Question about 2009 Honda Accord

1 Answer

I Installed a new door glass (front passenger side) When I roll up the window on auto it goes to the top then comes back about 3 inches by itself and stops is there a way to set the door glass to stop doing this.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 4,793 Answers

Its called auto rollback(to stop kids getting thier fingers caight)it will reset itself(eventually)if you use the normal switch and then turn off the ignition when closed(you may have to do this a couple of times)

Posted on Aug 02, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1995 Ford Taurus front passenger window went down and won't roll up


Remove the switch panel and check to see there is 12V power there.. If there is Push the switch and see if the power comes out of it to drive the motor, if the power is not present check the wire back looking for the short.. usually if the power is missing none of the windows will work. look where the wires come out the door post to the door. look at fuses, If there is power and it does not come through the switch when you push the switch. the switch might be bad. in which case jump the switch to roll window up and buy a new switch (rock auto.com) if you apply 12v power and the window still will not go up.. you will need to replace the motor. not a hard job. you must remove door panel and remove regulator and motor and replace and reinstall. either junk yard part, craigslist part or new at Rock auto.. Post a comment and let us know what happens.

Aug 19, 2014 | 1995 Ford Taurus

1 Answer

Just replaced passenger front window on the 2001 v70. Do not remember if window stops an inch down or does it go all the way down?


I am not exactly sure on this model but most of the time the power windows on the front doors go down all the way. I would check the right passenger side door if it goes all the way down, then most likely the drivers side door should also. Usually the rear windows go down and stop an inch from being all the way down. Some cars are set up to lower the front windows only an inch then by pressing the window down button again, they will continue to roll all the way down.

Jan 02, 2010 | 2001 Volvo V70

1 Answer

Replaced passenger side door glass. When you use


What you need to do to initialize the window is remove the window motor from the regulator. Plug it into the car by itself, then press up on the switch until it turns four times. Then hold the switch down for four turns, then put motor back into the regulator, and assemble back into the door. to make sure the motor spins correctly four times I make a tooth on the gear with a marker.

Oct 13, 2009 | 2000 Lexus RX 300

1 Answer

The rear passenger side window seems to be coming off at the front side. I can tell if the rubber is torn or if it just need to be pushed back together.


sounds like the track has been dismounted....try to pull off the inside door panel and look for any missing or broken bolts on the track itself... the track protrudes down to keep the window on track....if this is not a problem look at the glass itself...roll the window down a little to see the bottom of the glass. makes sure all of the mounting brackets are in place and secure..

Aug 12, 2009 | 1999 Chevrolet Silverado 1500

1 Answer

04 taurus Power Windows, passanger side goes down, not up, new mo


It is most likely the switch itself. since the down works that means that there is power going to the switch. So, the up position switch is probably worn out.

Jul 23, 2009 | 2004 Ford Taurus

1 Answer

Power window problem. engauges then disenguages


Section 01-11: Glass, Frames and Mechanisms 1997 Windstar Workshop Manual REMOVAL AND INSTALLATION Door Glass and Regulator, Power Windows Removal
svw~us~en~file=ani_caut.gif~gen~ref.gif WARNING: IF THE REGULATOR COUNTERBALANCE SPRING MUST BE REMOVED OR REPLACED FOR ANY REASON, MAKE SURE THAT THE REGULATOR ARMS ARE IN A FIXED POSITION PRIOR TO REMOVAL TO PREVENT POSSIBLE INJURY DURING C-SPRING UNWIND.
  1. Remove front door trim panel (23942) and front door inside panel sound insulator (20394). Refer to Section 01-05 .
  1. Remove inside door belt weatherstrip.
  1. Remove front door window glass (21410) as described in this section.
  1. Remove two nut and washer assemblies attaching the window regulator equalizer arm bracket (23230).
  1. Remove four rivets retaining the front door window regulator base plate to door inner panel.
  1. Remove front door window regulator (23200) and front door window channel bracket (23288) from vehicle.
  1. Working on a bench, carefully bend tab flat to remove front door window regulator arm slides from front door window channel bracket.
  1. NOTE: Use care not to break tab; if tab is cracked or broken, replace front door window channel bracket. Make sure rubber bumper is installed properly on new front door window channel bracket, if replacement is made.

    Install new front door window regulator arm plastic guides into front door window channel bracket and bend tab back to 90 degrees.


    a9ef3ee.gif

Installation
NOTE: The front door window channel bracket and window regulator electric drive (23394) are installed into the vehicle as one assembly. The front door window channel bracket may be disassembled from the window regulator electric drive as described in Door Glass and Regulator, Power Windows .

  1. Install window regulator electric drive with preassembled front door window channel bracket into vehicle. Set the regulator base plate to door inner panel using base plate locator tab as a guide.
  1. NOTE: Two 1/4-20 x 1 inch bolts and two 1/4-20 nut and washer assemblies may be used as alternates for glass retention. However, torque must not exceed 4-7 Nm (35-44 lb-in). Equivalent metric retainers may be used.

    Install four rivets to retain front door window regulator to door inner panel.
  1. Install window regulator equalizer arm bracket.
  1. Lower front door window regulator arms to access holes in door inner panel. Install front door window glass as outlined.
  1. Install inside door belt weatherstrip.
  1. Adjust front door window glass to make sure it is properly aligned with glass run. Check window for smooth operation.
  1. Install front door trim panel and front door inside panel sound insulator. Refer to Section 01-05 .


    Door Glass and Regulator
ac1dac5.gif

Item Part Number Description 1 21410 Front Door Window Glass 2 23288 Front Door Window Channel Bracket 3 23394 Window Regulator Electric Drive 4 23230 Window Regulator Equalizer Arm Bracket 5 222A00 Front Door Glass Run Latch Side Retainer 6 N621906-S36 Nut and Washer 7 N800510-S36 Screw 8 23200 Front Door Window Regulator 9 W525172-S Rivet 10 W525175-S Rivet 11 — Wire Connector (Part of 14630 Wire Assembly) A — Tighten to 7-10 Nm (62-89 Lb-In)

Apr 13, 2009 | 1997 Ford Windstar

1 Answer

Front passenger power window does not work properly.


Take it to an Auto glass place and they can fix that problem.
If your going to try it you need to remove the inside door panel and look at the window rail fram and check the fasteners that hold the glass to the mounting brace. Inspect the guild rails for the window for any damages and worn parts. 
After inspecting and re tighten all the nut's and bolts and glass lines up. Just put things back together like new. Good luck and buy new door clips for the panel since they break easy.

Apr 07, 2009 | Chevrolet Blazer Cars & Trucks

Not finding what you are looking for?
2009 Honda Accord Logo

Related Topics:

111 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...