Question about 1995 Mercury Villager

1 Answer

My Villiager won't get into gear right away and the rpms go all the way up to 3.5 or 4. what could it be? Sue

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

Your traanny is slipping

Posted on Aug 06, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Can't find crank sensor on 94 mercury villiager


The van uses a distributor, and the crank sensor is inside the distributor.

Jul 03, 2013 | Cars & Trucks

1 Answer

Won't shift into 5th gear or over drive.


Change the trans solenoid pack inside the transmission pan

One part--- contains 3 pressure solenoids & all 4 shift solenoids

Feb 17, 2013 | 2000 Lincoln LS

1 Answer

1998 Z3.. Manual Trans shudder under acceleration in 2nd gear as it nears 2000 rpms, then goes away as it approaches 2500 rpm's.. Any suggestions?.. Thanks


It could either be the flex disc or drive shaft center bearing. I had the same problem on my 98 Z3 and I replaced both and it took care of the problem.

Aug 31, 2012 | 1998 BMW Z3 Roadster

1 Answer

I have a Jaguar X-Type 2.5L and the check engine light is on as well as the other light on the board. It also says in the screen that the cruise is not available however It is functional. The problems are...


need to run a scan with a data stream-to diagnose--just pullin up codes doesnt doit--also are the fluids new and at correct level--if theyr dirty or old things are slower to work--clean the throttle body and idle air motor to stop stalling--chec for worn ignition components

Mar 28, 2012 | 2003 Jaguar X-Type

1 Answer

1995 Dodge ram 1500 V-8 5.9 litre 4x4 short bed is feels like it is bumping when the truck shifts into cruising gear and RPMs drop truck smmoths out when you speed up bumping goes away if you shift...


Perform compression check between cylenders #1 and #3. These are right next to each other.
You might get away with a head gasket replacement, if the compression between these cylenders is the same, indicating a blown head gasket between cyl.#1 and #3 not valves which will give different readins between these cylenders.

Nov 29, 2009 | 1996 Dodge Ram 1500 Club Cab

2 Answers

2001 Dakota Quad Cab Runs Rough


Your friend may be right,The Dakota made from 1997 to 2003 all had issues with the catalytic converters going bad,I have a 2001 and have had to get mine replace 3 times already.

May 11, 2009 | 2003 Dodge Dakota Club Cab

1 Answer

Transmission wont shift until about 4000rpms from 1st to 2nd gea


Have a code check done and see if speed sensor or controller is working properly. if bought from a dealer, get it back there asap...they can't sell it in that condition!!...No test drive before you ploped down your money?

Apr 16, 2009 | 2004 Jeep Grand Cherokee

Not finding what you are looking for?
1995 Mercury Villager Logo

Related Topics:

48 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts

gerry bissi

Level 3 Expert

4376 Answers

Marvin
Marvin

Level 3 Expert

81423 Answers

fordexpert

Level 3 Expert

5687 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...