Question about 2004 Isuzu Rodeo

1 Answer

2004 rodeo - attempting to remove stubborn rear brake drum- turned brake star adjustment the wrong way - wheel locked and cannot release it

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Isuzu Master
  • 450 Answers

Should be a hole in the backing plate to do adjustment from just under wheel cylinder may have rubber bung in hole look closely. can do with stumpy flat bladed screwdriver, may need probe or tiny flat screwdriver to hold auto adjuster lock up off of star adjuster

Posted on Aug 05, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I get the rear spindle off so I can replace the emergency brake shoes on my 2006 chrysler pacifica?



Adjustment

  1. Place parking brake lever in -full released- position.
  2. Raise and support vehicle.
  3. Remove plug in parking brake shoe support to access adjuster star-wheel.
  4. Through the access hole, rotate the adjuster star wheel in the following direction to expand the shoes outward against the drum:
    1. Left brake - Rotate star-wheel toward rear of vehicle.
    2. Right brake - Rotate star-wheel toward front of vehicle.
  5. Using an appropriate tool, turn adjuster star wheel until wheel will not rotate (dead lock).
  6. Back off adjuster six detents (teeth).
  7. Rotate wheel, checking for light drag. If drag is too heavy, continue to back off adjuster one detent at a time until light drag is present. Do not back off star-wheel more than 17 detents from wheel lock.
  8. Install access plug.
  9. Adjust opposite wheel parking brake shoes using same method.
  10. Lower vehicle.
  11. Apply and release parking brake lever once to ensure proper operation of parking brakes.


Removal & Installation NOTE The following procedure may be used to remove shoes on either side of the vehicle.

  1. Lock out automatic adjuster in parking brake lever.
  2. Raise and support vehicle.
  3. Access and remove rear hub and bearing.
  4. Remove parking brake cable bolt at knuckle.
  5. Completely back off parking brake shoe adjustment.
  6. Remove parking brake shoe adjuster spring.
  7. Remove shoe adjuster.
  8. Remove upper brake shoe hold-down clip and pin.
  9. Remove lower brake shoe hold-down clip and pin.
  10. Remove upper and lower shoes with return spring from shoe actuator.
  11. Remove return spring from shoes.

    0996b43f80204c12.jpg

    Fig. View of the actuator (1), support (2), adjuster spring (3), return spring (4), caliper adapter (5), shoes (6), hold-down clips and pins (7) and adjuster (8)

To install:
  1. Install return spring between upper and lower shoes.
    NOTE Before installing shoes on actuator, make sure actuator hooked to rear cable is positioned with word -UP- facing outward.
  2. Install upper and lower shoes with return spring on shoe actuator located on parking brake cable.
  3. Install lower brake shoe hold-down pin through rear of support and lower shoe, then install hold-down clip.
  4. Install upper brake shoe hold-down pin through rear of support and upper shoe, then install hold-down clip.
  5. Install shoe adjuster. Place end of adjuster with star wheel upward.
  6. Install parking brake shoe adjuster spring.
  7. Install bolt securing parking brake cable to knuckle and tighten bolt to 21 ft. lbs. (28 Nm).
  8. Using Brake Shoe Gauge, Special Tool C-3919, or equivalent, measure inside diameter of parking brake drum portion of rotor.
  9. Place Gauge over parking brake shoes at widest point.
  10. Using adjuster star wheel, adjust parking brake shoes until linings on both park brake shoes just touch jaws on gauge. This will give a good preliminary adjustment of parking brake shoes, before a final adjustment is made at end of this procedure.
  11. Install hub and bearing with wheel speed sensor as well as all components necessary to access it.
  12. Lower vehicle.
  13. Unlock automatic adjuster in parking brake lever.
  14. Perform final adjustment of parking brake shoes

  15. Adjustment This vehicle is equipped with permanently sealed rear wheel bearings. There is no periodic lubrication or maintenance recommended for these units.


