n the other side lower one is above right inner cv axle, remove left axle from car right axle can moved over un do ball joint 3 mounts remover upper side and reaar , strap engine to a cradle or 4,4 post chained to support engine you can slide tranmission over14 inches with room to stick your hands in and remove pressure plate ,fly wheel can be removed but takes good hands tricky,now thats a hyundai flat rate tech procedure for 4 cyl, IF YOUR NOT SURE ABOUT or if the engine is V6 cylinder THE SUB FRAME COMES OUT you can remove rack hose on sub frame and 4 bolts and wire or strap the steering rack to body at that can stay in car or you will have to take rack out with sub frame

Posted on Sep 25, 2008

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

No reverse in my 2006 Hyundai Tiburon hatchback 5 speed what could be problem


"Car won't go in reverse" - New Tiburon Forum : Hyundai Tiburon ...

www.newtiburon.com/forums/.../189049-car-won-t-go-reverse.html

Aug 8, 2010 - 23 posts - ‎16 authors
Okay guys I just sold my 03 tiburon GT 6 speed to a 16 year old. I just got a ... Join Date: Sep 2006. Location: ... "It stalls and just drift forward, no reverse lights" Now did he break somethng or is he putting it in 6th..... Any Ideas. ... To view links or images in signatures your post count must be 5 or greater. Location of reverse light switch? - New Tiburon Forum ...
8 posts
Jul 23, 2014
So who's reverse lights don't work? - New Tiburon ...
25 posts
Apr 11, 2009
More results from www.newtiburon.com
Missing: hatchback

2003 Hyundai Tiburon Manual Transmission Complaints

www.aboutautomobile.com/.../Hyundai/Tiburon/Manual+Transmission
My 2003 hyundai tiburon clutch and flywheel broke on 3 separate occasions since ...into reverse, I had a hard time finding it, it would not let me put it into reverse and I ....2006; Description of the Complaint: I have 2003 v6 tiburon, clutch failed at ... bought 2004 5 speed tiburon (she bought it before my problems started) and ...

Transmission Won't Shift/CEL Due to Failed Speed Sensors ...

repairpal.com > Problems > Hyundai > Sonata

Jan 03, 2016 | Hyundai Cars & Trucks

1 Answer

I have a 2003 Tiburon gt 6 speed. My maf sensor


The computer can not know how much air is
coming in, so you haven't had proper fuel control
for a week or so with no MAF

Oct 01, 2014 | 2003 Hyundai Tiburon

2 Answers

What is the function of wheel speed sensor


Speed sensor sends a signal to the on-board computer reporting the vehicle speed

Dec 12, 2012 | 2003 Hyundai Tiburon

1 Answer

My 2009 Hyundai Sonata quit accelerating while driving in town. The ESC and check engine light came on. I was able to turn the car off and back on and the ESC light went off and acceleration worked...


This may not be your problem but it does bring the vehicle in fail safe you may have a warranty
Group TRANSAXLE
Number 09-AT-016
Date AUGUST, 2009
Model
1999-SONATA
2001-ELANTRA, SANTA FE & XG
2003-TIBURON
2005-TUCSON
2006-AZERA
2007-ENTOURAGE

Subject
AUTOMATIC TRANSAXLE DIAGNOSTIC TROUBLE CODES P0715, P0716, P0717, P0720, P0721 & P0722

An improperly functioning input speed sensor or output speed sensor may result in the following conditions:
^ "Check Engine" light on
^ Harsh P-R or P-D engagement shock
^ Transaxle in 3rd gear fail-safe
^ Diagnostic trouble codes 1. Using a GDS, check for DTCs in both the "Engine" and "Automatic Transaxle" menus. Record the DTC and description.
2. From the GDS, select:
^ Vehicle
^ "Auto Transaxle" menu
^ "Current Data"
^ "Input speed sensor" and "output speed sensor". Drive the vehicle and monitor the input and output speed sensors. If the sensors show:
^ Continuous output, the wiring currently has no open/shorts. Go to Step 6.
^ No output, go to Step 3
3. Check the wiring harness visually for an open circuit or short circuit to ground. Check for a pinched harness at the PCM/TCM attachment bolts.
4. Disconnect the connectors at the input and output speed sensor and PCM/TCM. Check for bent pins or pins not fully inserted into the connector.
5. If a harness open/short is found, repair or replace the ECM control harness between the PCM/TCM and transaxle and go to Step 8. If not, go to Step 6.

