Question about Dodge Caravan

Open Question

REMOVE AND INSTALL A 1999 DODGE CARAVAN FRONT BUMPER COVER

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
tommyboinow
  • 324 Answers

SOURCE: trying to remove radiator,condenser,fan assy,

you should not have to remove the bumper to replace these, you will have to remove the core support, wich you will see 2 bolts on each side, just oin front of the radiator....

Posted on Nov 26, 2008

Ad
dgjtex
  • 405 Answers

SOURCE: 1999 Accord front bumper cover

I do this for a living and I think I can help you.
The bumpers are available for around 35.00 wholesale, the paint is waht is expensive, Installation is a breeze. Bolts on each side and clips to wheel skirts, Headlights may need to be removed I can't remember, also under the car is a shield that attaches to the cover. It will come right off after that. I think a couple of clips under the hood holding it to the core support, I do so many of these it is hard to remember exactly how each one is attached, but just installed one on and acura rsx,. Hope this helps you!

Posted on Dec 26, 2008

  • 1596 Answers

SOURCE: replacing front bumper on 1999 buick regal

7/16th or 10mm Sheetmetal nuts All over Behind the Bumper Thak Bumper off first

Posted on Jan 16, 2009

  • 6 Answers

SOURCE: 2005 Honda Accord Front Bumper cover replacement

easy there is a screw on both sides were bumper and fender meet just pop back fender liner its a phillips head. Then pop hood remove clips on black trim infont of radiator. Underside where bumper goes under car remove those clips and 10mm bolts after all is removed bumper just pulls off ...... may have to give it a hard **** a few times but it will come off. Should only take 15-20min to remove if its your first time

Posted on Jul 03, 2009

  • 1986 Answers

SOURCE: I'm not sure how to remove the exterior door trim

On the inside trim, you can remove screws (these screws may be covered by filler pieces or may be visible, or they may require you pry a plastic piece off that covers the screws) that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. Then you'll need to manipulate the panel and disconnect the door handle linkage from the door handle and disconnect any other wiring that may be attached to the door. Then you need to pull back the weather seal and then you can disconnect the screws and clips that secure the outside trim to the door.

Posted on Nov 03, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Dose anyone know how to remove a front bumper cover on a 2000 dodge caravan?


https://www.youtube.com/watch?v=BCaZGTz1WLw

Not the specific video for your vehicle but this can assist you in the general methods and procedures in replacing a front bumper cover.

Nov 13, 2016 | 2000 Dodge Caravan

1 Answer

I can't locate my horn on my 1996 dodge caravan


Behind the front bumper on the passenger side. Remove the bottom cover to gain access.

Nov 21, 2015 | Dodge Cars & Trucks

1 Answer

Location of 2004dodge caravan cooling fan relay show photo


Remove the front number. Ou will see it riveted to the bumper frame of the drivers side. If you remove the screws that holt the top of the bumper to the upper radiator cover and gently pull back on the grill part of the bumper you will see it.

Apr 07, 2013 | 2004 Dodge Caravan

1 Answer

2011 Dodge Caravan. Ran into a metal wheelchair ramp rain. Drove back - dislodged - the black trim insert near the bottom of the plastic bumper cover. That black plastic thing has to be just put back on...


Hello Bruce...here are the steps to follow per All Data.

Release hood latch and open hood.
Remove the headlamp assemblies.
Hoist vehicle and support with safety stands.
Remove the five push pin fasteners attaching bottom of fascia/air dam to radiator closure panel.
Remove front wheels.
Remove front wheelhouse splash shields fasteners as necessary to gain access to bolts attaching front fascia to fender.
Remove the two bolts and two nuts attaching fascia to the front fenders (Fig. 1) and (Fig. 2).
Disconnect fog lamp wire connectors, if necessary.
Lower vehicle.
Remove two bolts attaching the upper grille support to the headlamp mounting panel at each side of the grille.
Remove bumper fascia from vehicle.
INSTALLATION

Position front bumper fascia on vehicle (Fig. 1) and (Fig. 2).
Install the two bolts attaching fascia to headlamp mounting panel at each side of grille.
Hoist vehicle and support with safety stands.
Install the two bolts and two nuts attaching fascia to the front fenders. The fascia should be flush to fender.
Install front wheelhouse splash shields fasteners.
Install front wheels.
Connect fog lamp wire connectors, if necessary.
Install the five push pin fasteners attaching bottom of fascia to radiator closure panel.
Lower the vehicle.
Install the headlamp assemblies.

The "push pin fasteners" are the pain you are having i believe. They push in, but to get them out you need squeeze them on the back & pull at the same time. If you happen to break a few, you can buy them in various sizes at the auto parts store. I hope this information is helpful, an owners manual will not have any info like this in it.



12_2_2011_5_37_49_pm.jpg

Dec 02, 2011 | Cars & Trucks

1 Answer

How do you remove the front bumper to get to the radiator


If you need to remove the entire front bumper. Remove the 3 Phillips head screws in each inner fender (both sides edge of bumper by wheel). Remove the two 8mm bolts that you now have access to and go straight up (behind the inner fender). Remove the three 10mm bolts along the top of the radiator. Crawl underneath and pull the centers out of the plastic push clips (seven I think). Slide the bumper off.

Hope that helps, thanks for using FixYa.

Apr 10, 2010 | 1999 Dodge Caravan

1 Answer

Where is the Front impact sensor for the airbags located on a 2003 Dodge Caravan


if you were to pull the front bumper off youll see a metal cover running the width of the vehicle. there are 4 of them through there

Nov 20, 2009 | 2003 Dodge Caravan

1 Answer

1999 Dodge Neon rear license Plate bulb


LICENSE PLATE LAMP BULB
REMOVAL
  1. Remove screws attaching license plate lamp to rear bumper
  2. Remove lamp from bumper.
  3. Remove bulb socket from lamp.
  4. Pull bulb from socket.

INSTALLATION
  1. Install bulb into socket.
  2. Install bulb socket into lamp.
  3. Place lamp in position.
  4. Install screws attaching license plate lamp to rear bumper.

Oct 08, 2009 | 1999 Dodge Neon

3 Answers

Where is the horn


behind the steel re-inforcing bar for the front bumper. Look at the front of the Vehicle and it's on the right

Aug 02, 2009 | 1999 Dodge Caravan

1 Answer

Replacing front bumper on 1999 buick regal


7/16th or 10mm Sheetmetal nuts All over Behind the Bumper Thak Bumper off first

Jan 01, 2009 | 1999 Buick Regal

1 Answer

1997 dodge caravan waterpump replacement


OK, disconnect neg battery cable, drain cooling system, remove splash shield under right front fender for easy access to water pump bolts, loosen clamps and disconnect hoses from pump, remove drive belt, remove water pump pulley bolts, remove pulley (tip: loosen bolts on pulley before removing belt), remove water pump bolts (5) , separate from the front cover, clean the bolt threads and the threaded holes in the front cover to remove any corrosion and sealant, remove and discard o ring and clean mating surfaces, careful not to gouge or scratch mating surfaces, install new o ring into the groove, install the pump to the front cover and tighten to 105 INCH pounds, pulley bolts are 21 FOOT pounds.Good Luck! countrycurt0

Oct 05, 2008 | 1997 Dodge Caravan

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

438 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

76051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8265 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...