Question about Mercedes-Benz ML320

Open Question

Hi, I get a "Start Error" message on Odometer of ML320 2002. Is this a Do It Yourself type of troubleshooting? Thanks

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where are all the ground wires located on a 2008 chevy cobalt?


It wouldn't be a ground problem If it were the whole instrument cluster would be dead . Checking the BCM an the IPC for DTC'S - diagnostic trouble codes is the proper way to diagnose this type problem . Not worrying about grounds .
Odometer
The vehicle odometer is calculated and stored electronically in the body control module (BCM) and is sent via the serial data circuit to the instrument panel cluster (IPC) for display. The BCM calculates and stores the mileage based on the vehicle speed serial data information from the PCM/ECM. The IPC displays the season odometer information from the BCM in the driver information center (DIC). The odometer will display error if the IPC detects an invalid odometer data from the BCM. After an invalid odometer data is received from the BCM, the IPC will display the last known odometer reading for 1.5 seconds before error is displayed in the DIC.
Speedometer
The instrument panel cluster (IPC) displays the vehicle speed based on serial data message from the body control module (BCM). The BCM receives vehicle speed data from the PCM/ECM via the serial data circuit. The speedometer will default to 0 km/h (0 mph) if:
• The PCM/ECM detects a malfunction in the vehicle speed sensor circuit.
• The BCM detects a loss of serial data communications with the PCM/ECM.
• The IPC detects a loss of serial data communications with the BCM.

Your best bet would be to take it to the dealer !

Apr 19, 2017 | 2008 Chevrolet Cobalt

1 Answer

I have a 2004 chevy Silverado 2500 HD and I got a odometer error message in my instrument cluster. Is this from the instrument recall from way back? Front left window switch works intermittently also.


Disconnecting the battery isn't going to change anything . You have a hard fault . The IPC calculates the mileage based on the vehicle speed signal circuit from the powertrain control module (PCM). The odometer will display 'error' if an internal IPC memory failure is detected. IPC- instrument panel cluster ! Is the odometer inoperative ?


Is the

Sep 01, 2015 | Cars & Trucks

1 Answer

Err message on odometer


what type of car are we talking about and what error message you get on the odometer please?

Sep 09, 2012 | Cars & Trucks

2 Answers

How do i get rid/ reset message xc90 "transmission service urgent" i have already taken to volvo dealer about six months ago. they could not pin point issue on diagnostic. Cheers


You first have to retrieve fault codes from your computer network then you have to diagnose the systems/circuits indicated by the fault codes to determine what the cause of the failure is, then you must repair the system/circuit at fault and then reset the computer system. If the dealer cannot do this, I don't know who can. Did they tell you what fault codes they were getting? If so, we can look up the troubleshooting charts for those codes as well as do a Technical Service Bulletin (TSB) search to see if this is a known problem with a known fix. Without the codes, your guess is as good as mine.

Sep 11, 2011 | 2004 Volvo XC90

1 Answer

1994 968 odometer stop working


Broken odometer gear... common problem..You can get this problem solved yourself, by taking the odometer out and replacing the gear.------- For exact procedure, click the link below:--- http://howtobyme.blogspot.com/2011/09/how-to-repair-odometer-on-porsche-968.html ---------- This will help.Thanks.Helpmech.

Sep 06, 2011 | 1995 Porsche 968

2 Answers

Service message comes on...need to clear out message thanks


Hi,

Do the following to clear out the service message 1. Press and hold trip odometer reset button
2. Turn ignition key to run position KPII (not the start position)
3. Wait 30 seconds or until service light begins blinking
4. Release Trip Odometer button
5. Turn ignition to off position

Thank you !!

Jun 16, 2010 | 2004 Volvo S40

1 Answer

I'm looking to purchase odometer km for 1993 Grand Cherokee Jeep


Hi Maria,
If your doing it yourself you need to locate all the screws around it and covers that are in the way and remove them as well. I would first wait until you get the KM Odometer and find where the holes are on that so you know what you have to remove to get to them. There are plugs and things to disconnect and reconnect to the new odometer but thats the easy part. The hard part is finding the screws and removing them some makes you need star bits so you might have to find a hardware store to buy them..Dont worry its really not that hard, just time consuming. Good Luck!
PS if your fast it may take about 2 hours!

Sep 15, 2009 | 1993 Jeep Grand Cherokee

2 Answers

My speedometer and odometer on my 98 ford explorer


the speedometer/odometer works on a cable that goes into the side of the transmission with one 10mm bolt holding it in. It sounds as if the cable has been broken,pulled loose, or siezed up. Its easy to check the end under the vehicle but its very complicated checking it inside the dashboard. If you are a do it yourself type of person, id look underneath and see if the connection under the vehicle is still connected. Look on left rear of the transmission for a cable that goes into it and is held with a "Y" bracket and a small bolt.The dashboard part is the type of job where u got to make sure you remember where each screw goes to get back together.

Jul 05, 2009 | 1998 Ford Explorer

1 Answer

Remove Oil maintenance required message on 2008 Toyota Highlander


This is the reset proceedure for a 2008 Highlander with a key-type ignition:

Turn the key ON, do not start the engine.

Look at the odometer, and verify that it displays "TRIP A". If it is on "ODO" or "Trip B", press the black stick next to the odometer to read "TRIP A".

Turn the key OFF.

Press in, and HOLD the black trip meter reset button, hold it IN.
DO not release it.

Turn the key ON, do not start the engine

Observe the Odometer display. You will see 5 dashes, then 4, then 3, then 2, then 1 dash, and finally, 5 zeros. Then, whatever number that was displayed on "TRIP A" will be re-displayed..

Now release the black trip meter reset stick.

This completes the reset procedure, and it will be back on in 5,000 miles, to remind you of you next oil change.

Hope this helps! Thanks for choosing FixYa!

Nov 15, 2008 | 2008 Toyota Highlander

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

206 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercedes-Benz Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

yadayada
yadayada

Level 3 Expert

76164 Answers

Michael Contreras
Michael Contreras

Level 2 Expert

166 Answers

Are you a Mercedes-Benz Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...