Question about 1997 GMC Jimmy

1 Answer

The windshield wiper does not run, but i can hear a humming when i turn it on. I was told that it may need some kind of module.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 488 Answers

It sounds like you may have a broken drive from the electric motor or the linkage to the wiper arms have broken.. The only way to tell for sure is to strip out the wiper motor and the linkages..which can be a big job and can entail removal of several other parts first.. Try moving the wiper arms manually, with your hands.. If you can move the wiper arms across the screen then the linkages have broken and will need to be replaced as they are not a repairable item..

Posted on Aug 02, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

My windshield wipers wont work.


It Sounds Like, Either The Arms Are Loose ,If You Can Hear Something Moving Behind The Dash,
Or The Linkages Are Seized ,If The Motor Just Hums No Movement Heard,In Which Case Try Spraying Q 20 On The Linkage And Try Moving The Wiper Arms By Hand To Get It Going Again,
If Not The Motor May Just Be Burn;t Out.

Mar 16, 2013 | Cars & Trucks

1 Answer

I've got a 98 Jetta GL, and recently I turned on the windshield wipers by accident when there was snow on it, and they wouldn't move. When I try to turn them on, I hear a humming noise, so the motor must...


I've got the exact same problem. Sears said there are screws loose. I told them not to do anything and that I would look at them myself. Haven't done it yet, but I am going to give it a try.

Dec 14, 2010 | Volkswagen Jetta Cars & Trucks

2 Answers

Windshield washer will not squirt


Make sure you have water or windshield wiper fluid in the reserve (open your hood and add more, look for a blue plastic cap) if you hear it humming when you turn it on then the pump is working. Also check the little nozzles on the hood (one on each side) and see if they are clogged, stick a small safety pin into the holes and move it in and out to free up ant debris inside that may stop the water from squirting out

Nov 19, 2009 | 2008 Chevrolet Equinox

1 Answer

How do I remove the windshield wiper motor from a Ford F-250?


2002 Ford F-250 Windshield Wiper Motor Removal & Installation 1. Turn the ignition switch to the ON position. Turn the ignition switch ON until the wiper blades are straight up, then turn the ignition switch OFF. 2. Disconnect the negative battery cable. 3. Remove the right-hand and left-hand windshield wiper arm and blade assemblies. 4. Remove the cowl top vent panels. 5. Detach the electrical hardness connector at the windshield wiper motor assembly. 6. Remove 3 wiper motor (module assembly) retaining bolts and remove the module assembly from the vehicle. 7. Remove the wiper linkage retaining bolt and remove the linkage from the wiper motor. 8. Remove 3 retaining nuts and remove the windshield wiper motor To install; 9. Place the windshield wiper motor in position and install 3 retaining nuts. Tighten to 10-12 ft. lbs. (12-17 Nm). 10. Connect the wiper linkage to the windshield wiper motor and install the retaining bolt. Tighten the bolts to 14 ft. lbs. (20 Nm). 11. Place the wiper motor (module assembly) in position and install 3 retaining bolts. Tighten the bolts to 6 ft. lbs. (9Nm). 12. Install the electrical hardness connector to the windshield wiper motor. 13. Connect the negative battery cable. 14. Allow the windshield wiper motor to cycle several times while checking for proper wiper motor operation. 15. Turn the windshield wiper motor to the OFF position to park the wiper motor in the park position. 16. Install the cowl top vent panels. 17. Install the wiper arm and blade assemblies. Install the retaining nuts and tighten to 22-29 ft. lbs. (30-40 Nm). 18. Connect the negative battery cable. 19. Check the windshield wiper motor for proper operation and the wiper arms for adjustment.

Nov 09, 2009 | 2002 Ford E250

1 Answer

Ford Taurus 1999SE-Windshield wiper motor just hums.How to fix ?


Removal & Installation To Remove:
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Disconnect the battery ground cable.
  3. Remove the wiper arms.
  4. Remove the 8 plastic retainers and the 6 clips holding the cowl vent screens to the inner panels. Turn the retainers 1⁄4 turn counterclockwise to remove.
  5. Remove the cowl vent screens.
  6. Disconnect the electrical connector from the wiper motor and remove the 4 bolts that mount the module assembly to the cowl.
  7. Remove the windshield wiper module from the vehicle.
  8. Rotate the wiper operating arm in a clockwise direction to gain access to the bolt retaining the arm to the motor. WARNING
    Always rotate the wiper operating arm in a clockwise motion or damage to the motor could occur.
  9. Remove the nut retaining the wiper operating arm to the wiper motor.
  10. Remove the three wiper motor-to-wiper module assembly retaining bolts and remove the motor from the vehicle.
To Install:
  1. Position the wiper motor on to the module assembly. Install the three wiper motor-to-wiper module assembly retaining bolts. Tighten the bolts to 115-151 in lbs (13-17 Nm).
  2. Position the wiper operating arm on the wiper motor output shaft. Install the mounting nut and tighten to 22-29 ft-lbs (30-40 Nm).
  3. Position the windshield wiper module onto the cowl. Install the mounting bolts and tighten to 106 in-lbs (12 Nm).
  4. Connect the wiper motor electrical connector.
  5. Position the cowl vent screens onto the inner panels. Install the 8 plastic retainers and the 6 clips holding the cowl vent screens to the inner panels. Turn the retainers 1⁄4 turn counterclockwise to install.
  6. Install the wiper arms.
  7. Connect the battery ground cable.
  8. Adjust wiper arms if necessary.

