Question about 1995 Ford F250

Open Question

How do I remove the right front axle from differential on 95 f250 4x4 for new joint?

Posted by on

Ad

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 39 Answers

SOURCE: 95 f-250 right front stub shaft removal

I think if you put a pry bar behind the knuckle and give it a quick bump it will just pop out it has a ring on the inside that holds it in. Just uses pressure to keep it in place I will look in a few but I am sure that is what to do.

Posted on Jan 02, 2009

Ad
  • 1 Answer

SOURCE: remove front axle from differential on 2003 dodge ram

That works fine on a relatively new vehicle but one that has run in salt etc you'll save a lot of time if you remove the steering knuckle completey by separating lower ball joint and outer tie rod end ball joint and bring the whole steering knuckle to a bench to separate the hub/bearing. Soak everything with penetrant, loosen the bolts a few turns and try hitting right on the bolt heads. I also made a very sharp wedge from a chisel and rammed it hard on the other side to seoarate the hub. It will finally come apart then you'll see all the **** that was binding it due to an alumininum knuckle re-acting with a steel hub. Clean the hole and grease everything and fit new bearings

Posted on Feb 15, 2009

SUPERMAN_B_1
  • 294 Answers

SOURCE: REPLACING LOWER BALL JOINTS ON 2000 FORD F250 4X4 7.3L DIESEL

hello,yes you do have to take the hub off to replace the ball joint with the ball joint being on the back side of the hub. hope this helps and please rate this.

Posted on Mar 15, 2009

  • 166 Answers

SOURCE: How do I remove the front axle shafts in a 2003 Dodge 2500 4x4?

they just pop out. i get behind then and pop them out with a screw driver or small pry bar

Posted on Jun 04, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I remove the spindle axle on a 2001 dodge ram 1500 2wd? And what is the name of it exactly?


The spindle is what holds the front tires on. The axle is what holds the rear tires on. To remove the spindle, you have to remove the brake caliper first the remove the ball joint nuts. hit the spindle were the ball joints go in. The shock will release the ball joints. To remove the axles, you have to remove the differential plate, spin the differential until you see the bolt that locks the center pin in. remove both. push in the axle and remove the C clip. pull the axle out.

Oct 15, 2016 | 2001 Dodge Ram 1500 Truck 2WD

1 Answer

How to remove axle from front of 1998 windstar


  1. Raise and support the vehicle safely.
  2. Remove the front wheels.
  3. Insert a steel rod into the brake rotor to prevent the rotor from turning and loosen the axle wheel hub nut. Discard the nut.
  4. Remove the ball joint-to-front wheel knuckle retaining nut. Drive the bolt out of the front wheel knuckle using a punch and hammer.
  5. Remove the front brake anti-lock sensor and position it out of the way.
  6. Separate the ball joint from the front wheel knuckle using a prybar. Position the end of the prybar outside of the bushing pocket to avoid damage to the bushing.
Use care to prevent damage to the front wheel driveshaft joint boot.
  1. Remove the stabilizer bar link at the front stabilizer bar.
Make sure the CV-joint puller does not contact the transaxle shaft speed sensor. Damage to the sensor will result.
  1. Install a CV-Joint Puller (T86P-3514-A1) or equivalent between the inboard CV-joint and the transaxle case.
  2. Install a CV-Joint Extension (T86P-3514-A2) or equivalent into the puller and hand-tighten.
  3. Using an impact slide hammer, remove the driveshaft from the transaxle.
Do not allow the front wheel driveshaft and joint to hang unsupported. Damage to the front wheel driveshaft joint may result. Do not wrap wire around the front wheel driveshaft joint boot. Damage to the boot may result.
  1. Support the end of the driveshaft and joint assembly by suspending it from the chassis using a length of wire.
Never use a hammer to separate the outboard front wheel driveshaft joint from the wheel hub. Damage to the outboard front wheel driveshaft joint threads and internal components may result.
  1. Separate the outboard front wheel driveshaft joint from the wheel hub using a Front Hub Remover/Replacer (T81P-1104-C) or equivalent. Make sure the hub remover adapter is fully threaded onto the hub stud.
Do not move the vehicle without the outboard CV-joint properly installed, as damage to the bearing may occur.
  1. Remove the front wheel driveshaft and joint assembly from the vehicle.
To install:
Do not reuse the retainer circlip. A new circlip must be installed each time the inboard CV-joint stub shaft is installed into the transaxle differential.
  1. Install a new retainer circlip on the inboard CV-joint stub shaft by starting one end in the groove and working the retainer circlip over the inboard shaft housing end and into the groove. This will avoid overexpanding the circlip.
A non-metallic mallet may be used to aid in seating the retainer circlip into the differential side gear groove. If a mallet is necessary, tap only on the outboard CV-joint stub shaft.
  1. Carefully align the splines of the inboard CV-joint stub shaft housing with the splines in the differential. Exerting some force, push the inboard CV-joint stub shaft housing into the differential until the retainer circlip is felt to seat in the differential side gear. Use care to prevent damage to the inboard CV-joint stub shaft and transaxle seal.
  2. Carefully align the splines of the outboard front wheel driveshaft joint with the splines in the wheel hub, and push the shaft into the wheel hub as far as possible.
  3. Temporarily fasten the front disc brake rotor to the wheel hub with washers and two lug nuts. Insert a steel rod into the front disc brake rotor and rotate clockwise to contact the front wheel knuckle, to prevent the front disc brake rotor from turning during front wheel driveshaft and joint installation.
A new front axle wheel hub retaining nut must be installed.
  1. Manually thread the front axle wheel hub retaining nut onto the outboard CV-joint stub shaft housing as far as possible.
A new bolt and nut must be used to connect the front suspension arm to the knuckle.
  1. Connect the front suspension lower arm to the front wheel knuckle. Tighten the nut and bolt to 40-55 ft. lbs. (54-74 Nm).
  2. Install the front brake anti-lock sensor.
  3. Connect the front stabilizer bar link and tighten to 35-45 ft. lbs. (47-65 Nm).
Do not use power or impact tools to tighten the hub nut.
  1. Tighten the front axle wheel hub retaining nut to 157-212 ft. lbs. (213-287 Nm).
  2. Install the front wheels and lower the vehicle.
  3. Using the recommended type of fluid, fill the transaxle to the proper level.

