Question about 1984 Dodge Ramcharger

1 Answer

1984 dodge charger. how to i get to the starter

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Dodge Master
  • 17,970 Answers


Starter - REMOVAL & INSTALLATION
The starter is an overrunning clutch drive type with a solenoid mounted on the starter motor. Six different type starters are used on these models. Two each are built by Nippondenso, Bosch and Mitsubishi for manual and automatic transaxle applications. Removal and installation procedures are the same for all units. Some early production models may experience starter motor damage due to improper fit of the upper and lower steering column shrouds. Irregularities in the mating surface of the key cylinder area may cause the ignition key to bind, causing the starter to be continuously engaged. The condition can be corrected by loosening the shroud cover screws about 1 1 / 2 turns.
If loosening the screws does not solve the problem, the covers will have to be replaced with new parts, which are available only in black and must be painted to match interior trim.



  1. Disconnect the negative battery cable.
  2. If equipped, remove the heat shield.
  3. On the 2.2L loosen the air pump tube at the exhaust manifold, then swivel the bracket away from the starter.
  4. Remove the wires from the starter and solenoid.
  5. Support the starter, remove the bolts and lift the unit out from the flywheel housing.
  6. Installation is the reverse of removal.
1984 dodge charger. how to i get to the starter - 22281f5.jpg

Fig. 1 Starter mounting on the 1.6L engine (click for zoom)

50cdf32.jpg

Fig. 2 Mounting for the 1.7L engine with A-412 manual transaxle

4252200.jpg

Fig. 3 Mounting on the 1.7L engine with the A-404 automatic transaxle

08554c3.jpg

Fig. 4 Mounting for the 1.7L A-460 manual transaxle and the 2.2L manual or automatic transaxle




Hope this help; remember comment and rated this.

Posted on Aug 03, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Change starter 1984 dodge rampage


How do I remove the starter on a 1984 dodge rampage? It is really hard to get to.

Jul 05, 2012 | Dodge Rampage Cars & Trucks

1 Answer

No spark after truck has been driven a few miles 1984 Dodge d150 318ci Changed ignition modules but no change.


check wire connections at coil, starter,and distributor, also check pickup in distributor.
check coil wire at coil tower,and distributor cap.
i hope you find it!

Oct 18, 2011 | 1984 Dodge D150

1 Answer

All connections are good as far as i can see...when i try to start it the starter kinda clicks like its not getting enough juice or battery is dead....so i put jumper cables on it also and same...


Chances are the brushes inside the starter are worn. The way a starter is wired internally, the solenoid pull in winding is taken out of service if the brushes are worn to prevent internal damage to the starter. Have the starter checked by a qualified person.

Jan 21, 2011 | 1984 Dodge Pickup 4WD

1 Answer

I have an old car but it very old it a 1984 and have a problem to take out the starte so can you please explain me how to do it


Disconnect the battery. To find the starter trace the wire from the battery and it will go to the starter. Disconnect the wires from the starter (make a note of which wire goes where) then remove the two bolts and the starter will come off. Make sure you purchase a new solinoid (bendix) with the new starter.

Mar 05, 2010 | 1984 Dodge Caravan

2 Answers

1984 Dodge Ram Prospector, Not turning over


DID YOU GET THE PROBLEM SOLVED, IF NOT MY PROSPECTOR DOES THIS ON SEVERAL OCCASIONS AND FOUND TO BE LOOSE GROUND CONNECTION

Oct 06, 2009 | 1984 Dodge Pickup 4WD

1 Answer

I have a 1971 dodge charger and my back lights are looking shabby anyone got any ideas


Check in at (allpar.com) and maybe sign up to post question. They should have lots of ideas & sources.

Jun 01, 2009 | 1984 Dodge Charger

Not finding what you are looking for?
Cars & Trucks Logo

339 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...