Question about 1989 Chevrolet C1500

Open Question

Blinking Parking brake light

The parking brake light is blinking seven times then pauses in the on state and repeats.
What does this code indicate?

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
fastboyz
  • 674 Answers

SOURCE: I have a 1989 s-10.The

RWAL Fault codes
Codes for Dodge RWAL, Ford RABS and GM RWAL applications are similar but have a few differences:

  1. Should not occur (replace the controller if it does)
  2. Open isolation valve circuit or defective ABS module
  3. Open dump valve circuit or defective ABS module
  4. Grounded or closed RABS or RWAL valve switch
  5. Excessive actuations of dump valve during ABS braking
  6. Erratic speed sensor signal
  7. Shorted isolation valve or defective ABS module
  8. Shorter dump valve or defective ABS module
  9. High resistance or open speed sensor circuit (resistance should be 1000 to 2500 ohms)
  10. Low speed sensor resistance (Dodge & Ford only)
  11. Open speed sensor circuit (GM only)
  12. Stop lamp switch circuit (Dodge & Ford)
  13. ABS module speed processor (Dodge & Ford only)
  14. ABS module program (Dodge & Ford only)
  15. ABS module RAM memory failure (Dodge & Ford)
To manually clear a stored fault code on GM and some Dodge trucks with RWAL, remove the ABS fuse or disconnect the battery for 5 seconds. Ford RABS codes will automatically clear when the ignition is turned to the off position.

Posted on Aug 26, 2008

Ad
  • 8 Answers

SOURCE: how to adjust parking brake 05 impala.

u will nead to get under the car. how u go about that is up to u but do it safe an have mate around. go to your front door this is the best place easy to reach your hand brack hear. look where the gear stick is up front u nead to be under the car where the gear stick is find it then look a bit downback from gear stick an u will see it. when u do the hand brake up do not hav it on u wont to have max 8 click,s an u,ll be fine. hope this helps u

Posted on May 28, 2009

  • 4 Answers

SOURCE: parking brake pedal goes to floor

The disc brake pads are NOT used for the parking brake. The parking brake uses mini-drum type shoes inside the rear disc rotor.

Take a look at http://wiki.answers.com/Q/How_do_you_change_the_emergency_brake_pads_on_a_2000_Chevy_1500_Silverado_Pickup

For more info

Posted on Jun 21, 2009

  • 1129 Answers

SOURCE: 2005 parking brake stuck

The parking brake cable should be replaced but in the short term try getting under the truck and grabbing the cable casing and move them around to get the seized cable inside the cable casing to release keep working the cable until it releases if this doesn't work replace both cables.

Posted on Sep 11, 2009

  • 1 Answer

SOURCE: parking brake cable snapped but brake is on. any

I just had my parking brake cable snap on me also. I'm with Denie 1300, it's right under the dash and has a "U" shape lever facing down. Tug on that and the parking brake will release. As a matter of fact, It's a very simple fix, just need to purchase the cable and replace it. If you take it to a dealership, they'll want to charge you a whole bunch, and it's really an easy fix.

Posted on May 24, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you fix code p1589 in Toyota Vitz?


P1589- Acceleration sensor learning.
Zero Point Calibration Using Jumper wire

The following manual procedure may be used in the cases where a Diagnostic Tester is
not available.

CAUTION:
While performing the Zero Point Calibration, do NOT tilt, move, or shake the vehicle.
The vehicle must remain in a stationary condition throughout the entire process.
Be sure to perform the procedure on a level surface with an inclination of less than 1%.

1. If the vehicle is equipped with A/T, ensure that the shift lever is in the "P" range and
the parking brake is applied. If the vehicle is equipped with a M/T, ensure that the
parking brake is applied.
2. Turn the ignition switch ON.
3. Using the SST, repeat a cycle of short and open between terminals Ts and CG of
DLC3 4 times or more within 8 seconds (refer to the specific vehicle EWD for TS and
CG pin location in the DLC3).
4. Verify that the VSC indicator light is lit indicating the recorded zero point is erased.
5. Turn the ignition switch OFF.
6. Be sure the terminals Ts and CG of DLC3 are disconnected.
7. Turn the ignition switch ON.
8. Check that the VSC warning light goes off about 15 seconds after the ignition switch
is turned ON.
9. After ensuring that the VSC warning light remains OFF for 2 seconds, turn the ignition
switch OFF.
10. Connect terminals Ts and CG of DLC3 using the SST.
11. Turn the ignition switch ON.
12. After turning the ignition switch ON, check that the VSC warning light is lit for about
4 seconds and then starts quick blinking at 0.13 second intervals.
13. After ensuring the blinking of the VSC warning light for 2 seconds, turn the ignition
switch OFF.
14. Remove the SST from terminals Ts and CG of DLC3.
15. Drive the vehicle for at least 5 minutes to confirm Zero Point Calibration is complete.
IF FAILED REPLACE THE BRAKE ACTUATOR - SKID CONTROL ECU.

Jan 18, 2016 | Toyota Cars & Trucks

Tip

How To Check & Reset Your 2002-2006 Nissan Altima Service Engine Soon (SES)...


The following directions will help you decode your 2002-2006 Nissan Altima's Service Engine Soon (SES) light and reset it.<br /> <br /> <span style="font-weight: bold;">Obtain The Trouble Code</span><br /> <ol> <li>Turn the ignition key to the ON position and wait three seconds.</li> <li>Put the accelerator pedal to the floor and release it five times in less than five seconds.</li> <li>Wait exactly seven seconds. Put the accelerator pedal to the floor for ten seconds until the SES light flashes.</li> <li>Release the accelerator pedal and start counting flashes to obtain the four-digit trouble code.<br /></li></ol> <ul> <li>Long flashes (0.6 seconds) indicate the first digit of the code; count the blinks one through nine and write down the first digit. (Ten blinks indicates a zero.) </li> <li> The next three digits blink faster (0.3 second) and have a 1 second pause between digits.</li> <li>The ECM code repeats until you turn the ignition key to the OFF position.</li> <li>You can look up the trouble codes in the Service Manual.</li> <li>If you get four blinks of ten, or 0000, the ECM indicates no malfunction.<br /></li></ul> <br style="font-weight: bold;" /><span style="font-weight: bold;">Clear The Trouble Code</span><br /> <ol> <li> Clear the code and the SES light by holding the accelerator pedal down to the floor for 10 seconds or more while the SES light is blinking.</li> <li>When the pedal is released, the ECM will erase the trouble code(s).</li></ol>

on Feb 15, 2011 | 2002 Nissan Altima

1 Answer

A/C and Heater, Drivers side airbag light


For bower fan check:
- Speed controller assembly of blower fan.
- Wiring harness and fuse
- Blower fan.
To solve the air bag light problem retrieve the SRS error codes with the help of diagnostic computer and follow the description.
You can also check the error codes manually as described below.

cedd3ab6-1868-4077-a1e0-5a91b74080b0.jpg
Procedure:
Read the blinking patterns of the DTCs. As examples, the blinking patterns for the normal system code and DTCs 11 and 31 are shown in the following diagram. The first blinking pattern indicates the first digit DTC. The second blinking pattern occurs after a 1.5-second pause. If there are two or more DTCs, there is a 2.5- second pause between each DTC. After all DTCs are shown, there is a 4.0-second pause, and they are all repeated.
HINT:
• If 2 or more malfunctions are found, the indication begins with the lowest numbered DTC.

0f9ed446-61ad-4a79-a503-a38466c78cef.png

Feb 26, 2014 | 2006 Toyota Matrix

1 Answer

Why when my i turn my left turn signal on, both rear brake lights blink


If the brake lights are blinking and not the parking lights, chances are the problem is a short in the turn signal switch.
If the parking lights are blinking it could be a short in one of the lamp sockets.

Jan 16, 2013 | 1994 Chevrolet Caprice Classic

1 Answer

Parking brake wont deactivate


Did you check to see what codes you
may have?

Same procedure every time now, for the
last 30 years,on any vehicle

May 26, 2012 | 2006 Volkswagen Passat

1 Answer

I have a passat 2006 fsi. The Parking breaks wont release after pressing the release button


I had the same problem on my Passat Variant 2007.
Randomly Park Brake won't activate and/or deactivate once button PB pressed.
The cockpit computer tells "Park Brake Error" (or something similar).
If this is your problem, the issue is very well known to VW Service centers.
I had solved it by bringing the car to the Service: The told me that they substituted the ParkBrake Button (a differently made one, even if identical on the exterior) and Reprogramming (Updating) the car computer software.

May 26, 2012 | 2006 Volkswagen Passat

1 Answer

Parking brake light keeps blinking, 4 blink code?


make sure emergency brake pedal is pulled all the way up

May 06, 2009 | 1992 GMC Sonoma

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

76 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6910 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...