Here is the picture of the motor....it is the round object in the middle of the picture that looks like a can and has a square block on the end of it.

You have to remove the cowl vent panel....just under the windshield. $64.00 for a new motor.

Oct 01, 2009 | Ford Taurus Cars & Trucks

1 Answer

Need to get a programmer dont know where its at


  • Windshield Wipers Continue to Run When Turn Signal and Windshield Wiper Switch Are Turned OFF
  • Damaged turn signal and windshield wiper switch .
  • Damaged windshield wiper motor .
  • Damaged windshield wiper control module.
7fd52e7.gif
efd7dbe.gif
Pin Number Circuit Circuit Function 1 57 (BK) Wiper Motor Ground (Park) 2 28 (BK/PK) Wiper Module to Wiper Motor (Park Switch) 3 65 (DG) Wiper Motor Power (Park Feed) 4 61 (Y/R) Wiper Motor Common (RUN) 5 56 (DB/O) Wiper Motor LO 6 58 (W) Wiper Motor HI
Windshield Wiper System The windshield wiper system consists of :
  • Windshield wiper motor (17508) (F-type).
  • Washer system.
  • Windshield wiper control module.
  • Turn signal and windshield wiper switch (13K359).
The windshield wiper control module is:
  • Located at the instrument panel fuse panel.
The windshield wiper motor is:
  • Attached to the cowl top extension (021A36) .
  • Connected to windshield wiper mounting arm and pivot shaft (17566) .
The turn signal and windshield wiper switch features a:
  • Rotary wiper switch.
  • Push type washer actuator.
OFF/Low/High Speed
  • Has a two-speed, permanent magnet, three brush electric windshield wiper motor .
  • The windshield wiper motor has a brush rigging that permits selection of low or high speed.
  • When the turn signal and windshield wiper switch is in the LO position, the common brush and the blue/orange wire brush are used, and the windshield wiper motor operates at low speed.
  • When the turn signal and windshield wiper switch is in the HI position, the common brush and the white wire brush are used.
  • In HI position, electric current will bypass a portion of the armature winding causing the windshield wiper motor to operate faster.
  • When the turn signal and windshield wiper switch is moved to the OFF position, the windshield wiper motor will continue at low speed until the park switch outer contacts open.
  • When the park switch contacts open, the windshield wiper motor stops in the park position.
Interval
When the turn signal and windshield wiper switch is in the interval position:
  • The wipers make single wipes separated by pauses.
  • The rotary switch is on the end of turn signal and windshield wiper switch .
  • The length of the pause can be set from approximately 1 to 17 seconds.
  • Length of pause decreases as the rotary switch is rotated away from off.
  • Length of pause increases as the rotary switch is rotated toward off.
While in the interval wiper mode:
  • It is normal to hear a slight click at the beginning of each on/pause cycle. NOTE: When using interval wipers, the first wipe may not occur until after a pause of up to 17 seconds.

May 27, 2009 | 1994 Ford Mustang

1 Answer

I have a 1992 dodge shadow.but the windshield wipers isn't working.I checked the motor is well,the terminal voltage is 12V,how can I continu to repair the 1992 dodge shadow's windshield wipers?


You posting is slightly confusing but I gather your windshield wipers stopped working.
The repair method is as follows;
) Check the fuse.
) Check the wiper motor. Turn the wipers on and listen for the hum of the motor.

If you hear the hum then the linkage has probably come loose. You will have to take the covers off
to get to the linkage for the wiper. You can either repair the parts, get salvage yard parts or replace with new part$.

If you do not hear the motor hum then you should verify electricity is getting to the motor. A simple
voltmeter can be used. If the motor is bad you can replace it. Call some auto supply stores for after-market motors or call salvage yards for parts.

May 07, 2009 | 1990 Dodge Shadow

1 Answer

I have a whistle or humming noise from the front of 05 Montana.


Put wide tape on different areas of the windshield edge as a test to see if the noise changes.Then you may know where the noise originates and can correct the noise.
Just by chance,it is a wind noise? and not a front wheel bearing going bad?which is common on these vehicles and can create a humming at different speeds.Next time when the hum shows up turn the steering wheel slightly left and right at road speed and if you can change the hum,it's 99% a wheel bearing.

Apr 02, 2017 | 2001 Pontiac Montana

1 Answer

Windshield Wiper motor replaced, now wipers go wrong direction


This sounds like the park circuit is shorted.

Nov 25, 2008 | 1999 GMC Yukon

Not finding what you are looking for?
1997 GMC Jimmy Logo

223 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...