Question about 2003 Ford Explorer

Open Question

My 2003 Ford Explorer keyless entry pad stopped working is there a fuse is it wiring

Posted by on

Ad

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
bibleman01
  • 334 Answers

SOURCE: keyless key pad entry code

Ford cars and such will put a sticker on the hinge or back gate with the numbers on it. It will just be a white sticker with black numbers. A five digit code.

God Bless Greg

Posted on Nov 25, 2008

Ad
  • 65 Answers

SOURCE: Keyless Entry and Remote

I have had this problem take you drivers door put your key and un-lock from the out side with key (NO) then open the door push un-lock from the inside button and then set from you remote and it should set if not push un-lock then lock and then do the un-lock with the key. Let me know if that works. what my car did was locked from the inside and I had the problem were it would not work till I un-locked from the out side plus I had to go to radio shack and change the battery from the control.
Hope good happens.
Nikki2913

Posted on Dec 29, 2008

  • 1 Answer

SOURCE: Need factory code for keyless entry pad

To locate the original keypad code, open the passenger/rear door. Pull the on-body rubber weatherstrip out, around the rear side of the door closure. Fold the right/rear seatback down into the locked position to facilitate access to the right/rear seat belt anchor. Carefully pry the upper plastic panel that houses the height adjuster and seat belt anchor off the body taking care not to damage the panel. Now pry the lower panel outward just far enough to enable access to the Vehicle Security Module, where you'll see three electrical connectors plugged into it, coloured green, grey, and blue. On the module will be a series of digits on a label similar to 5L2T-15K602-EA. Beside those digits are five numbers. Those five numbers are the keyless entry keypad code.

Posted on Apr 30, 2009

  • 1 Answer

SOURCE: need keyless entry code for a 04 an 99 ford explorer

i have a2000 expedition w/ no keyless entry code. I see here you helped an explorer , can you help me locate mine, please?

Posted on Nov 23, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Horn has stopped working on my 2006 Ford Explorer. The fuse seems to be fine. What could be the problem?


I would suspect an underhood fuse, the steering wheel clock spring, or a wiring problem. It's cheap to triple check all the fuses. The other two will require some troubleshooting to figure out. Since the horn works with the keyless entry, the relay, the horn, and its control wiring seem to be ok.

Sep 20, 2014 | 2006 Ford Explorer

1 Answer

Ford explorer door lock


Mine did not have the keyless pad problem - but replaced switch after checking it with ohm meter - showed switch was electrically stuck in unlock.

Jan 31, 2014 | Cars & Trucks

1 Answer

Keyless Entry and Remote


The alarm box might be disconnected. I would locate it and trace the wires. Start under the dash behind steering wheel. It usually a little black box

Dec 24, 2011 | 1996 Ford Explorer

1 Answer

1995 FORD EXPLORER


Yes, Fords have PATS system, which is what controlls your keyless entry. It is the computer for your key fobs and keyless entry. You might have tripped itby accident, and your only solution is to take it to a dealership or someone who has Fords reprogrammimg computer to have it reflashed.

Sep 26, 2009 | 1996 Ford Explorer

1 Answer

Key Pad Entry does not work


does the key pad light when you press a button at night? If yes, the fuse is ok.
Do you have the plastic card with the permanent code in your owner manual packet? If yes, tryit.
report back.

Keyless Entry The keyless entry keypad is hardwired to the GEM. The GEM interprets the inputs from the keyless entry keypad and then controls the associated operation. The keyless entry keypad will be illuminated for five seconds when any button is pressed. Additionally, it will request the illuminated entry feature to turn the courtesy lamps on. If a lock all doors code is entered, the illumination will turn off, as well as request the illuminated entry feature to turn off the courtesy lamps. When pressed, the keyless entry keypad supplies the ground signal to the GEM or the GEM receives a signal from the keyless entry remote transmitter. Then the GEM outputs a ground signal to the appropriate lock or unlock relay which supplies the power to the actuator to lock or unlocks all doors, including the luggage compartment. The keyless entry remote transmitter also unlocks the liftgate or activates the panic alarm by sending a signal to the GEM.
--------------------------------------------------------------- Visual Inspection Chart Mechanical Electrical
  • Keyless entry keypad
  • Keyless entry remote transmitter
  • Central junction box (CJB) Fuse F222 (20A)
  • Circuitry
  • Generic electronic module (GEM)
------------------------------------------------------------------------
  • No communication with generic electronic module (GEM)
  • Generic electronic module.
  • Circuitry.
  • REFER to Section 419-10 .
------------------------------------------------------------------------------------

Mar 08, 2009 | 2003 Ford Taurus

1 Answer

2001 Mercury Sable Keyless Entry-Fuse


check this fuse first. I believe it's #30. Check with chart on fuse panel cover or in your owner manual.eb303fa.gif

Jan 10, 2009 | 2001 Mercury Sable

1 Answer

1993 ford explorer


the keyless entry pad may be an add on from the dealer which was just stuck on therefore comtains a battery need to remove the door panel and check for wires from pad

Sep 14, 2008 | 1993 Ford Explorer Limited

1 Answer

Keyless key pad entry code


Ford cars and such will put a sticker on the hinge or back gate with the numbers on it. It will just be a white sticker with black numbers. A five digit code.

God Bless Greg

Jul 16, 2008 | 2003 Ford Windstar

2 Answers

2002 Ford Focus wagon remote keyless entry system


Driver door module is where to look also a broken or corroded wire and if you use your key to punch in the door code then the key pad has a hole in it or it just went bad it's not the remote control also check the master door lock switch for corrosion at the pins and the plugs same with the driver door module

Aug 15, 2017 | 2002 Ford SVT Focus

Not finding what you are looking for?
2003 Ford Explorer Logo

Related Topics:

217 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

fordexpert

Level 3 Expert

5546 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...