Jul 07, 2014 | 1998 Ford Windstar

1 Answer

97 ford explorer/bad front differential..can I remove it completly with the cv joints and let front wheels freewheel?


Yes is the short answer. Did you blow the gears in your front differential or you going to put a whole new pumpkin in? If you are replacing the entire pumpkin drain it first. Then make sure to support it with a transmission jack first. Remove the tires. Then remover the CV axles and lower the pumpkin. Your vehicle requires a 75w90 synthetic axle lube for a refill. Good luck.

Mar 06, 2011 | 1997 Ford Explorer AWD

1 Answer

95 passport shakes when4x4 is engaged during acceleration


Bad u-joints at front driveline and/or u-joints at axle connection from behind rotors- going into front differential. Need new u-joints at either the driveline front and back (going into differential or to Transfer case) or the Left and Right side axles going into the differential. Put Locking (or "Lock-outs) hubs on front axles... WARN brand are best... about $75 a pair and you can do it yourself, easily.

Dec 28, 2009 | 1995 Honda Passport

1 Answer

Do I have to remove the control arm to replace the half shaft on a 2005 Ford Freestar?


no, here's the procedure for 2002 windstar, should be similar. please rate, thanks.

NOTE: This procedure applies to both the LH and RH halfshaft assemblies.
  1. Raise and support the vehicle. For additional information, refer to Section 100-02 .
  1. Remove the front wheel and tire assembly. For additional information, refer to Section 204-04 .
  1. Insert a steel rod in the brake disc to prevent the halfshaft from turning while removing the front axle wheel end nut.
  1. s2w~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: The front axle wheel end nut is a torque prevailing design nut. Do not reuse it.
    Remove the nut and washer.
    • Remove the steel rod in the brake disc.
  1. s2w~us~en~file=ani_caut.gif~gen~ref.gif WARNING: Remove or tape the brake pads to prevent them from falling out of the anchor plate.
    s2w~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: To prevent damage to the brake hose, do not allow the disc brake caliper to hang suspended from the hose.
    Remove the bolts and position the disc brake caliper aside.
  1. Remove the front brake anti-lock sensor harness from the clip.
  1. Remove and discard the nut and bolt.
    • If necessary, use a punch and a hammer to drive the bolt out of the knuckle.
  1. s2w~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Position the end of the pry bar outside the bushing pocket to avoid damage to the bushing.
    s2w~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not damage the front wheel driveshaft joint boot (3A331).
    Separate the front suspension lower arm from the knuckle.
  1. s2w~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Never use a hammer to separate the front wheel driveshaft joint (3B413) from the wheel hub. Damage to the joint threads and internal components can result.
    Using the special tool, press on the front wheel driveshaft joint until it is loose in the wheel hub.
  1. Rotate the front wheel knuckle rearward, while pulling it outward at the bottom and remove the front wheel driveshaft joint from the wheel hub.
  1. Using a pry bar, separate the inboard CV joint housing assembly (3B436) (3B437) from the transaxle.
  1. s2w~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not damage the differential seal.
    Remove the halfshaft assembly with both hands.
Installation
  1. Lubricate the differential seal.
    • Use MERCON® V Automatic Transmission Fluid XT-5-QM or equivalent meeting MERCON® V specifications.
  1. s2w~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Install a new circlip every time you remove the halfshaft from the vehicle.
    On the RH side halfshaft only, install a new circlip in the groove in the inboard CV joint stub shaft.
    • Start one end in the groove and work the circlip over the shaft and into the groove. This will prevent the circlip from over-expanding.
  1. s2w~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not damage the inboard CV joint housing assembly and the differential seal.
    NOTE: If necessary, use a non-metallic mallet to aid in seating the circlip in the differential side gear groove (RH) or inboard CV joint housing (LH). Tap only on the outboard front wheel driveshaft joint.
    Align the inboard CV joint housing splines with the differential side gear splines (RH) or output shaft splines (LH), and push the inboard CV joint housing assembly inward until the circlip seats in the differential side gear (RH) or inboard CV joint housing (LH).
  1. Align the front wheel driveshaft joint splines and the wheel hub splines, and push the joint into the wheel hub as far as possible.
  1. Install the washer and the old nut. Using the old nut, seat the front wheel driveshaft joint in the hub. Remove the old nut and discard it.
  1. Connect the suspension lower arm to the knuckle.
  1. s2w~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Install a new bolt and nut.
    Install the new bolt and nut.
  1. Insert a steel rod in the brake disc to prevent the halfshaft from turning while installing the new front axle wheel end nut.
  1. Apply a small patch of Loctite 242 or equivalent meeting Ford specification WSK-M2G351-A5 to the last five front wheel driveshaft joint threads.
  1. s2w~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Install and tighten the new front axle wheel end nut to specification in a continuous rotation. Stopping the rotation during installation will cause the nylon lock to set incorrectly. This will cause incorrect torque readings while tightening the nut, and lead to bearing failure. Always install a new front axle wheel end nut after loosening the nut, or when the nut has not been installed to specification in a continuous rotation.
    Install and tighten the new nut to specification in a continuous rotation.
    • Remove the steel rod from the brake disc.
  1. Position the disc brake caliper and install the bolts.
  1. Install the front brake anti-lock sensor harness in the clip.
  1. Install the wheel and tire assembly. For additional information, refer to Section 204-04 .
  1. Lower the vehicle.
  1. Check and, if necessary, fill the transaxle to the correct level with the specified fluid. For additional information, refer to Section 307-01 .

