Question about 2003 Porsche 911 Carrera

1 Answer

Over the last 4 hours of driving my 84 911, it has been gradually loosing low speed torque and throttle response. idle seems normal and no ignition misses so I doubt its electrical. Valves are a bit out but not bad, spark plugs are a little more than half life. O2 sensor is only 800 miles old. It seems to have normal power at mid and high rpm. Has the same feeling my old hot rods had when I had a vaccum leak or a disconnected vacum advance on the distributor. Up until a few days ago throttle response was crisp with minimal throttle input. Car would climb a hill in fifth gear at 2K RPM and not complain a bit. Now it lugs and takes more throttle and more RPM to do the same thing.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Porsche Master
  • 896 Answers

Check fuel and air filters

Posted on Aug 04, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1994 Saturn SL... Began putting while driving. Sluggish response to pedal. Now starts, revs to about 3000, then dies. Changed the ECTS, Cleaned the EGR... Still won't hold idle. HELP PLEASE!!!


Try cleaning the throttle valve and the idle speed control air bypass valve. Only use throttle valve spray cleaner and harsh abrasives, soak them and clean with the throttle valve with a soft cloth. Soak the idle speed control valve for an hour and then blow it out with compressed air.

May 26, 2016 | Saturn Cars & Trucks

1 Answer

What is a solution to fixing the mass air flow system, with code po121


DTC P0121: Throttle Position (TP) Sensor 1 Performance
Circuit/System Description
The engine control module (ECM) uses the following information to calculate an expected airflow rate:
?€¢
The throttle position (TP)


?€¢
The barometric pressure (BARO)


?€¢
The manifold absolute pressure (MAP)


?€¢
The intake air temperature (IAT)


?€¢
The engine RPM


P0121 The predicted air flow and the predicted MAP combined are outside a calibrated range for more than 3 seconds.
Circuit/System Testing

  1. Inspect for the following conditions:
  2. ?€¢
    Vacuum hoses for splits, kinks, and proper connections as shown on Vehicle Emission Control Information label


    ?€¢
    Inspect thoroughly for any type of leak or restriction


    ?€¢
    Air leaks at throttle body mounting area and intake manifold sealing surfaces


    ?€¢
    Throttle body for dirt, debris, and coking--Refer to Throttle Body Cleaning.

  3. Allow the engine to reach operating temperature. Observe the MAP Sensor Voltage parameter with a scan tool. Voltage should be more than 0.8 volt and less than 4 volts.
  4. ?‡'
    If more than 4 volts or less than 0.8 volt, refer to DTC P0106.

  5. Idle the engine. Observe the MAP Sensor kPa parameter with a scan tool. Increase the engine speed slowly and then back to idle. The MAP sensor kPa should change smoothly and gradually as engine speed is increased and returned to idle.
  6. ?‡'
    If the MAP sensor kPa does not change, refer to DTC P0106.

  7. Take a snapshot of the engine data list while performing the actions listed below. The mass air flow (MAF) sensor g/s should change smoothly and gradually as the engine speed is increased and is returned to idle.
  8. ?€¢
    Idle the engine.


    ?€¢
    Increase the engine speed slowly to 3,000 RPM, then back to idle.


    ?€¢
    Exit from the snapshot and review the data.


    ?€¢
    Observe the Mass Air Flow (MAF) Sensor parameter frame by frame with a scan tool. The MAF sensor g/s should change smoothly and gradually as the engine speed is increased and is returned to idle.


    ?‡'
    If the MAF sensor g/s does not change smoothly and gradually as the engine speed is increased and is returned to idle, refer to DTC P0101 or P1101.

  9. Inspect the throttle body for the following conditions:
?€¢
Loose or damaged throttle blade


?€¢
Broken throttle shaft


?€¢
Any throttle body damage


?‡'
If any of these conditions exist, replace the throttle body assembly.

Jun 20, 2015 | 2008 GMC Sierra 1500 2WD

1 Answer

How do I adjust low idle adaptation on 2005 Tacoma prerunner 4.0


1. Relearn the idle speed by disconnecting the EFI fuse and the ECTS fuse from the under hood fuse box. Leave the fuses out for 2-3 minutes minimum. Reinstall the fuses. Using your finger, push the throttle plates closed completely. Hold the throttle plates closed completely and have a helper turn the ignition switch on. Release the throttle plates as soon as the key is turned on. Reinstall the boot to the throttle body and start the vehicle. Allow the vehicle to idle for 5 minutes. Test drive the vehicle and check for normal idle operation.

Sep 30, 2014 | 2005 Toyota Tacoma PreRunner

1 Answer

My 02 cavalier will not shift when I quickly press accelerator it just revs up but if I let off gas and I ease into it like normal it shifts smooth. Just changed transmission fluid and filter along with...


The transmission has servo shift sensor and can be affected by the speed sensor . Should the speed sensor not be the problem and it the other I recommend you find a used transmission with low mileage seek an experience mechanic to install with new fluids in tranny and torque convertor

Aug 24, 2014 | Cars & Trucks

1 Answer

Truck dies when idling


HI
first I would like to tell you, do this procedure only if the 5th digit of your VIN is C or K.

Description

The engine control module (ECM) learns the idle position of the throttle plate to ensure the correct idle. Anytime the throttle body is cleaned or replaced, the ECM must learn the new throttle position. The idle may be unstable or a DTC may set if the throttle position is not learned.

Conditions for Running the Throttle Learn Procedure

• DTCs P0101, P0102, P0103, P0107, P0108, P0111, P0112, P0113, P0506, and P0507 are not set.

• The engine speed is between 450-4,000 RPM.

• The manifold absolute pressure (MAP) is greater than 5 kPa.

• The mass air flow (MAF) is greater than 2 g/s.

• The ignition 1 voltage is greater than 10 volts.

Throttle Learn

Important: Do NOT perform this procedure if DTCs are set. Refer to Diagnostic Trouble Code

(DTC) List - Vehicle.

1. Start and idle the engine in PARK for 3 minutes.

2. With a scan tool, monitor desired and actual RPM.

3. The ECM will start to learn the new idle cells and Desired RPM should start to decrease.

4. Ignition OFF for 60 seconds.

5. Start and idle the engine in PARK for 3 minutes.

6. After the 3 minute run time the engine should be idling normal.

Important: During the drive cycle the check engine light may come on with idle speed DTCs. If idle speed codes are set, clear codes so the ECM can continue to learn.

* If the engine idle speed has not been learned the vehicle will need to be driven at

speeds above 70 km/h (44 mph) with several decelerations and extended idles.

7. After the drive cycle, the engine should be idling normally.

* If the engine idle speed has not been learned, turn OFF the ignition for 60 seconds

and repeat step 6.
8. Once the engine speed has returned to normal, clear DTCs.
Good Luck

Mar 04, 2014 | 1995 GMC Sierra

1 Answer

2006 dodge ram 3500 5.9 cummins 6 speed manual... I have an intermittant throttle response problem that is becoming more and more frequent. Truck starts and idles normally(hot or cold), takes off...


take it to a dealer with a good desel tech may have a bad injector pump but they are very expencive so make sure thats the problem dont go to a side of the road shop with no idea how to test them

Oct 03, 2013 | 2006 Dodge Ram 3500 Truck

1 Answer

My x type 3.0 has fault readingP1647 could you tell me what this means please


OBDII DTC

P1001 Key on engine running unable to complete; key on engine running aborted

P1100 Mass air flow sensor intermittent

P1101 Mass air flow sensor out of self test range

P1104 Mass Airflow (MAF) Sensor Ground Circuit Malfunction

P1107 Left MAP Sensor Circuit

P1108 Right MAP Sensor Circuit

P1112 IATS Circuit High Voltage

P1113 IATS Circuit Low Voltage

P1121 Pedal Position Sensor Circuit A Range/Performance

P1122 Pedal Position Sensor Circuit A Low Voltage

P1123 Pedal Position Sensor Circuit A High Voltage

P1137 No Rear HO2S Response

P1138 No Rear HO3S Response

P1157 No Rear HO2S Response

P1158 No Rear HO3S Response

P1171 All Cylinders Too Lean

P1172 All Cylinders Too Rich

P1176 Adaptive Fuel Metering Trim Too Lean

P1177 Adaptive Fuel Metering Trim Too Rich

P1178 Adaptive Fuel Metering Trim Too Lean

P1179 Adaptive Fuel Metering Trim Too Rich

P1187 Both Front HO2S Heater Circuits (High Resistance)

P1188 Both Front HO2S Heater Circuits (Open Short to Ground High Resistance)

P1190 Both Front HO2S Heater Circuits (High Battery Voltage Short to Voltage)

P1193 Both Front HO2S Heater Circuits (High Resistance MAF Sensor Fault)

P1194 Both Front HO2S Heater Circuits (Open Short to Ground High Resistance)

P1196 Both Front HO2S Heater Circuits (High Battery Voltage Short to Ground)

P1198 Fuel Level Sensor (High Voltage)

P1199 Fuel Level Sensor (Low Voltage)

P1201 No. 1 Fuel Injector

P1202 No. 2 Fuel Injector

P1203 No. 3 Fuel Injector

P1204 No. 4 Fuel Injector

P1205 No. 5 Fuel Injector

P1206 No. 6 Fuel Injector

P1221 Pedal Position Sensor Circuit B Range/Performance

P1222 Pedal Position Sensor Circuit B Low Voltage

P1223 Pedal Position Sensor Circuit B High Voltage

P1224 Electronic Throttle Control Position Error

P1226 Mechanical Guard Circuit Range Performance

P1227 Mechanical Guard Circuit Low Input

P1228 Mechanical Guard Circuit High Input

P1229 Throttle Control Circuit Malfunction

P1230 Fuel Pump Relay Malfunction

P1235 VSV 1 Circuit Range/Performance

P1236 VSV 1 Vacuum Circuit Failure

P1237 VSV 2 Atmosphere Circuit Failure

P1238 VSV 3 Release Circuit Failure

P1240 Throttle Position Sensor Voltage Malfunction//Sensor Reference Voltage Low (Throttle

Fuel Tank Pressure)

P1241 Throttle Position Sensor Voltage Low Input//Reference Voltage Low (Throttle Fuel

Tank Pressure)

P1242 Throttle Position Sensor Voltage High Input

P1243 Throttle Position Sensor Ground Malfunction

P1245 Crank Signal Low Input

P1246 Crank Signal High Input

P1313 Misfire Catalyst Damage Bank No. 1

P1314 Misfire Catalyst Damage Bank No. 2

P1315 Misfire Excess Emissions

P1316 Misfire Rate Above Limit

P1335 Crankshaft Position Sensor Circuit

P1336 Camshaft Position Sensor (CMP) Circuit Performance

P1361 Ignition Coil Primary Circuit (Cylinder No. 1)

P1362 Ignition Coil Primary Circuit (Cylinder No. 2)

P1363 Ignition Coil Primary Circuit (Cylinder No. 3)

P1364 Ignition Coil Primary Circuit (Cylinder No. 4)

P1365 Ignition Coil Primary Circuit (Cylinder No. 5)

P1366 Ignition Coil Primary Circuit (Cylinder No. 6)

P1367 Ignition Monitor (Bank A)//Ignition System Failure Group 1

P1368 Ignition Monitor (Bank B)//Ignition System Failure Group 2

P1371 Early Activation Ignition Coil (Cylinder No. 1)

P1372 Early Activation Ignition Coil (Cylinder No. 2)

P1373 Early Activation Ignition Coil (Cylinder No. 3)

P1374 Early Activation Ignition Coil (Cylinder No. 4)

P1375 Early Activation Ignition Coil (Cylinder No. 5)

P1376 Early Activation Ignition Coil (Cylinder No. 6)

P1392 Variable Valve Timing Solenoid A Low Input

P1393 Variable Valve Timing Solenoid A High Input

P1396 Variable Valve Timing Solenoid B Malfunction

P1397 Variable Valve Timing Solenoid B Low Input

P1398 Variable Valve Timing Solenoid B High Input

P1400 EGR Valve Position Circuit (Valve Sticking Open or Short)

P1401 EGR Valve Position Circuit (Open Short to Ground)

