Question about 2000 Chevrolet Venture

1 Answer

Transmision removal Can I pull the trany out the bottom? Or do I have to pull it out the top along with the motor?

Posted by on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 5 achievements.


    An expert that has over 500 points.


    An expert whose answer got voted for 20 times.

  • Expert
  • 178 Answers

You pull that out the bottom but you have to take the sub frame off also the engine has to be supported with a support tool that goes to each fender it's a big job if youve never done this before.

Posted on Aug 02, 2010


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

2 Answers

Is it easier to pull the motor when replacing the transmision, or is there a way i can replace it from under the car.

You can replace from underside without pulling engine, just make sure is raised at least 18 inches give yourself room to work and for clearance.

Feb 18, 2011 | 1999 Saturn SL

1 Answer

Had to change the the bottom oil seal behind the top converter to fit the transmission back to the engine what should i do to get it on to the top converter

first the converter have to be in the transmision be sure all the way hold it on place use a tin piece of wire lift the trani close to engine yo be more easy use long bolts no head on the top of the engine long enoug to remove them after you put the other two dont tight them until youare sure the converter turn freely remove the wire holdind the converter

Dec 16, 2010 | 1990 Toyota Corolla

1 Answer

How do you check and add transmition fluid on a 2006 VW Passat

The best way is on a lift, the engine must be warm and car level, with the motor running remove the plug on the bottom of the trany pan, oil should leak out a little, this means its full if not then on top side of trany remove the fill pull cap and add from there until it starts to run out of the plug, theres a long tube in the pan and oil will only run out when level is higher than the tube. hope this helps.f781d2f.png75884bb.png1d36d6b.png

Oct 08, 2010 | 2006 Volkswagen Passat

2 Answers

Need to pull engine, 4.3, on 97 chevy blazer 4x4 but 3 trany to engine bolts are not accessible. is it standard practice to pull trans at same time?

what you can do is to remove the motor mounts
and that may let the motor lay down more to get to the top bolts on the trans
I dont think that you can pull the trans and transfer case with it

Jan 10, 2010 | 1997 Chevrolet Blazer

1 Answer

Won't shift in to second gear or drive. Only in first and reverse. '93 ford taurus, v6 auto.

I am very sorry to say the trany is bad. Two ways to fix. Replace the trany yourself with a new one or have your local tany repair shop rebuild it. Dollar amount is about the same. The only way to remove the tany is by pulling the engine and trany out of the top as one unit. If you work on it full time, expect and expert to do it in four days. Day one, disconnect everything. Day two, pull engine and trany out, seperate the two and replace with new one, put completed unit back in. Day three hook everything back up. Day four, fix what ever you forgot to do!! Heavy tools set needed along with jacks, jack stands, and engine lift. Hope this helps.

Shain Hamrick

Jan 02, 2010 | 1993 Ford Taurus

2 Answers

How do i check my transmission fluid? for a 2000

Set the parking brake and put a block on at least one wheel. Pop the hood and find the Transmission dipstick. Start the engine and shift the gear shift into neutral. Pull the dipstick, wipe it with a clean rag, put it back in, pull it out and read it.

Oct 20, 2009 | 2000 Pontiac Grand Am GT

1 Answer

How do you remove transmission in 1996 park avenue?

Drain pan, take out axles, put motor support on the top to hold motor while pulling. Disconnect trany lines, put trany jack under transmission. The K frame needs to come out completely that is why you need the motor support chain to the motor top.Take bolt out of bell housing. Disconnect all connectors and cables. Transmission mount will need to be removed on passenger side. You need to take the 4 bolts out of the can jump the starter if you have a remote switch or however you would like to do it to gain access to the converter bolts; otherwise, you will need to turn it with a screwdriver until you get all of the bolts out. Then you take the transmission jack and begin to pull the trany side ways until it clears the engine and let it down and that should do it...there are a few obvious things that will need to be taken out on top of the motor, even a few that I didn't mention on the bottom, but for the most part that should do it.

Jun 15, 2009 | 1996 Buick Park Avenue

1 Answer

Getting auto trany out

to pull the top transmision bolts you need about 3 feet of extentions so your ratchet is backat the tail stock of the transmision. or drop the trans mount and allow the trans to lowwer to the ground . you may want to remove the fan so it does not hit the radiator. as well as use a floor jack to lower the trans. good luck

Jan 19, 2009 | 1999 GMC Sonoma

1 Answer

Transmission needs replacement in '95 dodge stratus with 2.4l

saffety is n0 1 this is a major work you neded to be careful, here some sugestions 1 raise the car with a car jack ind the front of car 2 instal 2 jack stands eacht side 3 bloc the rear weels pull on hand brake 4 disconect the batterie drain the transmision . if there is no drain plug on the carter, disconect one of the trani line and crank the engine on until all the fluid goes out.5remove the tires and the axles unplug all the electircal attachements to the trani,unhook the shift cable 6 remove the torque converter bolts or nuts 7remove all the bolts attaching the trany to the engine make sure you have a floor jack to receive the trany when it fail down do not work under the car or check it to mutch

Dec 22, 2008 | 1995 Dodge Stratus

Not finding what you are looking for?
2000 Chevrolet Venture Logo

Related Topics:

32 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts


Level 3 Expert

81400 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides