Question about Chevrolet Silverado 1500

1 Answer

The fan on my 2000 chevy silverado only works on 3,4, and 5 what is causing this and how do I get to it

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,608 Answers

The problem is the blower motor resistor module.It is located on the passengers side by the blower motor under the dash panel.Just locate the blower motor and the connector goes from the blower motor to the resistor.I believe there are 2 screws that hold it on.Make sure you check the connector and look it over for melting or getting hot.Hope this helps.Good luck.

Posted on Aug 03, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Fuse box 2000 Chevy silverado


there are like 3 for a 2000 chevy silverado. 1 on left side of dash accessible only when door is open. 2 on right side of dash, not sure those fuses are applicable to you tho, and 3 under hood beneath a plastic cover that you snap off by pulling on.

May 13, 2014 | 2000 Chevrolet Silverado 1500

1 Answer

2000 chevy silverado no heat comeing from heater fan, only cold air


I had the same problem, my thermostat was stuck open.. I got one of the more expensive ones ($14) at my local parts store and put it in, now she gets hot quick! before i would almost be to work before i felt any heat

Jan 21, 2011 | 2000 Chevrolet Silverado

1 Answer

2000 Chevy Silverado normal operating temp is 210 , recently temp rises to 250. Its been this way for a few days, common operating temp is around 240-250 now, but does not overheat. Coolant levels are...


250 TOO HOT FOR ENGINE AND TRANSMISSION. SOUND LIKE COOLING FAN CLUTCH BAD ITS FREEWHEELING NOT LOCKING UP TO DIRECT DRIVE TOO COOL ENGINE OFF BECAUSE THE FAN CLUTCH THERMOSTAT NOT WORKING THE HOT SILICONE OIL CAUSE IT TO EXPAND TO PUT RESISTANCE ON CLUTCH TO PUT DRAG ON FAN CLUTCH CAUSING IT TO LOCK IN GIVE IT DIRECT DRIVE.I WOULD STILL REPLACE THERMOSTAT AND RADIATOR PRESSURE CAP IF TEMPERATURE STILL 250 DEGREES YOUR RADIATOR AND COOLANT SYSTEM NEED FLUSHING.

Aug 17, 2010 | 2000 Chevrolet Silverado

1 Answer

I have a 2000 Chevy Silverado. When the vehicle


the oil pressure sender unit tip is got sut build up remove it, clean or replace it. when oil is thin it gets right in but while its cold and thick it wont trigger the sending unit. causing light to come on.

Jan 10, 2010 | 2000 Chevrolet Silverado

2 Answers

How many lbs. of freon for 2000 chevy silverado 2500 5.3ltr.


if its a new body style (with the round front - i am assuming because it has a 5.3) then it takes 2.0lbs (.91kg). Make sure you check your fan clutch to see if it spins freely or has some drag to it. the fan clutches usually fail causing the compressors to come apart, the failed ones spin freely.

Jun 04, 2009 | 2000 Chevrolet Silverado 2500

1 Answer

Ac belt replacement


You must remove the fan belt first by wrenching the spring loaded tightener and the same must be done for the compressor belt.

Mar 15, 2009 | 2000 Chevrolet Silverado 1500

1 Answer

Chevy silverado 2000 serpentine belt replacement?


Mike, the belt routing should be on a sticker under your hood, these use a spring belt tensioner and it is easiest to us a 3/8 or 1/2 breakover to pull the tensioner back then the belt is easily removed and replaced, please do not rate me at all if it is not a fixya, thats the only reason do this is for my score. Thanks, and merry Christmas.

Dec 20, 2008 | 2000 Chevrolet Silverado 1500

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

127 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...