Aug 22, 2011 | Hyundai Sonata Cars & Trucks

1 Answer

My boyfriend has a hyundai tiburon 1998 and the it shifts to 3/4 gear. A mechanic told him it needed an input/output sensor but we can't find it anywhere. So,we called the dealer and they say it doesnt'...


It is easiest if you take the air filter and its casing off. use a 8mm wrench to disconnect the top of the case. there should be three 10mm bolts holding the bottom of the case to the frame. Once the air filter case is off the speed sensor connection is almost directly under it, slightly more towards the engine, on top of the automatic transmission. A 1998 Tiburon has a pulse generating speed sensor, which means there is only one connection to deal with, but it has two sensors which bolt onto the transmission. To remove the old sensor, press the release pin on the connection, to do this I use a small Allen wrench. It is easiest to follow the lines of the old sensor to find where the two sensors are to be placed. Once the two sensors are found, they can be removed using a 10mm wrench. it may be easiest to replace the far sensor with the driver side wheel removed, or at least the car should be elevated.Good luck and keep me posted.

Jan 18, 2010 | 1998 Hyundai Tiburon

1 Answer

Cant seperate trans from motor 2003 tiburon 2.0 manual all bolts removed


At the top of the transmission where the hydraulic clutch cylinder rod is attached, you have to remove the lever from the shaft (14mm nut), because the clutch is the 'PULL' type pressure plate bearing system. After you remove the trans, you will need to remove the bearing from the pressure plate and put it back on the input shaft collar in the trans before reinstalling the trans.

Oct 14, 2009 | 2003 Hyundai Tiburon

1 Answer

My car is high reved at 2000 rpm wont go down


Have you tried just disconnecting the battery for a half an hour or so? Your ECU probably just needs to forget what it has learned and relearn it.

Sep 30, 2009 | 2003 Hyundai Tiburon

1 Answer

Output Speed Sensor


dear friend:plse make sure that you replaced the output sensor and not the input speed sensor.the output speed sensor is the one closer to the fire wall,

Sep 16, 2009 | 2004 Hyundai Tiburon

1 Answer

4 cylinder motor


http://www.analogstereo.com/pdf/om/hyundai_tiburon_owners_manual_2003.pdf
note_icon.gif Mark all wiring and hoses to avoid misconnection. Inspection the timing belt before removing the cylinder head. Turn the crankshaft pulley so that the No. 1 piston is at top dead center
1. Disconnect the neagative terminal from the battery 2. Remove the engine cover. . Drain the engine coolant. Remove the radiator cap to speed draining. 4. Remove the intake air hose and air cleaner assembly. (1) Disconnect the AFS connector. (2) Disconnect the breather hose from air cleaner hose. (3) Remove the intake air hose and air cleaner. 5. Remove the upper radiator hose (A) and lower radiator hose (B). 6. Remove the heater hoses 7. Remove the engine wire harness connectors and wire harness clamps from the cylinder head and the intake manifold. (1) OCV(Oil Control Valve) connector (A). (2) Oil temperature sensor connector (B). (3) ECT (Engine Coolant Temperature) sensor (C) connector. (4) Ignition coil connector (D). (5) TPS (Throttle Position Sensor) connector (A). (6) ISA (Idle Speed Actuator) connector (B). (7) CMP (Camshaft Position Sensor) connector (A). (8) Four fuel injector connectors (B). (9) Knock sensor connector (C).

May 27, 2008 | 2003 Hyundai Tiburon

Not finding what you are looking for?
2003 Hyundai Tiburon Logo

Related Topics:

66 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

76132 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...