Question about 1993 Ford Ranger SuperCab

1 Answer

Should I take my '93 ford ranger to a transmission shop to replace the clutch?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 360 Answers

Hi, you should definitely take it to a transmission shop to replace the clutch, you will get the best of service like i did....

Take care

Posted on Aug 01, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have 93 Ford Ranger with a bad transmission is there any year Ranger that will interchange with it


run the fault codes first as many so called bad transmission are electronic problem related
check with an automatic /manual transmission repair professional as there are many models that use the same transmission

May 24, 2018 | Ford Cars & Trucks

1 Answer

98 ford ranger 4wd manual transmission will onl start when i pop start in 2nd gear


Check to make sure the safety switches are engaging. One on the clutch, one in the shifter and/or transmission.

Sep 14, 2017 | 1998 Ford Ranger SuperCab

1 Answer

How to take out clutch in a 93 ford ranger 3.0 standerd 4+4


In general terms, the transmission has to come out to get to the clutch.
If you need step by step directions I would suggest a repair book.

Aug 04, 2012 | Ford Cars & Trucks

1 Answer

I need to replace my clutch slave cylinder in my 1993 ford ranger


the slave cylinder on the 90's models rangers is inside the transmission. you have to pull the transmission and its mounted around the output shaft highly recommended to replace the clutch since its out to save for troubles later

May 05, 2011 | Ford Ranger Cars & Trucks

1 Answer

My 2001 ford ranger clutch does not work


common problem with these transmissions have the shift fork replaced its probably aluminum a little is alot for those for wear

Jul 25, 2010 | 2001 Ford Ranger Regular Cab

1 Answer

Changing clutch on a 2003 ford ranger how do I


Well to start, you need to remove the shifter from the transmission. Then remove the driveshaft. Then unplug the plugs from the side of the transmission and disconnect the clutch fluid line. Then remove the crossmember. Unbolt the bellhousing bolts. Then have a friend help you remove the transmission. Then unbolt the clutch.

Jul 09, 2010 | 2003 Ford Ranger Regular Cab

1 Answer

Need to know will a 3.0 v6 out of a 93 fit in my


you will need to change engine and transmission along with the engine wiring harness and computer also if your 2.3 was carburetorated you will need the fuel pump out of the fuel tank .
also remove the engine frame mounts and the transmission cross-member from the 93 might also need changed.

Nov 11, 2009 | 1986 Ford Ranger 2WD

3 Answers

2001 Ford ranger edge. The gears won't change.


The trans will need to come out. While your at it, just replace the clutch assembly, rear main oil seal, resurface the flywheel, and the clutch master cyl. Its not really a job you should do, find a repair shop to handle it.

Nov 06, 2009 | Ford Edge Cars & Trucks

1 Answer

Need clutch replacement directions for Ford Ranger


Remove drive shaft,remove crossmember under transmission.Remove transmission and diconnect linkage.Remove bell housing,and clutch berring assembely.Remove bolts on pressure plate.Once this is done.Remove fly wheel for machineing.you will need a pilot shaft to alighn clutch assemblely.Possible one will come with new clutch and pressure plate.Reverse assemblely in same order remember to torque all your bolts with torque wrench.Take your time.

Apr 19, 2009 | 1994 Ford Ranger Supercab

2 Answers

2002 Ford Ranger Clutch Problems


It's not the clutch, it is the clutch slave cylinder. Check the fluid level in the clutch master cylinder and you will see that it will be empty. The problem is the trans has to be removed to replace it.

Jan 13, 2009 | 2002 Ford Ranger Regular Cab

Not finding what you are looking for?
1993 Ford Ranger SuperCab Logo

Related Topics:

138 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

Marvin
Marvin

Level 3 Expert

81400 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22359 Answers

gerry bissi

Level 3 Expert

4376 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...