Question about 1995 Pontiac Sunfire

Open Question

Procedure for fixing a valve lifter in 95 pontiac sunfire

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1201 Answers

SOURCE: pontiac sunfire valve noise

If it's a ticking noise that speeds up with the speed of the engine, it's a worn valve lifter.
You can try tightening it down by taking the valve cover off and tightening the bolt on the rocker arm, but don't tighten it too much, you will end up with other problems.

Posted on Jul 11, 2009

Ad
  • 12650 Answers

SOURCE: 95 mustang valve train noise.. coming from top of

not hard and no dont need to remove intake will have to remove some things depends on which side your working on like air intake hose a wire or two might have to unbolt a/c/ if u have- could be rocker also check for dry push rod ,weak valve springs worn valve guide-

Posted on Nov 04, 2009

  • 1149 Answers

SOURCE: Were is the thermostat located in a Pontiac Sunfire 2000?

Hi:
Your thermostat is located under the thermostat housing, which is what the upper radiator hose clamps to on the top of your engine. Basically, you need to start with a cold engine, drain your radiator, then unclamp the upper radiator hose from the engine. Remove the bolts from the thermostat housing, and gently tap on it to remove it. clean up the mounting surfaces on both the engine and the housing, and install a new thermostat, and new gasket. tighten to proper torque, reconnect the radiator hose, then refill up the radiator and cooling system.

Posted on Nov 24, 2009

Testimonial: "Thank you, very helpful"

dnewcombe1
  • 1564 Answers

SOURCE: my heat wont work on a 95 pontiac sunfire changed

Before you get too deep into this, there's one common problem for GM products. Under the hood near to the passenger side of the firewall, there is a large black plastic ball with two vacuum lines protruding from one end. Check these lines very well from the ball to the manifold. I think you'll find your problem there. Thanks, Dana

Posted on Jan 06, 2010

  • 40 Answers

SOURCE: i have a 95 pontiac sunfire, it died on me a lil

Your, car has a crankshaft sensor that, may not working.
Check, the sensor, it is located ( Near the Crankshaft,) You'll
need to look from under the car.
Or It may just NOT have a good connection.
Wet, DIRT bad connection rust on connector.

Posted on Jan 24, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2003 pontiac sunfire makes clanking sound from engine, sounds like valves? lifters make more of a ticking sound...right?


valves do not normally make a sound unless the seat insert is loose in the head. This will be revealed by a compression test. I suspect that a clanking sound is much lower in the engine --like a big end failure.

Feb 18, 2015 | 2003 Pontiac Sunfire

1 Answer

Ive got a 00 sunfire with a 2.2 its got over 200 thousand on it, the lifters were bad n i just changed them but its still ticking so i pulled the valve cover off and pin pointed the the ticking, its coming...


look at ur old lifters u may have a flat,burnt or bad spot on cam also check valves may be carboned, burnt or even slight bend and push rods same can be clogged ,bent etc,it does take a few to prime lifters- usually u can prime them before install with an oil can

Apr 15, 2013 | Pontiac Sunfire Cars & Trucks

1 Answer

How do I replace a 1995 Pontiac Sunfire's rear license plate lamp


I haven't worked on a '95 sunfire in many years but if memory serves me correctly the light is a sealed unit. The best bet is to get a replacement at the local auto parts store and use it as a model to guide you.

Jun 06, 2010 | 1995 Pontiac Sunfire

1 Answer

The pushrods were removed and not kept in order. where can i get a diagram?


Keeping the pushrods in order on an engine isn't because of certain ones being longer than others. Pushrods develop an unique wear pattern with the lifter, and if you change them around, they won't seal anymore, and won't carry oil to the top of the valve train. This will result in your valve guides wearing out prematurely, and causing excessive wear. If they haven't been kept in order, you should replace the lifters and pushrods.

Mar 23, 2010 | 2000 Pontiac Sunfire

1 Answer

How to adjust valve clearance on a 1999 sunfire 2.2L engin. I heard noise in my engine and I am thinking its only the valve clearance need to be adjust.


There is no valve adjustment for that engine, Hydraulic lifters, You might remove the valve cover and see if you have a rocker arm loose

Mar 13, 2010 | 1999 Pontiac Sunfire

2 Answers

I have a 1996 pontiac sunfire with a 2.2 and my book isnt telling me the valve lash. could you help with that?


it does'nt tell you any spec's because you probly have self adjusting lifters A.K.A hydraulic lifters they pump up and take out the slack .just set the rockers properly and you should be goin again.. but if it is overhead cam and all the rockers are on a shaft then i'm guessing the intake would be around .010 thousandth's and the exaust would be more like .012 thousandths but good luck what ever your playing with .

Jan 20, 2010 | GMC S-15 Cars & Trucks

2 Answers

I had a ticking noise and i adjusted the rocker arm and most of it went away. Could this be the only problem? It is a 96 pontiac sunfire


if high milage motor seems fine leave it as is-not proper way to fix either have worn cam, rocker, or bad lifter. old chevy motors with car running was zero latch no ticking 3/4 to 1 turn to center lifter plunger

Aug 25, 2009 | 1996 Pontiac Sunfire

1 Answer

Pontiac sunfire valve noise


If it's a ticking noise that speeds up with the speed of the engine, it's a worn valve lifter.
You can try tightening it down by taking the valve cover off and tightening the bolt on the rocker arm, but don't tighten it too much, you will end up with other problems.

Jul 11, 2009 | 1999 Pontiac Sunfire

1 Answer

A diagram for 95 pontiac sunfire 2.2l with ac


can u hook up a 2200 1998 sunfire motor in a 1995 sunfire 2,2?

May 09, 2009 | 1995 Pontiac Sunfire

2 Answers

Stalls after it runs awhile,


egr valve is open, have it checked.it might be the egr valve itself or the siolinoid

Jul 22, 2008 | 1995 Pontiac Sunfire

Not finding what you are looking for?
1995 Pontiac Sunfire Logo

Related Topics:

110 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8548 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...