Question about 1992 Ford Crown Victoria

1 Answer

My speed don't work - 1992 Ford Crown Victoria

Posted by on

  • kiafagoldsmi Aug 03, 2010

    my speed sensor don't work

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Ford Master
  • 6,826 Answers

Speed Sensors REMOVAL & INSTALLATION Front Fig. 1: The speed sensor sits directly over the exciter ring in the front knuckle my speed don't work - 89609p51.jpg
Fig. 2: Detach the speed sensor connector in the engine compartment 89609p55.jpg
Fig. 3: Remove the speed sensor harness from the routing clips 89609p53.jpg
Fig. 4: A special E6 Torx® socket is required to remove the speed sensor retaining boltmy speed don't work - 89609p52.jpg"http://i.fixya.net/uploads/images/89609p52.jpg" alt="89609p52.jpg" class="h_mi" />

  1. Disconnect the negative battery cable.
  2. From inside engine compartment, detach sensor assembly 2-pin connector from the wiring harness.
  3. Remove the steel routing clip attaching the sensor wire to the tube bundle on the left sensor or remove the plastic routing clip attaching the sensor wire to the frame on the right sensor.
  4. Remove the rubber coated spring steel clip holding the sensor wire to the frame.
  5. Remove the sensor wire from the steel routing clip on the frame and from the dust shield.
  6. Remove the sensor attaching bolt from the front spindle and slide the sensor out of the mounting hole. To install:
  7. Install the sensor into the mounting hole in the front spindle and attach with the mounting bolt. Tighten to 40–60 inch lbs. (4.5–6.8 Nm).
  8. Insert the sensor routing grommets into the dust shield and steel bracket on the frame. Route the wire into the engine compartment.
  9. Install the rubber coated steel clip that holds the sensor wire to the frame into the hole in the frame.
  10. Install the steel clip that holds sensor wire to tube bundle on left side or plastic clip that holds sensor to frame on right side.
  11. Reconnect the 2-pin connector to wire harness. Connect the negative battery cable.
Rear Fig. 5: Detach the speed sensor connector in tmy speed don't work - 89609p04.jpgompartment 89609p04.jpg
my speed don't work - 89609p37.jpg. 6: Grasp the harness and . . . 89609p37.jpg
Fig. 9: Remove the sensor retaining bolt and remove the sensor from the hub 89609p34.jpg
  1. Disconnect the negative battery cable.
  2. From inside luggage compartment, detach 2-pin sensor connector from wiring harness and push sensor wire through hole in floor.
  3. From below vehicle, remove sensor wire from routing bracket located on top of rear axle carrier housing and remove steel clip holding sensor wire and brake tube against axle housing.
  4. Remove screw from clip holding sensor wire and brake tube to bracket on axle.
  5. Remove sensor to rear adapter retaining bolt and remove sensor. To install:
  6. Insert sensor adapter and install retaining bolt. Tighten to 40–60 inch lbs. (4.5–6.8 Nm).
  7. Attach the clip holding the sensor and brake tube to the bracket on the axle housing and secure with the retaining screw. Tighten the screw to 40–60 inch lbs. (4.5–6.8 Nm).
  8. Install steel clip around axle tube that holds sensor wire and brake tube against axle tube and push spool-shaped grommet into clip located on top of axle carrier housing.
  9. Push sensor wire connector up through hole in floor and seat large round grommet into hole.
  10. Reconnect sensor 2-pin connector to wiring harness inside luggage compartment.

Posted on Aug 03, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2008 chrysler town country radiator fan don workin high speed


If you have a viscous fan hub attached to the fan then it will not be working at high speed as there will be enough air flowing through the radiator to keep things cool. They only really work at high engine loads and slow speeds (hill climbing ) and at stop lights where the air flow is nill

Jan 22, 2014 | 2009 Chrysler Town &

1 Answer

Speedometer stopped working no speed no kmh


Look you need new speed sensor.

Jun 17, 2013 | Cars & Trucks

1 Answer

I own a 2001 Chevy unpalatable and it work fine and everything but the blinkers don't wanna seem to work properly its like 95% they don't work as for the other 5% the blinkers only wanna work when...


Make sure all outside blinkers are flashing at one speed, if not check the bulbs and all connections, If that doesn't work check flasher

May 09, 2013 | Cars & Trucks

1 Answer

A/C control 1 and 2 not working...No air coming.. but 3 and 4 ok...


You have a faulty blower motor resistor. Usually they're located on the blower motor or behind the A/C controls. The resistor controls speed settings. When they become faulty (common) certain fan speeds don't work or all speeds may fail at once.

Nov 08, 2012 | 1992 Honda Civic

1 Answer

Engine overheating ============ Went fine at higher speed but moment I dropped speed the temperature gauge started going up. There is a whirring sound in the engine (sounded like a tape stuck in the...


Don't know what the "whirring" is, but you NEED to find it. The only reason your temp. goes down at higher speed, is cuz more air is rushing past your car, cooling the engine and radiator. Careful you don't burn up the engine! Find the cause of the overheating, probably related to the sound you hear, or caused by overheating, even maybe causing the overheating. Take your time and work on it or have it serviced. Start by checking your coolant level. Good luck.

Oct 28, 2011 | Cars & Trucks

1 Answer

The ac fan motor in my 2011 Peterbilt only works on high......anyone else have this problem ?


I don't even have a 2011 Peterbuilt! ;)
But as in many vehicles when the blower only works in high its due to a bad blower resistor. The resistor is in operation on slower speeds and the motor gets full power and bypasses the resistor on the high speed setting.

As for where it is on a Peterbuilt, again I don't o0wn one so I can't say for sure.
It should be located near the blower motor as it uses the fan blades air to keep it cool.

Oct 04, 2011 | Cars & Trucks

1 Answer

My 2002 Grand Prix sounds fine upon starting. When I get to 45 mph, it starts to sound as if it's working harder. It's like a loud hum starts and gets louder as it goes up to 60 mph. As I decrease...


Front Wheel Bearing Hub

You will have to remove the brake calipers,hang it,&
remove the rotor,then you can turn the hub & feel the
roughness.

ROCK AUTO.com for parts & look at that hub, so you
match it up the same. Don't get in love with one brand
you like, if the hub looks different at the back where the
speed sensor goes in

You also may find your self buying a torx socket or metric
socket driver to get the speed sensor out. Maybe not

If tools are needed,do yourself a favor & step inside a Snap-On
Truck & just buy one item or so. If you don't ,you won't find those
items anywhere

Sep 21, 2011 | 2005 Pontiac Grand Prix

2 Answers

Windshield wipers work but interminent settings don't


most likely cause is the wiper switch has gone bad and unable to 'time' the intermittent speeds.the intermittent speeds work on a resistor type system where low and high speeds add direct voltage.

Jul 30, 2011 | 2000 Toyota Avalon

Not finding what you are looking for?
Cars & Trucks Logo

285 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

fordexpert

Level 3 Expert

5546 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...