Question about 1993 Ford Aerostar Extended

Open Question

Parking brake on our '93 Ford Aerostar is too tight in resting position. How can that be adjusted?

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
tepfy
  • 319 Answers

SOURCE: 93 Ford thunderbird parking brake adjustment

on most of the cars us use a special spanner tool that resembles a bent screwdriver. you pull the plastic cap out from the back of the drum and then just turn the ajustment wheel till you feal it tighten up a litle. Remember to put the plastic cap back on. Also a old trick most people don't know about is put the car in reverse in a parking lot, and slam on the brakes. most cars have a auto ajustment that they never use.

Posted on Sep 10, 2008

Ad
michigan man
  • 3533 Answers

SOURCE: parking brake is stuck on

need to get the truck on jack stands remove the wheels and if the truck has drums you maybe able to use some PB blast because the brake cables are rusted for the emergency brakes and at the same time you can check out the condition of your shoes or pads if you get any oil on the shoes or pads use brake cleaner to clean them off

Posted on Jan 25, 2009

  • 130 Answers

SOURCE: How do I adjust the parking brake?

Loosen the cable nut at the rear brake, pull the cable until the tension is tight, then tighten the cable nut. Since the parking brake only operates on the rear brakes, your rear pads may be too worn causing the parking brake not to hold. Check the pads first to see if they need to be replaced. Also, the parking brake cable can stretch or break over time. Verify that isn't case since you may need to install a new cable rather than adjust it.

Posted on May 03, 2009

  • 314 Answers

SOURCE: I need to adjust my parking brake on my 2003

there should be an adjusting screw around the lever that is used to apply the parking brake. if you tighten this until there is a slight drag in the back tires and then back off two full turns then that will adjust the parking brake.

Posted on Jun 25, 2009

  • 3600 Answers

SOURCE: Parking brake doesn't work

Follow the brake cable near the rear brakes and where the Y is loosen the locking nut and then unscrew the Y so that it is loose, that is turn the nut counter clockwise to loosen both sides f the cable. Also check that the E brake cables are not broke inside of the cable housing.

Posted on Sep 07, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Parking brake


Adjust the cable tightness is the first step, the adjustment is at the handle a nut on a threaded rod which is the end of the parking brake cable. Turn the nut in until the brake starts to engage after 3 clicks.

Aug 24, 2012 | 1990 Ford Escort

1 Answer

How to installing brake shoes on back ?


First you have to compress the parking brake cable spring and attach the parking brake lever.
Clean and lubricate the brake backing plate.
Use silicon Brake Caliper Grease and Dielectric Compound.
Then,
install the rear brake shoes and linings:
1) position the rear brake shoes and linings
2) position the parking brake lever
3) install the brake shoe hold-down spring pins and the brake shoe hold-down springs.

Install the parking brake strut
1. install the parkig brake link spring on the parking brake strut
2. install the parking brake strut
3. Install the brake shoe anchor ping guide plate.

Install the short brake shoe retracting spring
1. Place the brake shoe adjusting lever cable over the anchor pin, with crimped side in
2. Install the short brake shoe retracting spring

Note: Make sure the brake shoe adjusting lever cable is positioned in the cable guide groove

Install the long brake shoe retracting
1. install the cable guide
2. position the brake shoe adjusting lever cable in the cable guide groove
3. install the long brake shoe retracting spring

Note: to prevent incorrect installation, teh socket of each brake adjuster screw is stamped R or L

Assemble the brake adjuster screw assembly.
1. apply silicone brake caliper grease and dielectric compound
2. install the brake adjuster screw into the brake show adjusting screw nut to the end of the threads and then loosen one half turn
3. install the brake shoe adjusting screw socket on the brake shoe adjusting screw nut.

Install the brake adjuster screw assembly
1. Position the brake adjuster screw assembly
2. Install the brake shoe adjusting screw spring
3. Position the brake shoe adjusting lever cable
4. Position the adjusting lever return spring and the brake shoe adjusting lever
5. Hook the brake shoe adjusting lever cable to the brake shoe adjusting lever.