P1408 EGR Temperature Sensor Circuit

P1409 EGR Valve Circuit

P1440 EVAP Purge Valve Open

P1441 EVAP Valve Circuit

P1443 EVAP Valve Circuit

P1447 EVAP Valve Circuit

P1448 EVAP Valve Circuit

P1454 EVAP System

P1474 Charge Air Coolant Pump Relay

P1475 Radiator Fans Slow Malfunction

P1476 Radiator Fans Fast Parallel Circuit Malfunction

P1506 Idle Speed Control Circuit (Low RPM; Bank B)

P1507 Idle Speed Control Circuit (High RPM; Bank B)

P1508 Idle Speed Control Circuit

P1509 Idle Speed Control Circuit

P1512 Throttle Position Sensor Idle Switch Sense Circuit

P1513 Throttle Position Sensor Idle Switch Sense Circuit

P1514 Park/Neutral Position Switch High Load Neutral/Drive

P1516 Gear Change Park/Neutral Malfunction

P1517 Engine Cranking Park/Neutral Malfunction

P1607 MIL Output Circuit

P1608 Automatic Transmission

P1609 Internal ECM Error

P1641 Fuel Pump Relay No. 1

P1646 Fuel Pump Relay No. 2

P1739 Automatic Transmission

P1775 Transmission Control Module MIL Circuit

P1776 Torque Reduction Request Signal

P1777 Torque Reduction Circuit

P1780 Automatic Transmission

P1781 Automatic Transmission

P1782 Automatic Transmission

P1783 Automatic Transmission

P1785 Automatic Transmission

P1790 Automatic Transmission

P1791 Automatic Transmission

P1792 Automatic Transmission
P1794 Automatic Transmission

Mar 22, 2013 | Jaguar Cars & Trucks

2 Answers

Jaguar xj6 4.0 1990. showing fault code fuel 14, fail 14. what does this code mean ?


2 airflow sensor out of operating range 3 coolant temp sensor out of operating range 4 oxy sensor indicates full rich 5 throttle potentiometer/airflow sensor... (low throttle pot signal with high airflow sensor signal) 6 throttle pot/airflow sensor...... (high throttle pot signal with low airflow sensor signal) 7 throttle pot...idle fuel adjustment failure(idle speed??) 8 intake air temp sensor...open or shorted circuit to sensor 11 Throttle pot at idle: Throttle pot idle trim out of normal range 12 Airflow meter: MAF signal out of range 14 Coolant thermistor: Resistance out of range or static during engine warm up 16 Air thermistor: Resistance out of range 17 Throttle pot: Out of range 18 Throttle pot/Airflow: Low throttle pot signal at high airflow 19 Throttle pot/Airflow: High throttle pot signal at low airflow 22 Fuel pump drive: ECU output to fuel pump relay 23 Fuel supply: Engine running too rich 24 Ignition Drive: ECU output to ignition Amp 26 Air leak: Engine running too lean 29 ECU self check 33 Injector Drive: ECU output to injectors 34 Injector: Looks for Injector dribble 37 EGR Drive: ECU output to EGR switching valve 39 EGR check sensor: EGR not working (normally pipe blocked) 44 Lambda (O2) sensor: Poor mixture control rich or weak (or misfire) 46 Idle speed Control valve: ECU output to Coil AB 47 Idle speed Control valve: ECU output to Coil CD 48 Idle Speed Control Valve: Stepper motor grossly out of position 66 Air pump: ECU output to air pump relay 68 Road speed sensor: Seen speed < 5km/h at high engine airflow 69 Drive/Neutral switch: Seen cranking in "D" or high airflow in "N" 89 Purge Valve drive: ECU output to purge valve
this is all I could find

Nov 09, 2009 | 1990 Jaguar XJ6

1 Answer

Car starts fine but doesn't idle when warmed up.


sound like idle speed control problems.its idling too low.

May 17, 2009 | 2001 Mazda Tribute

Not finding what you are looking for?
2003 Porsche 911 Carrera Logo

82 people viewed this question

Ask a Question

Usually answered in minutes!

Top Porsche Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

ROBERT GARCIA
ROBERT GARCIA

Level 3 Expert

896 Answers

yadayada
yadayada

Level 3 Expert

76051 Answers

Are you a Porsche Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...