Question about 2002 Nissan Sentra

1 Answer

What is the torque for the torque converter to flywheel

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Nissan Master
  • 81,400 Answers

35 foot pounds

Posted on Aug 02, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I bought a new 22re crate motor because the other one was blown, hole in side of block.went to marry engine to transmission and I know for sure that the torque converter is seated all the way.so my...


never knew that a torque bolted to a flywheel, it is always bolted to a flex plate that drives the torque converter and carries the ring gear for the starter
there are washers that fit either of that flex plate or on some engines only on the converter side with the bevelled edge facing away from the plate
the torque converter is bolted to the flex plate by 3 or 4 bolts facing back to the converter from the block end
why are flywheels not used with torque converters
the mass of the flywheel affects the engine acceleration and the torque converter full of oil takes over that job so the engine acceleration would be considerable slower if both were used

Nov 26, 2017 | Cars & Trucks

1 Answer

Looking for cylinder head, main bearings, big end bearings and flywheel torque settings. Also valve clearence for same engine.


go google and type in - torque settings for (your engine as you haven't given that infomation) and there will be pages of details
There is no flywheel for an automatic. What you have is a flex plate as the torque converter acts as a flywheel

Mar 18, 2015 | Cars & Trucks

2 Answers

How many ft/lbs of torque is recommended on the flywheel bolts when installing the flywheel on a 1996 GMC Sierra Z-71 4x4 5.7L engine?


GMC Sierra Bolt Torque Specifications. ... The torque converter bolts to the flywheel with 46 foot-lbs. of torque. ... 1996 GMC Sierra Horsepower Torque Specs.

May 02, 2014 | Cars & Trucks

1 Answer

Flywheel rubing on engine


either flywheel is installed backwards or you forgot the shim that goes between flywheel and crank

Aug 02, 2013 | 1999 Mitsubishi Galant

1 Answer

2001 tiburon


Torque converters are bolted up to the flywheel or flexplate. Probably 4 or 6 bolts from the flywheel engine side into the torque converter.

May 03, 2012 | 2001 Hyundai Tiburon

2 Answers

Where is tork converter bushing


In the back of the crankshaft in the center of the flywheel.

Jan 05, 2011 | 1999 Isuzu Rodeo

1 Answer

How do you change the flywheel?


Pull the transmission back (or remove) enough to access the flywheel/ torque converter. Remove the converter from the flywheel, then you will see the flywheel bolts that mount the flywheel to the crankshaft--(I think there are 6). It is advisable to replace these bolts with new ones when reinstalling the flywheel, and be sure to get the proper torque spec for the bolts from autozone or a reputable shop and torque them sequencially correct and to the proper spec.

Oct 03, 2010 | 1982 Chevrolet El Camino

1 Answer

Is the flywheel part of the torque converter?as in connected to it?


Actually...
an automatic transmission does not use a flywheel; the torque converter is heavy enough to provide the inertia necessary.
The torque converter connects to the flex plate and the flex plate connects to the crankshaft. On an automatic transmission, the flex plate is the part that has the starter gear.

Aug 30, 2010 | 1989 Chrysler Fifth Avenue

1 Answer

Torque settings for volvo 740 torque converter and flywheel


torque converter housing -- engine, (M10) 26-37 ft/lb (M12) 41-66 ft/lb
Drive plate -- torque converter 30-37 ft/lb
Torque converter housing -- gearbox housing (4 x M-10) 20-31 ft lb
(2 x M-12) 34-50

Apr 05, 2010 | 1989 Volvo 740

3 Answers

Does a torque converter for a 1989 ford bronco trwo have antyhing to do with a fly wheel


the torque converter bolts to the drive plate that supports the ring gear

Mar 24, 2010 | 1989 Ford Bronco II

Not finding what you are looking for?
2002 Nissan Sentra Logo

Related Topics:

53 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

Marvin
Marvin

Level 3 Expert

81400 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22359 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...