Question about 2004 Mercury Mountaineer

1 Answer

Repair front wheel bearing assembly

I have a 2004 Mercury Mountaineer with bad front wheel bearings. How do I replace the front wheel bearings/ assembly and are there any special tools or applications needed? Thank You ...Jay

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 149 Answers

No special tools in particular just the usual or necessary tools required.. 1stly u remove the Tyre and the caliper then u'll see something like a long rod dats the bearing

Posted on Aug 02, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Need replace the rear wheel studs on 2004 mercury mountaineer 4.0 6 cyl AWD


replace the whole hub assembly with new bearing and hub kit hub must be presed apart n presed back together yo

Dec 19, 2012 | 2004 Mercury Mountaineer

2 Answers

Car makes a "humming" noise


probably right side bearing if its front unless you have a 20 ton press lying around your gonna need to go to somewhere and pay dearly to have it replaced sorry for the bad news good luck please rate

Mar 07, 2011 | 2004 Mercury Mountaineer

1 Answer

2003 Merc Mountaineer AWD Grinding coming from left front tire. Tires, brakes, rotors all less than a year old, could it be a hub/bearing assembly or something different? Thanks in advance.


Hi and welcome to FixYa!
Looks like a wheel bearing issue. If the wheel bearing is worn out you can expect a grinding sound. Wheel bearing replacement is strongly recommended.

Hope this helps and thank you for using FixYa! Have a good one!

Feb 23, 2011 | 2003 Mercury Mountaineer

3 Answers

My 2003 mercury mountaineer ABS light is staying on. manually, the brakes work however they shimmy.changed the brake pads,checked the brake fluid and ABS fuse,bud when changing the pads,did now clean the...


I replaced the hub bearing assembly on drivers side twice and the light stayed on and the brakes worked fine. It was the wires (visible just above the tire on the frame) that rubbed against the frame that had shorted out. It was simply repaired and clip-stripped up out of the way. The light has been off every since then.

Dec 30, 2010 | 2003 Mercury Mountaineer

1 Answer

Drivers side wheel bearing what do i need to do to replace it myself


Front - Remove tire, then remove brake caliper and caliper braket, remove brake rotor, some times will have little clips, remove clips, if they break ok, won't used them again, if 4X4 remove center axle nut, disconnect ABS harness, on back side of bearing, there will be three bolt's that hold hub bearing assembly, remove bolts, bearing should slide out, some time with a little help from a hammer, and your done , reverse to install new hub bearing assembly, just make sure that ABS harness is in same location that old one was when putting bearing in.

Jul 21, 2010 | 2004 Mercury Mountaineer

2 Answers

Have a 1998 awd mercury mountaineer and the front wheel bearing is going bad. Do I need to replace the whole assembly or just the bearing? ty


nowadays, mechanics can change an assembly and pay only $55 to $75 or up for the whole hub assembly complete with the abs wheel speed sensor.

The assembly comes with a new bearing. Otherwise, special knowledge and tools are required to press a new bearing on to the old hub, which probably is rusty.

So, it makes sense to change the whole hub assembly when the bearing goes bad, and many times get a lifetime warranty on the part..

Good luck on this one.

Jul 04, 2010 | Mercury Mountaineer Cars & Trucks

1 Answer

1998 Mercury Mountaineer wheel bearing What tools are needed to change the front wheel bearing on a four wheel drive.


2x2 = nothing special since they are old fashion tapered bearings

4x4 = nothing special again BUT the wheel bearing is part of the hub assembly!

Jul 17, 2009 | 1998 Mercury Mountaineer

Not finding what you are looking for?
2004 Mercury Mountaineer Logo

1,177 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

fordexpert

Level 3 Expert

5546 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...