Nov 15, 2009 | 2005 Ford Freestar

3 Answers

My front differential is leaking!


I cannot see it, but I am guessing that you need to replace your axle seal. To do this,you have to pull your CV shaft out. Remove the tire, remove the caliper from the top of the rotor. Using a hammer on the back, remove the rotor. Take off the spindle (axle) nut, separate the axle (CV shaft) from the hub. Replace seal. It should pop right out. Good luck!

Aug 05, 2009 | GMC Sierra 1500 Cars & Trucks

3 Answers

Remove front axle from differential on 2003 dodge ram


That works fine on a relatively new vehicle but one that has run in salt etc you'll save a lot of time if you remove the steering knuckle completey by separating lower ball joint and outer tie rod end ball joint and bring the whole steering knuckle to a bench to separate the hub/bearing. Soak everything with penetrant, loosen the bolts a few turns and try hitting right on the bolt heads. I also made a very sharp wedge from a chisel and rammed it hard on the other side to seoarate the hub. It will finally come apart then you'll see all the **** that was binding it due to an alumininum knuckle re-acting with a steel hub. Clean the hole and grease everything and fit new bearings

Jan 06, 2009 | Dodge Ram 1500 Cars & Trucks

1 Answer

95 f-250 right front stub shaft removal


I think if you put a pry bar behind the knuckle and give it a quick bump it will just pop out it has a ring on the inside that holds it in. Just uses pressure to keep it in place I will look in a few but I am sure that is what to do.

Jan 02, 2009 | 1995 Ford F250

1 Answer

Cannot remove the front drive shaft


you have to remove the differential cover this will exp[ose the carfrier gear. you have to remove the end bearing caps make sure you keep them in order they have to be replaced the same way . there is a retaining ring on each axle that must be removed before you can remove the axle. remember wwhen you assemble it back that you replace those rings on the axles. please rate this........thanks

Sep 23, 2008 | 1997 GMC Jimmy

1 Answer

Front axle how to remove half shaft


Hi.. The step to remove the front Axles of you Vitara.
Raise and support Vehicle . Remove front wheel,
Drain Diff,fluid,
Remove Locking Hub if is equipaded,
Remove Circle clip from axle shaft
On right side of Vehicle, Remove the Stabilizer Little ball joint nut. Remove castle nut Front Tie rod end,
Remove mounting bolts from brake calipper,
Remove Calipper from steering knuckle and wire a side.
Remove Stud Nut from steering knuckle,
Support Lower suspension arm with a jack,
Remove lower strut bracket bolt ,
Lower jack and disconnect Knuckle from lower suspension crontrol arm,
Pull Outler joint from Hub.
Use Large screwdriver or Prybar To pry Right inner joint from differential, The axle will go out making a little froce with the prybar,
To remove the left side,
Remove mounting bolt from inner joint flange,
Pull out axle from hub.

To reinstall just reverse the prosses.

I hope this help on your job...
Thank you for use fixya....


Aug 18, 2008 | 1999 Suzuki Vitara

Not finding what you are looking for?
1995 Ford F250 Logo

Related Topics:

163 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5520 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...