Question about 1998 Acura TL

Open Question

Where is the code reader port on a 1998 Acura 3.2TL. I have an OBD2 reader but cant find the port on th car...

Posted by on


5 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

  • 1077 Answers

SOURCE: where is the obd2 plug in on a acura 3.2tl???

Center console,behind a cover,front of trans shifter handle

Posted on Mar 22, 2009

  • 1986 Answers

SOURCE: where is the obd2 plug in on a 2000 acura TL

remove the plastic panel underneath the ashtray and you'll see it

Posted on Aug 13, 2009

  • 11 Answers

SOURCE: obd2

you are need to look in the port itself sometimes the pins get bent or what not.

Posted on Apr 05, 2009

  • 1049 Answers

SOURCE: where is my obd2 connecter?

HI, i find a picture for you, hoping help.


Posted on Jun 16, 2011

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Does the 1994 Olds 88 royale have an OBD port? If so, where is it located?

Almost certain there is a port somewhere but I don't know where but as it is pre-obd2 it could be almost anywhere.

Generic obd2 code readers and scanners mostly won't read obd1 though sometimes will read a small amount. Unless you have a dedicated code reader or scanner there will be no point finding the port - unless the the port can be used to activate a blink code. In that case you will need accurate instructions how to proceed, instructions that will also probably tell you where the port is to be found.
Pre obd2 ports don;t even have to be the now-standard 16 pin type and could be any size or shape.

Mar 04, 2018 | Cars & Trucks

2 Answers

Plug in my scan reader to 1998 frontier pickup and it wont power up to read codes

Check pin 16 for voltage at obd2 connector. Should be hot all the time, probably a fused circuit. Sometimes it's the cigar fuse that powers that circuit, I'll have to check.

Apr 11, 2016 | 1998 Nissan Frontier

3 Answers

Code reader can't connect with vehicle computer.

Check for a blown fuse, some times the OB2 port shares the fuse like cigar lighter ,etc
press the helpful button

Feb 05, 2016 | 2000 Isuzu Rodeo

1 Answer

How do I pull obd2 codes from my 1998 Chevy dually 3500. 7.4l v8 4l80e, 16 pin obd2 port without a code reader? My transmission started to shift really hard thru the gears now has a check engine light

have it read by a garage ,but hard gear changes is normally down to low transmision fluid ? as for engine light well it could be anything and you need to read the codes

Jan 23, 2016 | Cars & Trucks

1 Answer

How do I reset acura a146 code?

You need an obd2 reader to reset the codes. But if you reset the codes without making the repairs the codes return after you drive 10 miles or so.

Aug 02, 2014 | 2007 Acura MDX

1 Answer

How to check engine codes without odi scanner

in the USA you cant. That ended in 1995! or even before.
all 1996 cars in the USA are OBD2, it's the LAW.
the tools is $9 on fleabay
the code reader(cant scan ) can read all bad DTC errors
$20 bucks

all auto stores in usa will scan it for free, call em'
most stores rent it for free. or $5
all auto shop will scan it for free, many do.
what's the big deal, in remote Alaska village? what?

if not in the USA, then why not say so, at that is different.
each country has its own laws. on this.

Feb 16, 2014 | 1998 Toyota 4Runner

2 Answers

Where do i plug the code reader in?

In the center console, lift up the ash tray dish. There should be a rubber flap that covers the OBD connector.

Apr 14, 2011 | 1998 Acura TL

1 Answer

My check engine light and TCS light came on in my 1999 Acura 3.2TL. I had the code cleared out and it appears to be running fine. The code came up 1705 Transmission sensor out of range. No one including...

acura 1999 3,2tl .check engine light on ,my computer show code P0141 , 02 HEATER CIRCUIT, [BANK 1, SENSOR 2] please to help find problem .thank you

Mar 16, 2010 | 1999 Acura TL

1 Answer

2001 new beetle won't start has new battery

I have a 2003 new beetle TDI. I have got error codes on my ECM that have stopped my engine from starting. I got an OBD2 reader from the auto parts store. I plugged it into the OBD2 port below the steering wheel and got the error codes. After writing them down, I cleared the codes. the car started fine. It has pulled this a couple times over three years. I carry an OBD2 reader with me so I can clear the codes and get going again. Good Luck

Sep 25, 2009 | 1998 Volkswagen Beetle

1 Answer

Where is the obd2 plug in on a acura 3.2tl???

Center console,behind a cover,front of trans shifter handle

Mar 22, 2009 | 1996 Acura TL Series

Not finding what you are looking for?
1998 Acura TL Logo

Related Topics:

695 people viewed this question

Ask a Question

Usually answered in minutes!

Top Acura Experts


Level 3 Expert

81294 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you an Acura Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides