Question about 1994 Oldsmobile Cutlass Supreme

2 Answers

Need advanced timing degree for 1969 cutlass 350 rocket could it be between 8-10 deg

Posted by on

Ad

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Oldsmobile Master
  • 22,246 Answers

1969 ,points and distributor ,,,, then unleaded petrol 95 i would set it to 6º at idle ,now as this vehicle was designed to run on leaded fuel with a higher compression than that used on modern cars you could use a lead substitute and set timing to 10º on idle ,now iam not sure if this vehicle had stellite coated valve seats and valves and only a dealer might know ,now if it hasnt got stellite valves and seats then you must use the lead substitute or the valves will burn out ,but if the negine does have stellite valves and seats then it will run quite happily on the unleaded fuel with the timing retarded a bit ,i mean i bet its a 4 litre or something so a slight loss of power will not be noticeable ,but a 998cc morris minor its quite a difference

Posted on Aug 01, 2010

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 3,301 Answers

Check this site for all your needs depending on which distributor you have http://www.442.com/tech/supertuning6970.html

Posted on Aug 02, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Cam specs on a 1967 Pontiac 400, 335 hp


Firebird App. Pontiac Part # Duration @ .050 Degrees Int/Exh Adv Duration Degrees Int/Exh Lobe Center Degrees Int/Exh Lobe Separation Angle Overlap Cam Lift Int/Exh Gross Lift Int/Exh
(1.5:1 Ratio Rocker) Gross Lift Int/Exh
(1.65:1 Ratio Rocker) 1977 TA6.6 549431 274/289 62 .249/.270 .374/.406 .411/.446 1978 TA6.6 10003402 273/289 54 .270/.271 .406/.407 .446/.448 1979 TA6.6 10003402 274/298 55 .249/.270 .374/.406 .411/.446 1967 400, 1968 350, 1973-76 400 w/ AT 9779066(E) OEM 200/210 273/282 106/116 111.25 55 .272/.271 .408/.407 .449/.448 1967-68 400HO w/ MT 9779067(P) OEM 200/213 273/289 113.5 54 .272/.271 .408/.407 .449/.448 1968 400 HO MT & RA-I AT, 1969 350 HO MT, 1969 400 MT, 1970
RA-III MT/AT, 1971-72 455 HO MT 9779068(S)
OEM 212/225 288/302 113/118 116 63 .272/.271 .408/.407 .449/.448 1967 RA MT/AT, 1968 RA-I MT,
(Some 1969 GTO RA-III MT) 9785744 (H)
OEM 224/236 301/313 112/119 115 76 .272/.271 .408/.407 .449/.448 1968-70 RA-II & RA-IV MT/AT 9794041
(T) OEM 230/240 308/320 112/115 114 87 .313/.313 .470/.470 .516/.516 (Stock in RAIV)

Sep 20, 2017 | Pontiac Cars & Trucks

1 Answer

1969 Oldsmobile 350 rocket HM I distributor firing order


Last I remember GM firing order was 1,8,4,3,6,5,7,2

Jul 24, 2016 | Oldsmobile Cars & Trucks

1 Answer

Distributor firing order for 1969 olds 350


1969 Oldsmobile Cutlass 5.7L 4BL OHV 8cyl


The Firing Order

.Firing order 1-8-4-3-6-5-7-2 ---------front ' 2 4 6 8 ' of ' ' distributor rotates counter vehicle ' 1 3 5 7 ' clockwise---------

Sep 16, 2013 | Oldsmobile Cutlass Supreme Cars & Trucks

1 Answer

1992 Chevrolet Tahoe timing


timing on the chevy motors do not very much.
most of the older 350's timing are set about 8 deg before top dead center. some california smog certified 350 timing were set back to 0 deg or, at top dead center. check under the hood for a smog decal. it should have the timing specs, or it might say "timing not adjustable" or N/A. if it is missing the decal i would set it at 8 deg, road drive it, and listen for enging pinging on accelerating under load. if no ping i would leave it at 8 deg,if there is slight pinging i would ****** the timing in 2 deg increments until the pining stops. i would stop if i reach reach 0 deg or top dead center.

Sep 12, 2012 | Cars & Trucks

1 Answer

1983 gmc jimmy 350 engine. no sticker in engine compartment. what is timing deg at what rpm ???


12 degrees was common for those engines at 650 rpms, but make sure that the engine is warm and disconnect the vaccum advance, which will probably require plugging the vaccum port at the carb.

Mar 30, 2011 | 1983 GMC Jimmy

1 Answer

Ing timming for a 1969 chev 427 390 hp


It's trial and error. If it's a stock points style ignition start with factory settings. If it's an aftermarket electronic ignition, you'll need to know how much vacuum, mechanical or electronic advance there is. Most street engines work best with around 32 to 36 degrees total advance. So you use a timing light to set basic timing at 10 to 14 degrees BTDC, and find out how much vaccum, mechanical or electronic advance there is by 4500 RPM ( it's usually best to have all the advance in by 3600 RPM for a street or strip car). Then reset idle speed and use a stopwatch to test 0 - 60 MPH times and go with what setting gives you the fastest time without pinging. Maybe even a couple more degrees retarded for street use on pump gas ( you can always bump it up a few degrees at the track or when using octane boosters).

Jul 21, 2009 | 1987 Chevrolet Nova

1 Answer

Vacuum advance for 350 olds rocket


There is a tube on the drivers side of the carb. facing the front of the engine. It only draws vacuum when you are giving it the gas. Is it a quadrajet? Get one from a 1970-1974 these are simple to operate.

Apr 18, 2009 | 1985 Buick Regal

2 Answers

Want to put 1994 chev 305 engine/tranny in 1982 olds cutlass


First off you have to determine if the original engine in the car is an olds engine or chevy or the buick V6, - if it has the Olds307 the starter will be on the drivers side do not replace it with a Chevy motor the trans wont bolt up and if you try to transplant the chevy trans and engine you are going to run into crossmember problems driveshaft issues and alot of grief - find an Olds Rocket 350 - the older the better - it will save time and money and the Olds 350's put out a hell of alot more horses than a chevy like almost 100 more STOCK!!, a and will take a beating, try to find one pre 1975 but mor common are the 1977 (the last year) - or take the 307 to a macine shop and have it made into a rocket 350 also a cheap route.

Nov 22, 2008 | 1983 Oldsmobile Cutlass Supreme

1 Answer

1990 full blazer ignition timing degrees


If the ECM is still in and working, "0" deg unplugged would be correct. But are the timing marks correct? If the marks are lined up statically on "0" deg. is the #1 piston at TDC? Also important is for the ECM to be happy with the feedback it gets from it's sensors so it is running "in loop" If the "check engine" light is on, it will run but poorly. Make sure all sensors are in place and connected properly.

Sep 27, 2008 | 1991 Chevrolet C1500

Not finding what you are looking for?
1994 Oldsmobile Cutlass Supreme Logo

311 people viewed this question

Ask a Question

Usually answered in minutes!

Top Oldsmobile Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8589 Answers

Are you an Oldsmobile Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...