Question about 2004 Hyundai Santa Fe

2 Answers

Gas tank has a plug with 5 wiers on it by the fuel pump. I need to know where these wires go, they are colored. connector looks like a triangle

Posted by on

  • Ricky Johnson
    Ricky Johnson Aug 02, 2010

    2004 sante fe 2.7l, there is a plug on top of fuel tank has 5 wires to it. 2-black,red,pink, blue all wires got unplugged when tank was removed. plug has numbers 1-5 on it. need to know what colored wires go where. plug looks like a triangle 3 2 1
    4 5

×

Ad

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 10,515 Answers

Hi,

I have the complete diagram for you,Take a look at :-

gas tank has a plug - a1c8661.jpg

I have already upload the same on mediafire . Download the larger picture from :-

http://www.mediafire.com/?saiu47daa4kw4en

Good Luck!!

Thanks!!

Posted on Aug 02, 2010

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Hyundai Master
  • 17,970 Answers

What engine size are there? 2.7L or 3.5L ?

Posted on Aug 02, 2010

  • 1 more comment 
  • Ricky Johnson
    Ricky Johnson Aug 02, 2010

    engine is 2.7 liter wires are 5 colors. plug has 1-5 listed by wach plug

  • ZJ Limited
    ZJ Limited Aug 02, 2010


    I find this wiring diagrams (click for zoom)...




    Fig. Data Link Detail Schematics, Page 01 (2004)





    Fig. Data Link Detail Schematics, Page 02 (2004)






    Fig. MFI Control System (V6 2.7L) Schematics, Page 01 (2004)





    Fig. MFI Control System (V6 2.7L) Schematics, Page 02 (2004)





    Fig. MFI Control System (V6 2.7L) Schematics, Page 03 (2004)





    Fig. MFI Control System (V6 2.7L) Schematics, Page 04 (2004)





    Fig. MFI Control System (V6 2.7L) Schematics, Page 05 (2004)



    Hope helps.

  • Ricky Johnson
    Ricky Johnson Aug 02, 2010

    i need to know what colors go to each plug in list as 3 2 1

    colors are red, 2 black, pink with blk strip, purple, 4 5

    they have 3 orange and 2 blue seals when they plug in

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Gas gauge wont work


Replace the sender unit in the gas tank. Some units , you can get at a parts store. Others, look online.

Feb 11, 2015 | Cars & Trucks

1 Answer

Have a 2000 toyota tundra; when taking off gas tank, tank fell and pulled color wires from 5 pin connector on fuel pump. help to rewire. the connector is number 1, 2, 3, 5,4 but the wires are different...


A $20 service manual should include wiring diagrams which will show you color codes. When you buy a manual, make sure it has diagrams. murf427

Aug 30, 2012 | 2000 Toyota Tundra

1 Answer

2004 grand prix check gas cap light on changed gas cap and still the same problem dont know what to do


Open the trunk, pull the carpet back to reveal the access to the fuel pump. The gas tank pressure sensor is located on top or the fuel pump. The connector has 3 wires, 1 black and 2 colored. Pull the plug off the sensor, put jumper across the 2 colored wires, tape it up with electrical tape. Replace the access cover, the carpet, close the trunk and never see that "CHECK GAS CAP" message again.

Sep 26, 2011 | 2004 Pontiac Grand Prix

1 Answer

Need 2 know how 2 remove gas tank so i can replace fuel pump


TO REMOVE FUEL TANK FIRST YOU NEED TO MAKE SURE FUEL SYSTEM BEEN DEPRESSURIZE. YOU CAN REMOVE FUEL PUMP RELAY LET CAR RUN UNTIL DIES LACK OF GAS. THEN CRANK ENGINE OVER FEW TIMES MAKE SURE ALL GAS OUT OF FUEL LINES. THEN REMOVE FUEL CAP THEN DRAIN FUEL TANK.YOU CAN BUY A SIPHON AT ANY AUTO PARTS STORES, DONT SIPHON GAS WITH MOUTH CAN BE VERY FATAL.ONCE FUEL OUT OF TANK. SAFELY RAISE SUPPORT VECHICLE ON JACK STANDS, MAKE SURE VECHICLE SITTING ON LEVEL SOLID GROUND. LOOK UNDERNEATH VECHICLE REMOVE FUEL FILTER DISCONNECT FUEL PUMP ELECTRICAL WIRE CONNECTOR, THEN REMOVE EVAP CANISTER, VENT SOLENOID, AND VAPOR LINES DISCONNECT FUEL LINES, THEN REMOVE THE LOWER FILLERHOSE GOING INTO FUEL TANK. LOOK AROUND TANK YOU PROBABLY HAVE TO REMOVE HEAT SHIELD AROUND GAS TANK AND REMOVE EXHAUST PIPES IF IN THE WAY. GET A LARGE FLOOR JACK AND THE PLACE A PIECE WOOD ON FLOOR JACK SADDLE.THEN RAISE FLOOR JACK JUST ENOUGH SUPPORT FUEL TANK THEN REMOVE FUEL TANK SUPPORT STRAPS THEN SLOWLY LET DOWN THE FUEL TANK. TO FINISH DISCONNECTING FUEL LINES AND REMOVING FUEL PUMP. BE SURE AFTER YOU DEPRESSURIZE FUEL SYSTEM TURN OFF RADIO AND REMOVE THE NEGATIVE BATTERY CABLE.

Aug 04, 2011 | Chevrolet Cavalier Cars & Trucks

1 Answer

I have a 2003 crown victoria cvpi the fuel gage is not working, i belive that if i knew the color of the positive wire going to /from gas tank i could rewire or repair the fuel gauge problem the car was...


These should be the colors coming out of the plug on the fuel pump.

(GY/RD)signal return
(RD/PK)Fuel tank pressure transducer sensor
(BN/WH)Reference voltage
(YE/WH)Fuel pump/fuel gauge sender
(BN/WH)Fuel pump Power, return
(PK/BK)Fuel pump Power, feed
(PK/OG)Ground

I hope this helps you out.

Mar 14, 2011 | 2003 Ford Crown Victoria

2 Answers

1995 nissan pickup truck fuel problem


Fuel injected or carb? Make sure fuel line itself is clear. Some pumps are designed to self regulate (carb systems) some continually pump and a psi regulator sends back the excess fuel back to the tank (fuel inj systems) If the line is obstructed then pump can't deliver fuel fulltime.

If you think pump is not on consistent, try running a dedicated wire through a switch directly to the pump. If it works then you are looking for an electrical fault going to pump. Good luck.

Mar 10, 2010 | 1995 Nissan Pickup

1 Answer

My gas guage will not work on my 1991 buick riviera what do i need to fix it?


about 98% of fuel gauge issues are the fuel sender in the gas tank. This is part of the fuel pump assembly, and is replaced with the fuel pump. There is another place to check though. The wiring that goes to the fuel sender can get unhooked (possible, but not often happens). The connector is above the gas tank; either way you would have to take the gas tank down. By attaching a rheostat or variable resistor, you can test the wiring and gauge system to see if it works. If it does, then you know that you need to replace the pump to get it working again. If not, then you have wiring issues between the pump and the dash. Hope this is what you're looking for.

Dec 09, 2009 | 1991 Buick Riviera

1 Answer

I own a 2000 chevy blazer with a 4.3 v6 vortec. It will turn over but not start up. I replaced the fuel pump, the fuel filter, the plugs and wires, and the pressure regulator. If i dump a little gas in the...


did you check power and ground at the fuel pump connector?there should be power at two wires at the connector,one should have constant power with the key on and thats for your fuel gage,the other power wire should have it only when cranking or for about 3-5 seconds when the key is turned on,check both of those first and that will let you know that everything is fine all the way forward of that connector,also did u replace just the pump or the whole sending unit?if you just replaced the pump the connector that runs fron the sending unit to the actual pump itself inside the tank also goes bad on this setup too,look for brown or burn marks on the inside of the sending unit where this connector hooks uo,hope this helps

Sep 11, 2009 | 2000 Chevrolet Blazer

1 Answer

Do you have to drop the tank to change the fuel pump on 93 plymouth voyager or is there a way from the top?


Yes the tank must be removed

Fuel Pump: Service and Repair
WARNING: The fuel system is under constant pressure, even when the engine is OFF. Always release fuel pressure before servicing any fuel
system component.
FUEL PUMP REMOVAL
1. Release fuel system pressure.
2. Fuel tank must be removed prior to fuel pump service.
3. Using a hammer and a brass drift, carefully tap the fuel pump lock-ring counter-clockwise to release the fuel pump.
4. Remove the fuel pump and its O-ring from the fuel tank, and discard the old O-ring.
5. Cover tank openings to prevent dirt from entering system.
FUEL GAUGE SENDING UNIT REMOVAL
1. Gently bend the sending unit locking tabs away from the sending unit.
2. Remove the electrical connector cover (red). Remove the sending unit wires from the electrical connector.
3. Use one screwdriver to push on the fuel pump body, and use another to release the sending unit locking tab from the sending unit.
4. Slide the sending unit assembly off of the fuel pump reservoir housing.
5. Pull the wires through the reservoir body and fuel pump cover plate.
FUEL GAUGE SENDING UNIT INSTALLATION
1. Bend the sending unit wires and lay them into the slot on the back of the sending unit.
2. Slide the sending unit into the slots on the fuel pump reservoir body. Slide the wires through the triangle shaped hole in the fuel pump reservoir
body. Check that the tab in the fuel sending unit locks into the detent in the fuel pump reservoir body.
3. Slip the wires onto the tab of the fuel pump reservoir body.
4. Slide the sending unit wire terminals into the electrical connector. Install the terminal locking cover.
5. Slide the fuel sending unit electrical connector into the bottom of the fuel pump electrical connector. Check that the connectors are securely
attached and fully pushed into each other.
FUEL PUMP INSTALLATION
1. Wipe seal area of tank clean, and install a new O-ring seal on pump.
2. Position fuel pump module in tank and secure with the lock-ring.
3. Using a hammer and a brass drift, carefully tap the fuel pump lock-ring clockwise to lock the module in place.
NOTE: Do not overtighten the lock-ring, because the fuel pump seal could split and leak.
4. Install fuel tank assembly.
NOTE: ASD and fuel pump relays remain energized for 7 minutes during the following test, unless the test is stopped or the ignition switch is
turned to the OFF position.
5. Using scan tool, place ignition switch in "RUN" position and use Actuate Output Test "Auto Shutdown (ASD) Relay", to activate fuel pump and
pressurize system.
6. Check for leaks.

Sep 10, 2009 | 1993 Plymouth Voyager

3 Answers

FUEL PUMP REPAIR


It will almost certainly be inside the gas tank. Pick up a Haynes manual, you'll be glad you did as this is not a simple job. You'll have to drain the fuel tank at least most of the way, lower it, remove the pump sending unit from the top of the tank, replace it and put it all back together.

Jun 19, 2009 | 1999 GMC Yukon

Not finding what you are looking for?
2004 Hyundai Santa Fe Logo

561 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8589 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...