Question about Ford Explorer

1 Answer

I need an exploded view of the exhaust system front for a 97 ford explorer xlt,iam trying to see if i can replace the pipe connecting to the front of cat. converter

Posted by on

Ad

1 Answer

Go to auto parts store and check there exhaust parts catalog.

You most likely will have to get a pipe from something else and make up what you need. It is 409 stainless and will need to be TIG welded.

Posted on Aug 04, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Rear washer does not work front ok


The '97 Explorer XLT I owned had a widow washer reservoir (cap) that is visible only when you open the rear lift gate up. Just below window height on the..umm.. driver's side (if not - check the passenger side). Locate it and fill it with fluid.. as I recall my '97 held nearly a gallon.

Oct 08, 2015 | 1999 Ford Explorer

1 Answer

Having a promblem taking off crossover exhaust pipe on a 2005 Buick rendezvous I tooken off the two front exhaust Then took bottom two bolt . But still fasten to something is there other bolts...


Thermostat? engine cooling?
2 engines, here, LYA adn LY7.
nobody here posts engine, why do that?
so ill post only for 1.
the LA1
here are the steps.
NO FSM Sux huh? nor an alldata.com account, why not that? 15 bucks?


STAT out.
Remove the air cleaner and duct assembly. Refer to Air Cleaner Assembly Replacement in Engine Controls - 3.4L.

Drain the coolant until the coolant level is below the thermostat. Refer to Cooling System Draining and Filling (Refer To List 1) .

Remove the crossover exhaust pipe. Refer to Exhaust Crossover Pipe Replacement (Refer To List 2) in Engine Exhaust.

Remove the radiator hose from the thermostat housing.

Remove the thermostat housing bolts and clean any sealer from the bolt threads.

Remove the thermostat housing and gasket.
remove STAT
next is crossover page.

Disconnect the battery ground (negative) cable. Refer to Battery Negative Cable Disconnection and Connection (Refer To List 1) in Engine Electrical.

Remove the throttle body air inlet duct.

Drain the coolant from the cooling system. Refer to Cooling System Draining and Filling (Refer To List 2) in Engine Cooling.

Remove the inlet radiator hose from the engine. Refer to Radiator Inlet Hose Replacement (Refer To List 3) in Engine Cooling.

Remove the thermostat bypass pipe. Refer to Thermostat Bypass Pipes Replacement in Engine Cooling.



Remove the exhaust crossover heat shield bolts.

Remove the exhaust crossover heat shield.
  1. Remove the exhaust crossover pipe studs/nuts.
  2. Remove the exhaust crossover pipe.

end , remove.

now the bypass pipe FWD cars SUCK
  1. Disconnect the left engine mount strut from the engine.
  2. Remove the heater hose from the bypass pipe.
  3. Remove the thermostat bypass pipe to throttle body nut.
  4. Use the J 38185 in order to remove the thermostat bypass pipe hose clamps (1,5).
  5. Remove the thermostat bypass pipe to cylinder head nut (3).
  6. Remove the thermostat bypass pipe bolt (4).
  7. Remove the thermostat bypass pipe hose.
  8. Remove the thermostat bypass pipe.
sigh.....
why not log in to alldata.com
read the page then ask ques tons that are not clear.
and next time post the engine type.
above is just 1 engine.

Jun 18, 2014 | Cars & Trucks

1 Answer

I have a 97 ford explorer xlt. im not sure if it


I would pull the transfer case
Strip it & replace what is needed
& go from there, after reinstall

I would never install a used part
until it stripped it.

Jun 09, 2011 | 1997 Ford Explorer AWD

1 Answer

Will a 98 transmission from a Ford Explorer XLT fit in a 97 Ford Explorer XLT?


No, which kind of surprised me!! Depending on the engine and drivetrain, some 1996 transmissions will work.

May 18, 2010 | 1997 Ford Explorer AWD

1 Answer

I have a 1999 ford f150 exhaust pipe and muffler


did the flange come apart or did the pipe break, if the pipe broke then you will have to replace the system fron the flange back, these exhaust systems look good but corrode from the inside out, get a new system i will probably come in three pieces, and new hangers, its pretty straightforward

Nov 26, 2009 | 1999 Ford F150 Regular Cab

1 Answer

Oxygen sensor for 1999 ford explorer


97 ane 97 have 4. I will assume that yours does too.

Go under Explorer.
Trace exhaust maniford from engine to catalytic converter.... in that path, you will find an O2 sensor (looks like a spark plug right in the exhaust pipe).

Same item on other side.

Now, sad part. You MAY find 2 more O2 sensors just after the converter!!

Autozone can usually do a free diagnostic on your vehicle and tell you which 1 or 2 sensors are bad.

Oct 24, 2009 | 1999 Ford Explorer

1 Answer

Muffler


dealer spares department

Sep 06, 2008 | 2002 Volkswagen Jetta TDI

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

98 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

77514 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

fordexpert

Level 3 Expert

5627 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...