Question about 1992 Mercury Grand Marquis

1 Answer

Where is windshield wiper motor for 1992 mercury grand marquis

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Mercury Master
  • 17,970 Answers

1992-98 Vehicles

  1. Disconnect the negative battery cable.
  2. Remove the rear hood seal. Remove the wiper arm assemblies by raising the wiper blade off the windshield. Move the slide latch away from the pivot shaft and slowly lower the arm onto the latch. This unlocks the arm from the pivot shaft and holds the blade off the glass. Pull the arm from the pivot shaft.
  3. Remove the cowl vent screws and disconnect the washer hoses from the washer jets.
  4. Detach the electrical connectors from the wiper motor.
  5. Remove the wiper assembly attaching screws, lift the assembly out and disconnect the washer hose.
  6. Unsnap and remove the linkage cover.
  7. Remove the wiper module assembly retaining bolts and remove the module from the vehicle.
  8. Remove the linkage retaining clip from the motor operating arm by lifting the locking tab and pulling the clip away from the pin.
  9. Remove the motor retaining screws and remove the motor from the vehicle.
  10. The installation is the reverse of the removal.

where is windshield wiper motor for 1992 mercury - ad37f8d.jpg

Fig.: Lift up to release the clips and remove the hood-to-cowl weather strip


ca6ea0f.jpg

Fig.: Remove the cowl panel-to-firewall retaining clips



Remove the driver's side then the passenger side cowl panel from thwhere is windshield wiper motor for 1992 mercury - d57f264.jpgspan>


d57f264.jpg



Fig.: Detach the electrical connector for the wiper motor

Release thewhere is windshield wiper motor for 1992 mercury - ffed3a6.jpgr retaining clips and remove the cover from the vehicle


ffed3a6.jpg



remove the module from the vehicle


412221d.jpg



Fig.: Remove the wiper motor retaining bolts and ...


46edc09.jpg


Fig.: ...remove the wiper motor from the vehicle




Hope helps (remember comment and rated this).

Posted on Aug 02, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to remove windshield wiper motor off of 1999 mercury marqui


Wiper motors on this car are a very rare failure, so have you jumped 12 volts to the wiper motor and does it work or not, do that before you tear into it. The switch is the more common issue. Also the wiper motor can be tested with a Ford special scan tool called and "NGS", it runs the wiper motor through it's cycles by controlling the BCM..

Mar 24, 2017 | 1999 Mercury Grand Marquis

1 Answer

2003 grand marquis turn on the wipers and the instrument lights go out.


Could be a grounding issue , instrument cluster and the windshield wiper motor an switch share ground 201 . lose connection possibly . Pull the driver side left kick panel and look for wires screwed or bolted fast to the car body

Dec 12, 2016 | 2003 Mercury Grand Marquis

1 Answer

Wiper motor removal and replacement


Remove wiper arms, remove lower windshield plastic cover, remove wiper washer connector, remove 8 8mm wiper housing, disconnect wiper motor remove from car...remove 3 10mm bolts and center 8 mm bolt and remove motor. ..reverse and reinstall

Feb 26, 2014 | 2003 Mercury Grand Marquis

1 Answer

1996 Mercury Grand Marquis wipers don't work. I changed the motor and the fuse isn't blown


You need to take the plastic cowls off that cover the wiper arm linkage and wiper transmission to inspect it...cowl is held on with 3 Phillips screws near windshield and some one inch wide metal clips, take off the gasket that fits on top. If both are not working check the transmission where linkages attach, if one wiper blade is not working it is usually the drivers side where the nylon bushing that forns a ball/socket sort of connection fails due to build up of debris and the rusting of parts that follows, let me know if this helps.

Dec 17, 2012 | 1993 Mercury Grand Marquis

1 Answer

2001 grand marquis windshield wipers runs in high nothin else wont go in park either


If you are having problems with the wipers not wanting to park, that is usually the park switch inside the wiper motor. The low and interm speed settings could be the delay module which could also affect park.
You may need a shop manual to troubleshoot the circuits.

Dec 15, 2012 | 2001 Mercury Grand Marquis

1 Answer

When i turn my windshield wipers off they go to the up position i have a 1996 grand marquis ls


You have a bad park in your wiper motor, just replace the wiper motor and it will fix your problem. I work for Yellow Cab of Kansas City and we have 240 crown vic's on our fleet. They are the same car pretty much and we have this problem all the time. Good Luck to ya!

Apr 08, 2011 | 1993 Mercury Grand Marquis

1 Answer

1996 Mercury Grand Marquis - wipers will not work. Have check multifunctional switch and motor. Both ok.


if motor and switch are ok and the motor is running, then it's the ball joints on the arms that have become disconnected underneath the windshield in the firewall vicinity. Also, the wiper arms could be stripped out.

Jul 03, 2010 | 1996 Mercury Grand Marquis

1 Answer

How do you remove windshield wipers on a 1997 mercury grand marquis?


If your'e just removing the wiper blade, check for a "release lever" where the wiper attaches to the arm, push (or pull) the lever and pull down on the blade at the same time. Do the opposite to install, except you do not have to push the release lever.
If you are removing the whole arm, there is a special tool that you slide under the arm that releases it from the 'gear'.

Nov 07, 2009 | 1992 Mercury Grand Marquis

1 Answer

Wipers finish in the up position when turned off. Windshield wipers do not go down when turned off.


SOUND LIKE WIPER LIMIT SWITCH IN MOTOR IS BAD.YOU HAVE TO REPLACE THE WIPER MOTOR UNIT.BECAUSE LIMIT SWITCH IS MADE IN UNIT.

Aug 24, 2009 | 1996 Mercury Grand Marquis

Not finding what you are looking for?
1992 Mercury Grand Marquis Logo

1,076 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

fordexpert

Level 3 Expert

5546 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...