Question about 1995 Lincoln Town Car

1 Answer

How do I disarm a factory alarm? - 1995 Lincoln Town Car

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 1,340 Answers

If you know for sure that 1 fuse controls it,pull it,however that's not likely because fuses usually control more,but if you have the owner's manual,take a look.If not,you have to locate the alarm module.It should have wires going to it.Cut the red one if it does but leave enough room on both sides of the cut wire to cover with electrical tape so it doesn't touch anything and cause problems.If the situation is different,please let me know and we'll figure something new out.Good luck!

Posted on Aug 03, 2010

  • digger_jason Jul 12, 2013

    where is the alarm module located at?

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to disconnect the factory alarm


not sure if your having problems with factory alarm but if it is malfunctioning it most likley will again so here it goes...... to reset alarm insert key in drivers door turn key left then turn key right this should disarm and reset the factory alarm. to disable the factory alarm for good in the drivers door wireing harness look for the factory alarm disarm wire it should be dark green/purple with a negative polarity when your sure you have this wire splice a wire of the same size into it and ground the other end to the frame make sure that you have a good solid ground here and thah where you spliced into the wire is a good connection. this should terminate the factory alarm function hope this helps you

Feb 09, 2015 | 2002 Ford Explorer

2 Answers

How do i disconnect the factory alarm on a 2002 mercury mountaneer


Hello. Alarms are a pain and can cause problems. The best thing to do is disconnect the fuse for the alarm in the fuse panel of the car, then the alarm will not work at all. Also becarefull that it does not cause problems to the car itself. Good Luck.

May 26, 2014 | 2002 Mercury Mountaineer

1 Answer

Anti theft system nissan problems frontier


if its a factory alarm you can disarm it by locating the disarm wire and grounding it out. try www.wirewerx.com for a diagram

Nov 01, 2011 | 1998 Nissan Frontier

2 Answers

How can i disarm the factory security alarm.i have tried the key locks. i have no remote with the car. i didnt know it had an alarm when i bought it . 1995 chrysler cirrus


Here is what I do on my 95 Cirrus I also do not have a keyless remote (well I do but is broke) and after frustation after frustation trying to disarm the factory alarm I find out that by unlocking the passenger front door with the ignition key from the outside will disarm it you may have to try few times before it's disarmed you need to make sure that the blinking red light stops blinking and all of the locks on all 4 door are up or unlocked, this is what I been doing for 3 years now and that's how I disarm the alarm on my car, I hope this helps.

May 15, 2010 | 1995 Chrysler Cirrus

1 Answer

Factory alarm disarm


dealer only ,its built into the ECU have you pushed the fuel cut off switch back down to reset it ?? under the bonnet with a red rubber top on it about an inch square

Jan 04, 2010 | 1999 Ford Expedition

1 Answer

How do i enable factory alarm system without keychain remote?


The Simple Act of Locking the Driver side Door WITH KEY Arm the Factory Alarm. And UNLOCKING Same Door with KEY Disarms it The FOB < Rmote for Alarm Just Honks Horn and Flashes Lights, But it Does the SAME ARMIND & DISARMING. I Hope this Helps You out !!

Jun 15, 2009 | 2000 Pontiac Bonneville

1 Answer

1198 Dodge Ram Pickup


it sounds like you may have an aftermarket alarm system. it can be removed completely from the vehicle. if it is a factory system the key fob or unlocking the door wit the key should disarm the system. if they dont you may want to have a dealer or reputable shop check the system

Oct 12, 2008 | 1998 Dodge Ram 1500 4WD

2 Answers

How to disarm a factory alarm without the keyfab


Have the door panel removed. On the back of the lock cylinder(should be but it maybe loose)harness. manipulate the harness to disarm the factory alarm. Car should start. Vonfrankln@aol.com

Jun 15, 2008 | 1995 Chrysler Cirrus

Not finding what you are looking for?
1995 Lincoln Town Car Logo

126 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lincoln Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

fordexpert

Level 3 Expert

5546 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Are you a Lincoln Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...