Question about 2005 Volkswagen New Beetle Convertible

1 Answer


Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Master
  • 4,793 Answers

Clear bathroom silicon works(applied carefully)

Posted on Aug 02, 2010


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

I have a 96 celica gt convertable. Is the rear quarter glass compatable with a lift back

The rear quarter glass is not the same, it's made specifically for the convertible version.

Jul 21, 2017 | Toyota Celica Cars & Trucks

1 Answer

Sebring window

Look into window guide clips. These push the glass against the rubber

Oct 28, 2013 | Cars & Trucks

1 Answer

How to put plexi-glass in convertable top

That requires allot of skill and special equipment.

Jun 15, 2012 | 2001 Saab 9-3

1 Answer

How do you take the tint off the back window on my convertable?

unles its the actual glass thats tinted you should be able to peel it off..

Nov 06, 2011 | 1992 Volkswagen Cabriolet

1 Answer

Hi where dose the ariel fit for my telephone.. jaguar xkr convertable on a v plate. are there any diagrams i can use... regards kevin

Most antenna will be mounted on the front windscreen frame toward the top as to boost reception. It can be mounted on the side to camouflage it against the trim. Be sure to leave about 1/2 inch from the edge of the glass as to not crack it. And use a rubber gasket to seal the hole where the wire enters the body to prevent leaks. Threading the wire leads can be done using a thin coat hanger, opened to it's length, as a long threader. It will allow you to pull the wire down to the phone base.

Oct 15, 2009 | 2003 Jaguar Xkr

1 Answer

How do i disassemble the winsheild in my car?

Unless you have done this before or have someone with you who has I would highly reccomend having a glass shop do it.Its not all that complicated but if not done correctly the new glass will leak or you could damage the roof pillar,but i will tell you how it's done.First thing is to remove the trim from around the windshield,take a putty knife or other thin flat tool and slide it under the trim from the glass side and gently pry up,the trim should start pulling free,look for where the trim overlaps itself and pull these pieces first.Next take a sharp knife and carefully slide it between the glass and the seal and start cutting the seal free,you'll need a second person one on each side lift the glass and walk towards the front of the car.Now start pulling the seal away from the sheet metal,if it wants to stick a hair dryer should make it easier.Now the fun part,you got to clean any residue from the seal off,100% of it,if you leave any residue the new seal will not seal properly and it will leak,methanal or a strong isapropyl alcohol will work well for this and leaves no residue.Prep the new glass by cleaning the sealing area with alcohol,install the new seal on the car,be careful not to touch the adhesive on the seal,the oils from your skin will foul it and cause it to not seal properly.Now the most important part,you'll need someone to help you and set of glass cups(large suction cups with handles,if you have a Harbor freight tools nearby they ussually have them in stock)they're not neccesary but will make the job easier,attach the cups or pick the glass up by the very edge,one person on each side and walk up the front of the car,line the glass up being very careful not to let the glass touch the seal,once it's lined up set the glass as evenly as possible on the seal,you have to get it right the first time,once the glass touches the seal its going to stick and pulling the glass back off will more than likely ruin the seal.Once the glass is in place use a towel to rub down each edge and fully set the seal,install the trim and your done.Hope this helps,like I said I would highly reccomned having a glass shop do the install as they have the experience and the tools to do the job.

Apr 20, 2009 | Porsche Carrera Cars & Trucks

1 Answer

Rear sliding glass window

If u r going to buy a new one, instructions will be included, if u have plans to purchase a used one from a salvage yard, they aren't too difficult to install, the worst part is removing the old glass, and that's already done! Rubber glass seal around outside should be in place, put a rope inside the seal (where the glass will go) leaving a couple of feet or more hanging out at the end. Put the glass in between seal edges as much as you can w/out forcing. W/ a helper, slowly pull the rope out as u push the glass into the seal, the rope pulls back the seal so the glass can slide into the channel. If u have any trouble, don't insert the rope all the way around, this way more of the glass will fit in the rubber channel (seal). Good luck, let me know how it works for u. countrycurt0

Oct 09, 2008 | 2000 Dodge Dakota Quad Cab

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

52 people viewed this question

Ask a Question

Usually answered in minutes!

Top Volkswagen Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers


Level 3 Expert

81400 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8841 Answers

Are you a Volkswagen Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides