Question about 1998 Chevrolet Lumina

1 Answer

I just bought a 1998 lumina with manual front seats. but the seats will not slide back. any suggestions?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 3,301 Answers

Look under the seat to see if the cable that connects the 2 sides is ok,,

Posted on Aug 02, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to remove a front seat on a 1998 cutless


Most seats are attached to the floor by bolts.
- Slide seat all the way forward and remove rear bolts
- Slide seat all the way back and remove the front bolts.
- Unplug any wires.
- Remove seat.
This process will involve looking under the seat so a kneepad and flashlight may make it easier.

Oct 22, 2015 | Seat Cars & Trucks

1 Answer

Remove diver seat from 1998 lincon town car.


slide the seat all the way forward , this should reveal the bolts at the rear ,once removed slide seat all the way back then undo the front bolts

Jul 05, 2014 | 1998 Lincoln Town Car

1 Answer

Removing a driver seat of a 1998 Buick Century


Usually the seat is bolted to the floor in the back. Slide seat all the way forward, look for 2 15mm bolts. take out bolts, tilt seat up, disconnect wires, then slide seat back out of front slots.

Aug 11, 2013 | Cars & Trucks

1 Answer

How do you remove the drivers seat in a '98 Jetta? I want to replace it. Thanks


slide the seat right forwards and you will see, inside the runners,the bolts to remove,the runners,with the seat...after the rears slide the seat right back to see the front bolts.replacement is a reversal of removal......

Oct 30, 2010 | 1998 Volkswagen Jetta

1 Answer

Remove front seat


SECTION 501-10: Seating 1998 Escort/Tracer Workshop Manual REMOVAL AND INSTALLATION Seat —Front Removal
NOTE: Driver side seat shown, passenger side seat similar.
  1. Slide the seat to its rearward position.
  1. Remove the front seat track to floor front bolts.
  1. Slide the seat to the forward position.
  1. Remove the front seat track to floor rear bolts.
  1. Disconnect the safety belt warning indicator switch electrical connector.
  1. Remove the front seat.

Dec 06, 2009 | 1998 Ford Escort

1 Answer

Replace front disc pads on 1998 lumina


Visit the autozone.com website and register the car information. It's free and will give you access to an online repair manual for the car. The steps for replacing the brake pads should be available there. It's a handy resource. Hope this helped and best wishes.

Sep 11, 2009 | 1998 Chevrolet Lumina

1 Answer

Driver's seat in a 1998 chevy lumina has broken free from left front support. Need to remove and install new used seat. (power seat)


so whats your question? Just unplug it from the harness, unbolt it from the floor panel, and make the switch, if your using another factory seat from the same year vehicle.

Sep 10, 2009 | 1998 Chevrolet Lumina

1 Answer

How do i remove the front seats of a 1998 Pontiac Grand Prix?


On W-Body vehicles, the front seats are secured to the floorpan by two front hook attachments and two rear bolts installed to nuts welded to the floorpan.
The manually operated two-way front adjusters provides only fore and aft movement of the seat. When the seat adjuster handle located on the front seat is pulled up, the seat adjusters unlock, permitting travel of the seat. When the seat is in the desired position and the seat adjuster handle is released, the seat locks in place.
A power operated six-way seat adjuster is available. The adjusters are activated by three 12 volt, reversible, permanent magnet motors with a built-in circuit breaker. The motors are energized by a switch bolted on the seat side panel.
The three motors drive the front seat and rear vertical actuators and a horizontal actuator. When the adjusters reach the limit of travel, torque is absorbed through the rubber mounted grommets located between the motor and the support. An overload relay is provided in the circuit and will open should excessive stall be applied.
The optional 60/40 split bench front seats have seat back head restraints on the driver's and passenger's seat back. The head restraints are designed so they cannot be removed from the seat back without first inserting a small rounded tool inside the head restraint support tube to release the locking tab. The 60/40 split bench seat is equipped with a reclining mechanism on both the driver's and passenger's side. The recliner lever is located on the outboard side of the spring cushion. When the lever is pulled upward, the spring loaded dual linear reclining unit located in the cushion frame is released, allowing the seat back to be pushed rearward or allowing the spring loaded reclining unit to bring the seat back forward.
Bucket seats are equipped with manual reclining mechanisms. An optional six-way power seat adjuster is available. Some bucket seats are equipped with inertia seat back locks. This system allows the seat back to fold forward without requiring the occupant to release a locking lever or access to the rear seat area. During a sudden stop or deceleration, or if the front of the vehicle is nose down, the inertia system of the seat back lock will engage, holding the seat back in its rest position. A release lever is provided to allow manual release of the seat back lock when the vehicle is in the nose down position. The release lever is located at the lower rear outboard corner of the seat back.
Some W-Body vehicles (notably Pontiac coupes) have passenger front seats equipped with an E-Z Entry device. This is actuated, in an unoccupied seat, by completely folding the seat back forward disengaging the adjuster, and sliding the front seat forward to gain access to the rear seat area. To return the seat to its normal position, return the seat back to its rest position, and slide the entire seat rearward, engaging the adjuster.
W-Body rear seats are available in several styles including a rear seat with an integral child restraint device.

Sep 01, 2009 | 1998 Pontiac Grand Prix

1 Answer

How to remove the back seat from my 1998 Mercury Villager


it is not designed to be removed. It is designed to slide back and forth as needed.

Section 01-10: Seats and Tracks 1998 Villager Workshop Manual
REMOVAL AND INSTALLATION Seat, Rear Bench
Removal
  1. Remove the center seat(s) if equipped. Refer to the procedure in this section.
  1. Slide the bench seat forward to the center row seating position.
  1. Use a flat-blade screwdriver to remove the cover caps from the front of the rear seat cushion latch cover.




  1. Remove the two rear seat bolts from the front of the rear seat cushion latch cover.




  1. Lift the rear seat cushion floor cover on the back of the rear bench seat and remove the two inboard rear seat bolts and the two outboard rear seat bolts.




  1. Remove the bench seat from the vehicle through the body side door opening.

Apr 30, 2009 | 1998 Mercury Villager

Not finding what you are looking for?
1998 Chevrolet Lumina Logo

Related Topics:

48 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

78267 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...