Question about 2001 Ford Escape
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
haev some one help you by pushing on the door wjile you try to open it. it needs little force. what happen is the catch is off align, when you moove the furnitures.
you have to look at the lock and figure out how much is off and correct it.
Posted on Nov 18, 2008
First check if the vent cap is plugged, to do that find the T shaped object on the housing spin the top of the tee if it does not move freely then pull it off and clean it. If it's leaking out of the front seal it's the drive line seal is leaking and will have to remove the drive line put Emergency brake on and block wheels and loosen 24MM nut to get to the seal you have to pop the seal off with a screw driver and you have to replace the crush bearing when you do this. However recommend you leave that to a professional or purchase a www.alldatadiy.com susbscription for your car so you know how to set up the bearings if it is needed, you will also have to have a tork wrench to tork the nut down. You will a new Nut for the pintal shaft that comes out of the front of the axle as well the nut is nut reusable once you remove it. Another note you have to have air impact to get the nut off or a torch t heat it just enoungh to get it off but warning fuel tank is right there so if your all thumbs don't mess with it. If it's not leaking from the front seal and is leaking from the back side of the differential then you must drain the oil and replace the gasket on the rear plate, this job is not to difficult but you mus be sue you put silicone on the cover and gasket and put silicone on the bolts as you put them in because if not you will get bolt leakage, these also require a tork wrench. the front seal nut and crush bearing will cost $45.00 the rear will cost $15.00 for the silicone and gasket. And warning if the differtal is leaking from the seal it is quite possible that the bearings will need to be replaced or set up again and this takes experince or it could cost you $750.00 to rebuild the differital. hope this helps.
Posted on Oct 09, 2009
B1 means the sensor is located on the same bank of the engine that has the #1 cylinder. B2 is located on the opposite bank.
S1 means the sensor is located BEFORE the catalytic converter
S2 means the sensor is located AFTER the catalytic converter
You didn't say which engine you have, so I've included the diagrams of both 4 cyl and 6 cyl so you can see the banks
Posted on Oct 20, 2009
the cable of the knob is moved out it wont cost you much , take car to work shop and it will take hardly 30 to 45 min, it will get corrected.thanks.
Posted on Feb 18, 2010
Testimonial: "Thank you!"
Tips for a great answer:
Apr 15, 2014 | 2009 Ford Escape
Apr 11, 2013 | 2010 Ford Escape XLT
Jul 07, 2012 | 2001 Ford Escape
Jul 03, 2011 | 2001 Ford Escape
Feb 22, 2011 | 2002 Ford Escape
Jan 18, 2011 | 2005 Ford Escape
Sep 06, 2010 | 2001 Ford Escape
Sep 08, 2009 | 2001 Ford Escape
May 29, 2009 | 2001 Ford Escape
Apr 09, 2009 | 2002 Ford Escape
98 people viewed this question
Usually answered in minutes!