Question about 1985 Chrysler New Yorker

1 Answer

85 New Yorker Turbo 4 Cylinder Have all the bolts and wires are removed from starter but unable to remove it. Suggestions?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Guru:

    An expert who has written 7 tips or uploaded 3 video tips

  • Master
  • 642 Answers

3 bolts holding the starter at the bellhousing end. Another 1 on the rear of the starter. Battery cable removed from solenoid. Pull back on the starter then tilt the rear down and it should come out. If it does not move at all I suspect you missed the bolt closest to the block. Whenever working on the starter make sure the battery negative is disconnected.

Posted on Aug 02, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to install a clutch kit on my 1994 mitsubishi mighty max


Disconnect the battery, disconnect the Hydraulic Line from the Slave Cylinder, Remove the Starter (2 bolts, 2 wires. Bolts are 14mm, 1 wire is 12mm, 1 plugs in), Remove the Driveshaft(s) (4 12mm bolts) Remove the 6 bolts from the bellhousing (4 are 14mm, 2 are 10mm)
Remove the bolt from the Transfer Case Mount, 12mm (only if it's a 4WD, if it's 2WD this doesn't apply), remove the 2 bolts that hold the Transmission Mount to the Crossmember (12mm or 14mm, it varies)
Slide the transmission back on the crossmember, away from the engine, I recommend running a ratchet strap across the frame to balance the transmission.
Remove the Pressure Plate from the Flywheel (Six 10mm bolts), Inspect the Pilot Bearing (if it needs replaced, you'll need to remove the Flywheel which is held on with six 18mm bolts, drive out the old bearing and drive in the new one, reinstall the flywheel, using Threadlocker on the bolts, torque the bolts to 100 ft lbs) Install the new clutch disc and Pressure Plate, with the centering tool inserted through the disc into the pilot bearing. Use thread locker on the pressure plate bolts and torque them to 20 ft lbs. Remove the centering/alignment tool after you've bolted it together
Remove old Throw Out bearing from input shaft on the transmission and slide the new one on. Slide the Transmission forward (make sure the input shaft slides into the pilot bearing, don't force the transmission into place or you could damage the clutch disc or break the input shaft) Torque the Bellhousing Bolts to 40 ft lbs (4 14mm bolts), Torque the 2 10mm bolts to 14 ft lbs, Install the Starter (torque bolts to 23 ft lbs), Reconnect Hydraulic Line to Slave Cylinder. Torque Transmission Mount Bolts to 30 ft lbs.
Reinstall Driveshafts, torque bolts on flange/yoke to 40 ft lbs. Fill Clutch Master Cylinder with DOT-3 Brake & Clutch Fluid, Open Bleeder Screw on Slave Cylinder and bleed the air out of the system, close bleeder screw.
Reconnect the wires to the Starter, Reconnect the battery.

Aug 24, 2011 | Mitsubishi Mighty Max Cars & Trucks

2 Answers

How to remove a starter in 1987 ford taurus?


Underneath the car, for a front wheel drive, it will be toward the front of the engine a long cylinder shaped part with another cylinder with wires going onto it. take the wires off first, paying close attention to their placement, then you remove the mounting bolts and pull it out, it's that easy dude, you can also find a video on how to do it on youtube.

Jun 09, 2011 | 1987 Ford Taurus

1 Answer

Where is the starter on a 1991 eclispse 2l awd turbo


Hope this helps, it it does please leave feedback and vote Thank You and Good Luck

Removal


  1. Disconnect battery cables, then remove battery and battery tray.
  2. Disconnect speedometer cable from transaxle.
  3. On models equipped with 1.8L/4-107 engines, remove intake manifold stay.
  4. On all models, disconnect starter wiring connections.
  5. Remove starter mounting bolts, then the starter.
Installation


  1. Before mounting starter, clean the mating surfaces of starter and the engine.
  2. Install starter and torque mounting bolts to 20-25 ft. lbs.
  3. Connect starter wiring connections.
  4. On models equipped with 1.8L/4-107 engines, install intake manifold stay.
  5. On all models, connect speedometer cable.
  6. Install battery tray and torque attaching bolts to 6-10 ft. lbs.
  7. Install battery and battery hold-down. Torque hold-down bolts to 1.5-2.0 ft. lbs.
  8. Connect battery cables.

Jan 02, 2011 | 1991 Mitsubishi Eclipse

1 Answer

Change out starter


Starter - 4 Cylinder 112139431
  1. Release hood latch and open hood.
  2. Disconnect and isolate the battery negative cable.
  3. Remove the air cleaner box.
  4. Remove the lower bolt.
  5. Remove the upper bolt and ground wire
Starter Removal - 4 Cylinder 112139432
  1. Remove starter.
  2. Disconnect solenoid wire connector from terminal
  3. Remove nut holding B+ wire to terminal.
  4. Disconnect solenoid and B+ wires from starter terminals.

Jan 01, 2011 | 2004 Dodge Stratus

1 Answer

Replacing a starter on a 1993 volvo 940 turbo. Is this a difficult task?


It looks easy for the 940 but I am not sure about the 940 turbo, as maybe some of the turbo parts are in the way. I'm not sure about that, since there is no documentation on the turbo model vs. the 940 standard model. If you can follow the following instructions, then I would give it a whirl.

REMOVAL & INSTALLATION - 1993 Volvo 940
  1. Disconnect the negative battery cable at the battery.
  2. Disconnect the leads from the starter motor.
  3. Remove the starter motor retaining bolts.
  4. Remove the starter motor from the vehicle. To install:
  5. Position the starter motor to the flywheel housing.
  6. Apply locking compound to the bolt threads and install the retaining bolts finger-tight.
  7. Tighten the bolts to approximately 25 ft. lbs. (34 Nm).
  8. Connect the starter motor leads and the negative battery cable. Fig. 1: Unfasten the nut retaining the starter cables . . . 90952p12.jpg
    Fig. 2: . . . and remove the starter cables 90952p14.jpg
    Fig. 3: Unfasten the starter retaining bolts . . . 90952p11.jpg
    Fig. 4: . . . and remove the starter from the engine 90952p15.jpg
prev.gif next.gif

Oct 28, 2010 | 1993 Volvo 940

1 Answer

Replacing a new starter on a 93 isuzu rodeo


Don't know what size motor you have because you didn't post it so please pick the proper one:

This is for the 4 cylinder motor--

8e64f3e.gif
4-cylinder engine starter connections



  1. Disconnect the negative battery cable.
  2. Raise and safely support the vehicle on jackstands.
  3. If equipped, it may be necessary to disconnect and remove the EGR pipe to access all the starter bolts.
  4. Tag and disconnect the starter battery and control wiring at the starter.
  5. If equipped, remove the starter bracket and/or heat shield.
  6. Remove the starter-to-engine bolts.
  7. Move the starter away from the engine and down to remove from the vehicle. Some starter may be installed with shims between the starter and engine. When the starter is removed, these shims may fall out. Do not loose them.
To install:
  1. Install the starter and shims, if equipped to the engine. Align the mounting bolt holes and insert the bolts. Hand-tighten the bolts.
  2. Tighten the starter mounting bolts to 30–34 ft. lbs. (39–44 Nm).
  3. Install the starter bracket and/or heat shield, if equipped.
  4. Connect the battery and starter control electrical wires to the starter.
  5. If the EGR pipe was removed, install it.
  6. Lower the vehicle.
  7. Connect the negative battery cable.
  8. Start the vehicle to make sure the starter functions correctly.
This is for the V6 motor--

8fdc27b.gif
6-cylinder engine starter installation


  1. Disconnect the negative battery cable.
  2. Raise and safely support the vehicle on jackstands.
  3. Label and disconnect the battery and starter control wires from the starter.
  4. If equipped, remove the starter bracket and/or heat shield.
  5. Remove the starter-to-engine mounting bolts.
  6. Lower the starter from the engine. If any shims are present, keep them for reinstallation purposes.
To install:
  1. Install the starter and shims, if equipped, to the engine. Tighten the mounting bolts to 30–34 ft. lbs. (39–44 Nm).
  2. Install the starter bracket and/or heat shield, if equipped.
  3. Reconnect the electrical connectors to the starter.
  4. Lower the vehicle.
  5. Connect the negative battery cable.
  6. Start the vehicle to make sure the starter functions correctly.

Nov 19, 2009 | 1993 Isuzu Rodeo

1 Answer

85 new yorker 2.2 cant find paint code


Have you located plate with all the numbers on it yet? Usually on firewall, or below windshield,or upper rad support area.

Aug 24, 2009 | 1985 Chrysler New Yorker

3 Answers

Starter for 2004 honda accord


Is this for a 4 or 6 cylinder engine?

If it is for the 4 cylinder, it's not that easy as the intake manifiold needs to be removed before the starter can be removed as the starter is under the intake manifold. Once the manifold is removed then it's a matter of a couple bolts and connections. It's not that quick a job.

Aug 19, 2009 | 2004 Honda Accord

2 Answers

I am trying to locate the starter of my 1998 LS 400 pls. help me.


The starter is located under the intake manifold on this engine.

20d8b81.gif

Jun 17, 2009 | 1998 Lexus Gs 400

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

31 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

76051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8265 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...