Test the operation of the automatic self-adjuster
1. Pull the brake shoe adjusting lever cable and check that the brake shoe adjusting lever rotates the brake shoe adjuster assembly
2. Release the brake shoe adjusting lever cable and check that the brake shoe adjusting lever advances to the next notch on the brake shoe adjusting screw nut.

Adjust the brakes.

Install the brake drum.

Thats it

Sep 10, 2010 | 1998 Ford Ranger SuperCab

1 Answer

How do I adjust the parking brake cable on a 1993 Ford Aerostar XLT


you dont ,these cables will not stretch unless used to tow a ten ton truck out of a ditch ,look at the brakes themselves and adjust the shoes up and do the job properly

Jul 03, 2010 | 1993 Ford Aerostar Extended

1 Answer

How do you adjust the parking brake on a 1994 ford ranger,manaul trans,4wd


Start by adjusting up the rear brakes, if those are tight and you still want to tighten up the parking brake running down the driver's side, outside the frame are the parking cables. somewhere around the back of the cab/front of the bed should be a plate with 2 cables and a bolt. tighten the bolt/nut up to make the parking brake tighter

Oct 04, 2009 | 1994 Ford Ranger Supercab

2 Answers

93 ford aerostar brake problems


the brake master cylinder has failed, replace it.

Jul 20, 2009 | 1993 Ford Aerostar Extended

1 Answer

I need to adjust my parking brake on my 2003 Expedition. It does not hold as tightly as it use to. Is this something that can be easily adjusted?


there should be an adjusting screw around the lever that is used to apply the parking brake. if you tighten this until there is a slight drag in the back tires and then back off two full turns then that will adjust the parking brake.

Jun 25, 2009 | 2003 Ford Expedition

1 Answer

NEED A DIAGRAM ON HOW TO BLEED THE BRAKES ON A 93 AEROSTAR VAN


try these websites www.autozone.com or www.alldatadiy.com and you should be able to get diagrams and pictures showing you how to repair your car

May 22, 2009 | 1992 Ford Aerostar Extended

1 Answer

How do I adjust the parking brake?


Loosen the cable nut at the rear brake, pull the cable until the tension is tight, then tighten the cable nut. Since the parking brake only operates on the rear brakes, your rear pads may be too worn causing the parking brake not to hold. Check the pads first to see if they need to be replaced. Also, the parking brake cable can stretch or break over time. Verify that isn't case since you may need to install a new cable rather than adjust it.

Apr 30, 2009 | 2000 Ford Explorer

2 Answers

Handbrake does not always work at first attempt. if you pull the handbrake up and down a few times without the button pressed eventually it catches on the ratchet and works.


Check the return spring on the parking brake lever as wll as the gear teeth:
  1. Make sure the parking brake cable is free and is not frozen or sticking. Make sure the brake shoes are properly adjusted.
  2. Raise and safely support the rear wheels.
  3. Apply the parking brake while counting the number of notches. Check the desired parking brake stroke; it should be 7-9 notches.
  4. If adjustment is required, remove the adjusting nut cover and turn the adjusting nut located at the front of the parking brake cable.
  5. After adjustment, check there is no looseness between the adjusting nut and the parking brake lever, then tighten the locknut.
Do not adjust the parking brake too tight. If the number of notches is less than specification, the cable has been pulled too much and the automatic adjuster will fail or the brakes will drag.
  1. With the parking brake lever in the released position, turn the rear wheels to confirm that the rear brakes are not dragging.
  2. Lower the vehicle.
  3. Check that the parking brake holds the vehicle on an incline.

Sep 24, 2008 | Mazda MAZDA6 Cars & Trucks

1 Answer

93 Ford thunderbird parking brake adjustment


on most of the cars us use a special spanner tool that resembles a bent screwdriver. you pull the plastic cap out from the back of the drum and then just turn the ajustment wheel till you feal it tighten up a litle. Remember to put the plastic cap back on. Also a old trick most people don't know about is put the car in reverse in a parking lot, and slam on the brakes. most cars have a auto ajustment that they never use.

Jun 14, 2008 | 1993 Ford Thunderbird

Not finding what you are looking for?
1993 Ford Aerostar Extended Logo

Related Topics:

65 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5522 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...