Question about Isuzu Rodeo

1 Answer

Clutch went out on my isuzu rodeo 4+4, manual transmission, we are having trouble removing the clutch release bearing, do we need a special tool?? like the book says? it says clutch release bearing remover J-39207 or an equivalent.. Need help bad, my car is my job

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 130 Answers

Basically this all it it a long flat head screw driver that youll be able to use in a typicall way. heres the link check it out. hope this helps you. i done it with a long scredriver
http://ww2.justanswer.com/uploads/yoda413/2008-12-28_195135_passtrans.pdf

Posted on Aug 01, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

How to replace a clutch on 1990 Isuzu trooper.


QOD: are you dead SURE the slave is ok? moves .75 to 1inch and OK?
2wd or 4wd? not stated.?
no engine stated? v6 or i4?


the procedure is same on all 4wd cars/trucks(mostly)
some pull the engine , for sure if engine needs work,as most do
after 25 years,
or pull transfer case and trans,pulled at the bell.
depends too,if you like spending long time under car
or on top, bent over fenders. (and tools)
if engine out no need to drain 1 or 2 gear boxes..and links,console..endless details....4wd lots more....

the video above shows the odd DUCK, throw out bearing.
and is important to know all that,
why not get a service manual..>?or use mitchell's????

not too many 1990 on the road.
rare car and year.
done many jeeps and rice 4wd.
2.6L,, SACHs 9.5" clutch $120 ($300 is bs)
or
2.8 v6 SACHs 9.125" clutch. $170

see they are not the same.....
I like Sachs, as you can see.. china clones not.

do you know how to fit the flywheel pilot bushing
and inspect fly surface, ?

the staging on the 9 bolt PP is here

im online now at one famous site
and the install skips, pilot bearing,funny that.
a real service manual is far better.



clutch-3xydvjc2hsdtpbulwfi331lq-2-0.jpg

26a-3xydvjc2hsdtpbulwfi331lq-2-1.jpg slave to fork lever to above damage, at T/o bearing
trans mission pilot shaft tip wrecked, or spline wrecked?
or you wiggle said shaft and front bearing in the box is SHOT.?
flywheel warped, or?
just saying, ive seen it all there, every fail.
on some all those were bad, on many 25year old cars.

Jan 13, 2017 | 1990 Isuzu Trooper

1 Answer

How to remove accumulator on transmission on Isuzu Rodeo?


Planetisuzoo.com • View topic - Transmission Accumulator Piston Cover

forum.planetisuzoo.com/viewtopic.php?t=38884
Apr 2, 2010 - 20 posts - ‎8 authors Have any of you ever changed the Accumulator Piston Cover on the side of yourtransmission? ... 2001 Isuzu Rodeo LS :: 3.2L V6 Auto 4L30E >> clicky for pics << ... I got the kit, and I even scored the removal tool on eBay. 1991 Trooper Transmission Pan ...
26 posts
Mar 20, 2012
2000 Rodeo Transmission Fix
10 posts
Jun 25, 2011
Smoke coming from bottom of Isuzu ...
24 posts
May 21, 2011
TSB information
7 posts
Jul 23, 2007
More results from forum.planetisuzoo.com

isuzu rodeo transmission - YouTube

? 1:37
www.youtube.com/watch?v=CyJZQLwnfPY
Sep 3, 2013 - Uploaded by besiratabay
2001 isuzu rodeo transmission problems 2002 isuzu rodeo transmission 1999 isuzu rodeo transmission .

Oct 30, 2015 | Isuzu Rodeo Cars & Trucks

1 Answer

1997 isuzu rodeo transmission valve body ball bearing location


that will take a real isuzu full transmission FSM book.
or from the true maker, see that tag on the tranny?
it answer that. on most cars.
will say like Aisin mfg company model x. or ????????

there are 2 choices.

Mar 23, 2015 | 1997 Isuzu Rodeo

1 Answer

Manual 2WD Gear box won't come off back of motor,have undone all bell housing bolts including starter motor, any tips?


the MUA box? NOT THE T5R, so why not just say it????


may be the Fly wheel pilot bearing is seized.?

my guess you got to step 12 (12 = 1 below)
  1. Remove the slave cylinder heat protector. Unbolt and remove the slave cylinder. Don't disconnect the hydraulic line.
  2. Remove the slave cylinder dust covers.
  3. Matchmark the driveshafts at the flanges and remove them.
  4. Disconnect the reverse light switch, 4WD indicator switch, 1-2 and 3-4 indicator switch harness connectors.
  5. Disconnect the speed sensor harness connector.
  6. Remove the 2 harness clamps from the transmission case.
  7. Attach a chain hoist to the engine.
  8. Using a transmission jack, raise the transmission slightly. Remove the 2 rear transmission mounting nuts.
  9. Remove the center crossmember (8 bolts).
21 is for 4wd
1 below is 22
  1. Remove the 3 flywheel inspection cover bolts.
  2. Use clutch release bearing remover J-39207 or an equivalent pry tool to release the bearing from the pressure plate. Push the release fork toward the rear of the vehicle. Insert the tool between the release bearing and the pressure plate collar. Move the lever to the rear to pry.
  3. Raise the engine slightly with a chain hoist and remove the bolts and nuts securing the transmission to the engine.
  4. Carefully pull the transmission rearward. Lower the transmission from the vehicle.

I'd never do major work on any drive line with out the FSM at my side.
or a login acount at alldata.com
or fail big time, for $15 bucks, was it worth it, bet not.

Jul 03, 2014 | 1994 Isuzu Rodeo

1 Answer

How to replace clutch step by step on a toyota rav4 4wd


You need some very specialized tools to do that You'll need a jack to hold the transfer case once you remove all the bolts holding it to the transmission. Remove the drive shafts.Then you'll need to remove the transmission, again with a supporting jack. Once that has been accomplished , remove the bolts holding the clutch to the flywheel. I'd replace the pilot bearing in the flywheel that holds the input shaft to the gearbox before proceeding. There are special tools available to do that. Now assemble the clutch disk and the clutch plate and put the bolts back in without tightening them. Now take the clutch alignment tool and push it thru the clutch disk and into the new pilot bearing. position it so the clutch disk is dead center in the clutch plate and then finish tightening the bolts Put a new throw out bearing on the clutch release lever and reinstall the transmission and transfer case. Reinstall the drive shafts and replace any gear oil that may have spilled out of the transmission or transfer case. Adjust the clutch pedal clearance to spec and you're done.

Mar 30, 2013 | 1996 Toyota RAV4

3 Answers

When I press the clutch in my 99 Rodeo, there is this horrible noise. What is the problem?


if the noise is only there when you push down the clutch, you need to replace the throw out bearing.

Apr 02, 2011 | Isuzu Rodeo Cars & Trucks

2 Answers

I have a 2000 Isuzu Rodeo in which the clutch pedal went to the floor & stayed there. Upon inspection, the clutch master cylinder was empty on fluid. I filled the reservoir & bleed the clutch...


It sounds as if you have 2 problems here.

The fact that the clutch pedal went to the floor and stayed there suggest a fault in the master cylinder. It may be that you need to overhaul the master cylinder.

Overhaul kits are available at less cost than a clutch master cylinder:
0results for isuzu rodeo clutch master cylinder overhaul kit

The grinding noise ... A grinding noise would be caused by either the gear not engaging properly because of the defective clutch.

Or, if it is more of a squealing noise - that may be the clutch release bearing at fault.

Are you absolutely sure that your entire clutch unit - pressure plate, driven plate and release bearing aren't worn?
116results for isuzu rodeo clutch

Mar 14, 2017 | 2000 Isuzu Rodeo

2 Answers

Has a noise at idle,like a noisy input bearing to the gearbox, if I push the clutch in the noise stops. but the noise is not there all the time, I can make it make the noise, if I depress the clutch a few...


Throwout bearing is going out so it means you would have to remove the transmission, and also could have a bad pilot bearing out and or a broken clutch spring so it would still need to remove the transmission to fix it and then If it where me I would do a clutch job on it.

Jan 24, 2010 | 2001 Isuzu Rodeo

1 Answer

Clutch assembly


Just put it back the same way you took it off. If you buy the right clutch kit (Sachs I think) it should come with a disc alignment tool. Remember to tighten the pressure plate bolts evenly all the way around the plate. And don't forget the pilot bushing or bearing.

Jan 03, 2009 | 2001 Isuzu Rodeo

1 Answer

Inner wheel bearing


The inner wheel bering is held in with a plate that is screwed in. no special tool is needed. You must remove the bearing housing from the brake disk. It took me 1.5 hours to do both sides.

Jul 02, 2008 | 1999 Isuzu Rodeo

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

181 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

76070 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...