Question about 1999 Chrysler Sebring

Open Question

Oldcrank sensor stuck & broke in half how do i get it out

Posted by on


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Wheel speed sensor broke off in the knuckle how to remove

Wheel speed sensor removal? Stuck on tight! - North American Motoring
Jun 29, 2010 - I've read here that having my DSC/ABS/Tire lights going off and on .... of the sensor before putting it back in the hole on the steering knuckle,

Chilton's Auto Repair Manual, 1993-1997
Chilton Book Company - 1996 - ā€ˇTechnology & Engineering
Top off the master cylinder reservoir to the proper level with DOT 3 type brake fluid only. ... Remove the front wheel(s) of the wheel speed sensor(s) requiring removal. 4.Remove the speed sensor cable routing bracket from the steering knuckle. ...Carefully inspect the tone wheel for broken or missing teeth which can cause .

Nov 23, 2015 | Cars & Trucks

1 Answer

How do i remove broken front wheel sensor stuck in the knuckle 3006 chrysler 300c awd

Usually you have to use a drill & carefully extract broken sensor

Nov 23, 2015 | Chrysler Cars & Trucks

1 Answer

1980 Cadillac Biarritz 368 fuel injection

How about timing chain being worn & gears stripped ?

Put a timing light on it, then put the pick up on a wire
half way thru the firing order & see if they timing is
the same.

Feb 17, 2013 | 1980 Cadillac Eldorado

1 Answer

Lower ball joint broke and half shaft pulled out tansaxle

You have no money to get it fixed

You have no money for parts ,no tools,
& no experience

So all you need to do is get it up to the house
& out of the way for now

Borrow a floor jack & put under the bottom
control arm & get about 5 people to push it up hill

Feb 10, 2013 | 1994 Honda Accord

2 Answers

Code p0170

What year vehicle ? mass air flow or speed density fuel control . Do you have a scan tool that can view sensor data . What are the fuel trims ( short & long term ) showing ? PCM problem ? O2 sensors stuck lean , adding propane , do the O2 sensors go rich ?

Jan 10, 2018 | Chrysler Town & Country Cars & Trucks

1 Answer

Half of key broke off inside trunk lock

you need to have the trunk open and the lock unlocked first then you can get the barrel out of the lock and remove the broken part of the key,,,so dont lock the trunk till you get it fixed,,,

Jun 20, 2010 | 1998 Toyota Camry

1 Answer

My gas pedel gets stuck half way down some times

The throttle position sensor is most likely bad or it just may be the throttle cable but I think it is the Throttle position sensor it is located near the throttle valve follow the throttle cable to the end this is where the throttle valve is and the Throttle position sensor is located near the throttle valve on the opposite side it will have a plug going to it and it is held on with two torx head screws purchase the tools and replace.

Nov 03, 2009 | 1998 Buick Century

1 Answer

Schrader valve stuck

try a core tool for tires

Jul 22, 2009 | 1992 Acura Integra Hatchback

2 Answers

Broke crankshaft position sensor

go to parts store and buy a easy out set.. this tool will back out the broken half for you...keith...

Mar 14, 2009 | 1997 Dodge Stratus

1 Answer

Overtightened the coolent temperature sensor and it broke.

Take the piece that broke off to any auto parts store and they will have an extractor that will remove the other piece. good luck.

Feb 01, 2009 | 1997 Honda Civic

Not finding what you are looking for?
1999 Chrysler Sebring Logo

Related Topics:

36 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts


Level 3 Expert

82313 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22382 Answers


Level 3 Expert

814 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides