Question about Mercury Tracer

1 Answer

Hello I have a 97 mercury tracer ls. One day I went to blow the horn at a driver that had cut me off then the horn blew for a while on its own then stopped. Now it doesn't work. I want to know what I have to do to have it work again. Like what fuse?

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Habit-Forming:

    Visited the website for 3 consecutive days.

    Governor:

    An expert whose answer got voted for 20 times.

  • Expert
  • 162 Answers

Yes you can check the fused . --- but that does not tell me why the fused blow on it own , it could be arelay or the problem is in the steering wheel----- if you find the horn easy , take it out and test it to see if it working. reply

Posted on Aug 03, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the vin located on 97 mercury tracer?


at the base of the windshield on the drivers side. On the build sticker attached to the opening of the drivers front door.

I’m happy to assist further over the phone at https://www.6ya.com/expert/jeremy_d728a59f986299fa

Oct 08, 2016 | 1997 Mercury Tracer

1 Answer

1993 mercury tracer horn wont stop- how do i disconnect it


There are 2, flat metal connectors leading into the horn. Disconnect one or both. This will stop the horn, FOREVER !!!!!!!

Jan 08, 2013 | 1993 Mercury Tracer

1 Answer

1997 mercury tracer o2 sensor removal


Replacement of oxygen sensors on a 1997 Mercury Tracer LS. Sell the Tracer and buy a Ford Focus, or 2010 Chevy Cobalt, or a new Chevy Cruze, or a Ford Fiesta. This solution is best if your Tracer has over 130,000 miles on it.

Feb 16, 2012 | 1997 Mercury Tracer

1 Answer

My sisters 1997 mercury tracer will not shut off, what would cause that? she said that she went to honk the horn and it would not stop and then it shutoff and no longer worked. We replaced the relay and...


This was not a horn problem neither was it the relay but the contacts within the steering wheel that got stuck, u need to have this opened and poped back into position such that when not depressed there wont be any contact.

Jun 12, 2011 | 1998 Mercury Tracer

1 Answer

My mercury tracer 1992 started clicking while driving down the high slowed down then then stopped a little smoke came from there the hood now the car will turn over but wont crank before this happen the...


sounds like your coil went out, i would carefully inspect it looking for burns on it. if it is melted in spots then it will need to be replaced

Apr 27, 2011 | 1992 Mercury Tracer

1 Answer

What will make my 97 tracer while driving rpms drop and car seems as if its off but still running and when i push the gas it does'nt do anything what will cause this


check with scantool for fault code/ massairflow sensor/trottle sensor/pipe at massairflow sensor cut or letting in air

Mar 11, 2011 | 1997 Mercury Tracer

1 Answer

I have a 1997 mercury tracer and the horn wont stop. i beeped at a friend one day and it stoped for 3 seconds and then started again by itself. so i hit it a few times and it stoped. 2 days later i was...


Could be a few thing's , relay sticking ( contacts inside burnt ) intermittant short on the ground wire ,does the vehicle have a content theft system alarm ? could be a input problem to the GEM - generic electronic control module . Looking at a wiring diagram to see what all is involved in the control of the horn an using a DVOM - digital volt ohm meter to test the electrical circuits . Do you know how to do that ? Free wiring diagrams here http://www.bbbind.com/free-tsb Enter vehicle info. year , make , model an engine size . Under system click on interior & driver amenity ,then under subsystem click on horn .I see the RAP module not GEM module for alarm system . Your best bet mite be to take your vehicle to a qualified repair shop . If you do not know how to test the electrical circuits .

Mar 06, 2018 | 1997 Mercury Tracer

1 Answer

Original horn got stuck and burn up, I installed


you may have a problem with the horn button on the steering wheel you might have to pull it apart to find the problem.....hope this helps....cheers

Jul 13, 2010 | 1997 Mercury Tracer

1 Answer

I HAVE A 1997 MERCURY TRACER LS. THE HEATER BLOWER WENT OUT. WHAT IS THE PROBLEM?


Check the blower resister and blower motor connection located under the passenger side of the dash.they have a tendency to get burnt up due to a poor connection .:)

Jan 31, 2010 | 1998 Mercury Tracer

1 Answer

97 dodge 3500 bumper changed no horn i cant locate wiring


They've always been green or green with a black tracer. I think they're both on the passenger side closer to the radiator. If they used to work and now they don't the wires maybe got pinched and then blew a fuse? I can't believe both horns stopped working at the same time.
I hope this helps

Oct 08, 2009 | 1998 Dodge Ram 3500 2WD

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

277 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts

gerry bissi

Level 3 Expert

4376 Answers

Marvin
Marvin

Level 3 Expert

81400 Answers

fordexpert

Level 3 Expert

5687 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...