    Removal & Installation

    1. Raise and support vehicle.
    2. Remove wheel mounting nuts, then tire and wheel assembly.
    3. If equipped with AWD:
      1. Remove cotter pin, nut lock and spring washer from half shaft.
      2. While a helper applies brakes to keep hub from turning, remove hub nut and washer.
    4. Remove brake caliper and rotor from hub and bearing assembly.

      0996b43f807cb548.jpg

      Fig. Hub assembly

    5. Disconnect vehicle wiring harness connector at wheel speed sensor connector.
    6. Unclip wheel speed sensor connector from spare tire mounting support.
    7. Disconnect two sensor cable routing clips on rear suspension crossmember.
    8. Disconnect two sensor cable routing clips along toe link.
    9. Disconnect sensor cable from bracket on brake support.

      0996b43f807cb54d.jpg
    10. Completely loosen, but do not remove four bolts fastening hub and bearing in place. Once loosened from threads in hub and bearing, push bolts up against rear of hub and bearing to keep brake support plate in place when hub and bearing is removed.

      0996b43f807cb54e.jpg

      Fig. Rear hub and bearing mounting bolts

    11. Pull hub and bearing off knuckle and half shaft (if equipped with AWD), then thread wheel speed sensor cable through hole in brake support plate as it is removed with hub and bearing.
      0996b43f807cb54f.jpg
    To install:
    1. Position hub and bearing bolts though rear of knuckle and parking brake support just enough to hold support in place as hub and bearing is installed.
    2. Install hub and bearing by first feeding end of wheel speed sensor cable through hole in bottom of parking brake support. As this is being done, if equipped with AWD, slide hub and bearing onto half shaft. Place hub and bearing through brake support, onto knuckle, lining up mounting bolt holes with bolts and placing wheel speed sensor head at bottom.
    3. Install four bolts fastening hub and bearing in place. Tighten mounting bolts to 60 ft. lbs. (81 Nm).
    4. Place wheel speed sensor cable routing grommet into bracket on parking brake support.
    5. Route wheel speed sensor cable along toe link and rear suspension crossmember connecting routing clips where shown.
    1. Connect vehicle wiring harness to wheel speed sensor connector.
    2. Install brake rotor and caliper.
    3. If equipped with AWD:
      1. Install washer and hub nut on end of half shaft.
      2. While a helper applies brakes to keep hub from turning, tighten hub nut to 180 ft. lbs. (244 Nm).
      3. Install spring washer, nut lock and cotter pin on end of half shaft.
    4. Install tire and wheel assembly. Install and tighten wheel mounting nuts to 100 ft. lbs. (135 Nm).




May 18, 2011 | 2006 Chrysler Pacifica

2 Answers

How do you get the drum off a 1999 dodge caravan


Take a look here:



c17hydro_171.gif
Many times it is necessary to retract the shoes slightly by turning the adjuster
star (inside the brake drum) to remove the drum.

If the drum is difficult to remove, remove the plug from the rear brake support plate. Push the self adjuster lever away from the star wheel using a thin screwdriver. The lever and star wheel are accessed through the hole on the rear brake support plate. Rotate the star wheel using a brake adjusting tool to retract the shoes.

May 08, 2011 | 1999 Dodge Caravan

1 Answer

My 2004 Isuzu Rodeo was recently inspected and failed because the two rear brakes are not applying at the same time. I was told the rear right brake is applying about half as fast as the left. How do I fix...


The easiest way is to pull the wheels and the drum and adjust the self adjuster
at the bottom (it is a threaded affair with a sprocket on it at the bottom of the
assembly). They sell a tool to adjust this without pulling wheels,
but I always found it easier to do it with the wheels removed
which allows inspection of the self adjuster and springs and brake "nails".
Adjust the pads until they just touch the drums and then back them off a little.
push the brake pads together before reinstalling the drum, spin the drums to make sure
they aren't scrubbing, reinstall wheels and take for a test drive to make sure the
pads are seated and recheck if necessary. It sounds complicated but the hardest part
is taking off the wheels and drums. Hope this is useful.

Mar 24, 2011 | 2004 Isuzu Rodeo

2 Answers

How to take of brake drum off on 1997 oldsmobile achieva


After the wheel and tire are removed, rare back with a big hammer and hit the brake drum on the corner, putting blaster ( Pentrating oil ) around the hub center and the studs, will help too. You may need to hit it very hard and many times. once moving and it still won't come off or it won't even turn, your going to have to release the brake, The parking brake must be off and it's possible that now you have it jacked up you wisely put the brake on, but it has to be off to remove the drum, ( choulk the wheels that are on the ground before releasing the brake) Some drums have 8MM threaded bolt holes in them that let you thread a bolt into the hole and as you tighten it the drum is pulled off, Not all drums have these holes made in them.

Sep 18, 2010 | 1998 Oldsmobile Achieva

1 Answer

2006 Pacifica emergency brake problem.


The only manual adjustment for the parking brake on these is at the shoes themselves. Procedure for that is as follows:

1) Place parking brake lever in "full released" position.
2) Raise and support vehicle.
3) Remove plug in parking brake shoe support to access adjuster star-wheel.
NOTE: Through the access hole, rotate the adjuster wheel in the following direction to expand the shoes outward against the drum.
Left brake--Rotate star wheel toward rear of vehicle.
Right brake--Rotate star wheel toward front of vehicle.
4)Using an appropriate tool, turn adjuster star wheel until wheel will not rotate (dead lock).
5) Back off adjuster six detents (teeth).
6) Rotate wheel, checking for light drag. If drag is too heavy, continue to back of adjuster one detent at a time until light drag is present. Do not back off star-wheel more than 17 detents from wheel lock.
7) Install access plug.
8) Adjust opposite wheel parking brake shoes using same method.
9) Lower Vehicle.
10) Apply and release parking brake lever once to ensure proper operation of parking brakes.

These directions are directly from 2006 Pacifica factory service manual. If you have any other problems feel free to ask. v\:* {behavior:url(#default#VML);} o\:* {behavior:url(#default#VML);} w\:* {behavior:url(#default#VML);} .shape {behavior:url(#default#VML);} Normal 0 false false false /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-parent:""; mso-padding-alt:0in 5.4pt 0in 5.4pt; mso-para-margin:0in; mso-para-margin-bottom:.0001pt; mso-pagination:widow-orphan; font-size:10.0pt; font-family:"Times New Roman"; mso-ansi-language:#0400; mso-fareast-language:#0400; mso-bidi-language:#0400;}
v\:* {behavior:url(#default#VML);} o\:* {behavior:url(#default#VML);} w\:* {behavior:url(#default#VML);} .shape {behavior:url(#default#VML);} Normal 0 false false false /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-parent:""; mso-padding-alt:0in 5.4pt 0in 5.4pt; mso-para-margin:0in; mso-para-margin-bottom:.0001pt; mso-pagination:widow-orphan; font-size:10.0pt; font-family:"Times New Roman"; mso-ansi-language:#0400; mso-fareast-language:#0400; mso-bidi-language:#0400;}

Mar 07, 2010 | 2006 Chrysler Pacifica

1 Answer

Is there a trick to removing rear brake drums on a 2004 corolla besides releasing the parking brake and loosening the adjuster star wheel?


The only trick is banging it off. Drums are known to be "frozen" on or stuck. Honestly, the only way to get them off when they are stuck is to carefully hammer it off. Below is what is required to remove and replace the drum....and a picture of your system:

Removal & Installation
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Remove the wheels.
  3. Remove the brake drum from the axle hub.
To install:
  1. Install the brake drum.
  2. Install the rear wheels, tighten the wheel lug nuts.
b936120.gif

Oct 29, 2009 | 2004 Toyota Corolla

2 Answers

How do you rmove rear brake drum 2004 frontier 4x4


Hope this helps.
Good luck,

Removal & Installation


  1. Remove the hub cap and loosen the lug nuts.
  2. Raise the rear of the vehicle and support it on jackstands.
  3. Remove the lug nuts, tire and wheel.
  4. Release the parking brake.
  5. Pull the brake drum from the hub. If difficult to remove try the following:
    1. Strike the face of the drum with a plastic or rubber mallet. This will break free any rust that may develop between the drum and the hub.
    2. Install 2, M8x1.25mm bolts into the holes in the drum and gradually tighten them to pull the drum off the hub.



  6. 0900c152801a5f72.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Install and tighten 2 bolts to remove a stubborn brake drum

To install:
  1. Install the brake drum to the hub.
  2. Install the wheel.
  3. Remove the jackstands and lower the vehicle.
  4. Road-test the vehicle to ensure that the brakes are working properly.

  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Drain the brake fluid, as necessary.
  3. Release the parking brake.
  4. Raise the vehicle and support safely.
  5. Remove the tire and wheel assembly.
  6. Pull the brake drum from the hub. If difficult to remove try the following:
    1. Strike the face of the drum with a plastic or rubber mallet. This will break free any rust that may develop between the drum and the hub.
    2. Install 2, M8x1.25mm bolts into the holes in the drum and gradually tighten them to pull the drum off the hub.

      0900c152801a5f72.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Install and tighten 2 bolts to remove a stubborn brake drum

Oct 23, 2009 | 2004 Nissan Frontier

1 Answer

Trying to remove rear brake drum cover,have already adjusted star wheel and still won't remove. what am i doing wrong? for a 93 plymouth grand voyager


  1. Raise and support the rear of the vehicle on jackstands.
  2. Remove the wheels and tire assemblies.
  3. Remove the brake shoe adjusting slot cover from the rear of backing plate.
  4. Insert a thin tool through the adjusting slot and hold the adjusting lever away from the star wheel.
  5. Insert an adjusting tool and back off the star wheel by prying downward with the tool.
  6. Remove the center hub dust cover, nut, washer, brake drum, hub and wheel bearings.
To install:
  1. Inspect the brake lining and drum for wear.
  2. Inspect the wheel cylinder for leakage. Service as required.
  3. Remove, clean, inspect and repack the wheel bearings.
  4. Install the brake drum and tighten the hub nut to 20-25 ft. lbs. (27-34 Nm), then back off the nut until bearing pressure is released.
  5. Retighten the nut finger tight, align the cotter pin hole and install the cotter pin.
  6. Adjust the rear brakes as described in the beginning of this section.

36e0d00.gif
Removing the rear drum adjusting hole cover plug

Oct 07, 2009 | 1993 Plymouth Grand Voyager

3 Answers

CANT GET REAR DRUM BREAKS TO DECOMPRESS


If you look on the side of the drum there is a rubber plug . Remove the plug and use a screwdriver to release the tension by turning the jacking screw.

Jul 26, 2009 | Chevrolet Silverado 1500 Cars & Trucks

4 Answers

03 SILVERADO DRUM BRAKES


TO REMOVE BRAKE DRUM.IF ITS HAS PRESSED METAL WASHERS.CUT THEM OFF.TO GET A STUCK BRAKE DRUM. OFF. REMOVE THE PLUG FROM BACKING PLATE.AND PUSH THE PARKING BRAKE LEVER OFF ITS STOPS.WITH A SCREW DRIVER AND BRAKE ADJUSTING TOOL.TURNING ADJUSTER STAR WHEEL UPWARD.TO RETRACT THE SHOES.THEN REMOVE DRUM.

Jul 26, 2009 | 1999 Chevrolet 3500

Not finding what you are looking for?
2004 Isuzu Rodeo Logo

354 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14384 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...