Question about 2007 Nissan Frontier SE Crew Cab

Open Question

Check engine code P0420 for a 2007 Nissan Frontier

What part has to be replaced

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 10 Answers

SOURCE: Nissan Frontier torsion bar replacement

well it depends how you want to adjust it, if you want to lower it, back out the screw on the torsion key a couple of turns. raise, screw it in a couple of turns

Posted on May 29, 2008

Ad
SUL827
  • 93 Answers

SOURCE: Nissan 2007 Frontier tire pressure monitoring system

You need to set all the pressures to 35 psi. first then drive for approx.1/4 mile. If this doesn't work to reset the light (keep in mind the code itself will still be stored even though the light goes off) you will need to take it to your Nissan Dealer to have it scanned as there may be a malfunction with the sensor. If faulty and you are under 36k miles then it should be covered under your factory warranty. Hope this helps.

Posted on Oct 17, 2008

pal03246
  • 726 Answers

SOURCE: Nissan Sentra 2001 gxe with code p0420

You will need a new catalytic convertor assembly. Yours is below treshold efficiency in other words its "no good".If you have it replaced, ask the garage/dealer to give you the old one back. Its worth some cash if its full. It doesn't matter thet it failed. They are going after the mesh inside of it and that is worth some $$$$. May not be much , but better than nothing.

Posted on Jul 26, 2009

  • 495 Answers

SOURCE: 2003 nissan murano with check engine light codes

P0420 is Catalyst System Efficiency Below Threshold - Bank 1
and
P0456 is EVAP Control System Very Small Leak (Negative Pressure Check)

Posted on Nov 22, 2009

lindsay836
  • 677 Answers

SOURCE: engine code p0340. replaced distributor

The engine code you have given is a p0340, which is a cam sensor.
Why did you replace the distributor ?
Please let me know.

Posted on Feb 06, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

While coming to a stop, my 2004 Nissan frontier died. Checked fuel pump, it did come on, checked to see if getting fire. Could not get fire from any plug wires. Checked codes came up with P0340 &...


Sorry to the bearer of bad news but i have a funny feeling your ECU unit has failed ,where is it located on this vehicle anywhere near the engine where it can get hot?

Nov 29, 2013 | 2004 Nissan Frontier XE

1 Answer

Check engine light 2003 frontier nissan


I suggest scanned the computer car in order to know what fault code is stored there; note his code number and send us for other details.


Keep in touch.

Dec 31, 2012 | 2004 Nissan Frontier

1 Answer

I just replaced my evap vent valve n reset the code and my check engine light came bak on do i have to drive it so many miles to reset itself or wut should i do


If you cleared the codes and it light came right back on than you did not make the proper repair. What code or codes do you have?

Feb 05, 2012 | 1998 Nissan Frontier

1 Answer

I recently replaced the passenger side head gasket on my 3.3L 2000 Nissan Frontier. The Check Engine light was on so we scanned it, and it was throwing 3 codes, the first one was a Code 34, the knock...


in your air box you will see a wire with a sensor on top,,replace this sensor and engine check light will be gone the next time you start the jeep ,job done

Jun 19, 2010 | 2000 Nissan Frontier

1 Answer

2005 Frontier: Service engine stays on, 2005 Frontier 6 Cyl.have ...


Go to a different dealer. The dealer should know what is wrong with the vehicle by the codes. Don't let them keep guessing what is wrong and having you replace random parts.

Nov 01, 2017 | 2005 Nissan Frontier

1 Answer

Engine code p0340. replaced distributor 2001 nissan frontier


The engine code you have given is a p0340, which is a cam sensor.
Why did you replace the distributor ?
Please let me know.

Feb 06, 2010 | 2001 Nissan Frontier Crew Cab

1 Answer

Nissan frontier 98


Visit http://www.troublecodes.net/Nissan/95ams96-00.shtml#frontierx24

for code listing for your car.

Rate this.

Aug 09, 2009 | 1998 Nissan Frontier

1 Answer

2000 Nissan Frontier quit running


You have not run a engine control module fault code test, this is key to finding the possible causes. Borrow or buy a OBD2 code reader and check the codes

Sep 11, 2017 | 2000 Nissan Frontier

Not finding what you are looking for?
2007 Nissan Frontier SE Crew Cab Logo

Related Topics:

420 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

79865 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...