Question about 1998 Ford Expedition

1 Answer

Need info on 1998 Ford Expedition Air Suspension

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Ford Master
  • 17,970 Answers

Excalty, what is info that you need?

Posted on Aug 03, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Air suspension in rear not inflating all fuses are fine


There is a relay for the air ride suspension. And also the compressor could be bad.

Apr 13, 2013 | 1998 Ford Expedition

1 Answer

I need to know where the air suspension relay is located in a 1998 ford expedition


Sorry, I can answer you because have other question open; check the next image (position 4)...

222113c.jpg

Other details in the Ford-Expedition page 135 and next.

Hope helps (remember rated this).

Jun 23, 2010 | Ford Expedition Cars & Trucks

1 Answer

How to change rear air suspension on 1999 ford


Change the air suspension to a non air conversion system from Strutmasters. Their kit will save you lots of money and time. Check them out!

May 14, 2010 | 1999 Ford Expedition

1 Answer

Check suspension?


Check suspension
Illuminates momentarily when the
ignition is turned to the ON
position and the engine is OFF.
The light also illuminates when the
air suspension system requires
servicing.

Nov 18, 2009 | 1998 Ford Expedition

2 Answers

Where do I find a fitting or connector to repair the air line to my Ford Expedition Air Suspension?


you can get push on spring loaded couplings and other air hose parts at nappa auto store.

Aug 14, 2009 | 1998 Ford Expedition

2 Answers

Rear suspension on 1998 Ford EXP wont raise


More than likely you have an inner leak in one of the strut assem. in rear.

Jun 16, 2009 | 1998 Ford Expedition

1 Answer

I have a 1998 ford expedition eddie bauer with front air bag suspension and after driving for about 45 minutes the air suspension light comes on. what's the problem and how do I fix it


here's some info. Do you have a warning light on or does it say "Check Susp"?

Control Module
NOTE: The 4-wheel air suspension (4WAS) control module is also used for the rear air suspension (RAS) system. The internal processor recognizes external circuitry to determine if it is installed in a 4WAS or a RAS system.
NOTE: The air suspension control module is calibrated with information from the air suspension height sensors. A new or swapped air suspension control module requires the ride height adjustment calibration process to be performed.
A microcontroller-based electronic air suspension control module controls the air compressor motor (through a solid state relay), and all system solenoids. The air suspension control module also provides power to front and rear height sensors. The air suspension control module controls vehicle height adjustments by monitoring the two height sensors, vehicle speed, a steering sensor, acceleration input, the door ajar signal, transfer case signals, and the brake pedal position (BPP) switch. The air suspension control module also conducts all fail-safe and diagnostic strategies and contains self-test and communication software for testing of the vehicle and related components.
The air suspension control module is mounted in the passenger compartment inside the instrument panel, above the radio and temperature controls. The air suspension control module is interchangeable between the RAS and 4WAS system.
The air suspension control module monitors and controls the system through a 32-pin two-way connector. The air suspension control module is keyed so that it cannot be plugged into an incorrect harness. There are two sides of the harness connection to the air suspension control module. Each is uniquely colored and keyed to prevent reversing the connections.
Solenoid, Air Spring
swj~us~en~file=ani_caut.gif~gen~ref.gif WARNING: Never rotate an air spring solenoid valve to the release slot in the end cap fitting until all pressurized air has escaped from the spring to prevent damage or injury.
The air spring solenoid:
  • Allows air to enter and exit the air spring during leveling operations.
  • Is electrically operated and controlled by the air suspension control module.
  • Is only replaced as a unit.
Air Suspension Diagnostic Connector
The air suspension diagnostic connector is used to aid the technician in diagnosing the air suspension system. It is also used to vent the system of compressed air when air suspension system components need to be repaired or replaced. The air suspension diagnostic connector is located under the steering column.
Steering Sensor
The steering sensor is mounted inside the passenger compartment on the steering column. It provides steering rate and position to the air suspension control module through two signals.
Pressure Relief Valve
The pressure relief valve (PRV) protects the rear air suspension components by venting the system to a specific pressure in the case of a system malfunction. The system will decrease the pressure to an acceptable level to maintain vehicle height. In the normal operation mode with normal system pressure the PRV is constantly closed and does not have any effect on the system performance or function. The PRV is replaceable without any air lines.
The PRV is located in the rear of the vehicle on the middle of crossmember #5 as a part of the rear air line assembly.

Mar 09, 2009 | 1998 Ford Expedition

Not finding what you are looking for?
1998 Ford Expedition Logo

Related Topics:

18 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

Marvin
Marvin

Level 3 Expert

81285 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

gerry bissi

Level 3 Expert

4376 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...