Question about Ford Escort

1 Answer

How do you install a pilot bearing on a 95 Ford Escort? 1.9L 5speed

Posted by on


1 Answer

  • Level 1:

    An expert who has achieved level 1.


    An expert who has answered 20 questions.


    An expert that hasĀ over 10 points.


    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 20 Answers

You must remove the transmission to install this bearing it is located in the center of your flywheel.

Posted on Aug 03, 2010


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Got a 95 ford escort lx hatchback has a squeaking noise only when turning left and pushing the gas?

This can be a C-V joint or hub bearing. If your style of front strut has a tower bearing, that's another possibility.

Mar 08, 2014 | Ford Cars & Trucks

1 Answer

How do I remove and replace the pilot bearing on my 95 GMC Sierra truck.

You first have to remove the transmission, then remove the pressure plate and clutch disc from the flywheel. the pilot bearing in in the center of the flywheel it can be removed by packing the hole with grease then take a piece of round stock that is slightly smaller than the hole and giving it a quick sharp blow with a hammer this should force the pilot bearing out then wipe out the grease and install the new pilot bearing

Nov 29, 2012 | GMC Cars & Trucks

1 Answer

How to replace clutch

are you sure the clutch is bad or is it a hydraulic issue dose the pedal fall to floor after a while stoped or does it slip whil under a load you need to remove tranaxel to replace clutch preasure plate and throw out bearing as well as resurface flywheel check rear main seal andpossibly replace pilot bearing or bushing if it is hydraulic trans axle can stay in and just change slave cyl and or clutch master cyl

Mar 25, 2012 | 1995 Ford Escort

1 Answer

5speed manual when i push clutch in and shift gears it is going in gear ok but every gear sounds like winding got to let off gas to go

Your clutch may not be disengaging fully, perhaps a tight pilot bearing, or a clutch disc that doesn't move freely on the main shaft. Check your lube level in the transmission. refill as needed.

Sep 02, 2010 | 1992 Ford Explorer

1 Answer

My 95 escort gets stuck in fifth gear. Sometimes will come out sometimes wont. Have to stop the car, turn engine off and then pull out of fifth.

If it's a stander transmission, could be pressure plate getting weak, only repair is to replace it with a clutch kit, kit will have disk, pressure plate and bearing.

Jul 22, 2010 | 1995 Ford Escort

1 Answer

New Clutch, New Noise!

throw out baring was inproperly installed

Mar 30, 2009 | 1998 Ford Escort

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

119 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts


Level 3 Expert

81294 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

gerry bissi

Level 3 Expert

4376 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides