Question about 1990 Oldsmobile Cutlass Ciera

2 Answers

1990 cutlass ciera w/3300 v6, won't start, fuel presure is 45psi, has good spark, has new crank sensor. still won't start, what next.

Posted by on

Ad

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Oldsmobile Master
  • 6,826 Answers

If it has spark, the crank sensor is working. If the fuel pressure is 45psi, that's good.

Are the injectors pulsing controlled by the computer?

Posted on Aug 01, 2010

Ad
  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Check for shorted out fuel injectors, OHM each injector I believe they should have more than 2 ohms less than that they will short out and not allow car to start.

Posted on Feb 28, 2012

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1991 Cutlass ceirra 3300 ,runs fine for short time. starts running rough,then dies/will not start again.changed fuel filter, then tested fuel pump.fuel pressure is good.what next ?


Check for spark when it won't start. If you have spark, might be your fuel pump relay, maybe the map sensor. If no spark, check another or all plug wires. If ignition isn't working, it could be Crankshaft Position sensor, Camshaft position sensor (or pick-up coil), ignition control module, coils, pcm, or the wiring associated with them. PCM determines spark timing after inputs from crank and can sensors, and sends ground signal to ignition module, cutting primary voltage to coils, initiating spark or high voltage from coil to sparkplug. All these parts have to be working right for ignition. All can be tested too. You'd need a digital volt ohm meter (DVOM) and a repair manual for your car with the test procedures. That Mitchell alldata-diy site has a special on subscriptions, pretty reasonable for a 1 month subscription, and excellent info and troubleshooting flow charts, wiring diagrams, etc.

Dec 26, 2012 | 1990 Oldsmobile Cutlass Ciera

1 Answer

I have a 1989 cutlass ciera 3.3L that cranks but won't stay running. I had a diagnostic test but no codes came back. I have checked the fuel pump, fuel injectors, and fuel pressure which are all good....


You need to figure out what you are missing. What is the fuel pressure at the rail when you are cranking the engine? It needs to be above 40PSI. If you have sufficient fuel pressure you need to check for spark at the plugs while cranking. If you verify you have sufficient fuel and spark then you need to look to timing and compression. These are the four things an engine need to run. Fuel, spark, compression, and timing.

Dec 19, 2017 | 1989 Oldsmobile Cutlass Ciera

1 Answer

I have 1995 olds cutlass cierra s with 3300 v6, dies when warm, rest for about 15 min and starts up till warm. replaced ignition module, o2 sensor, fuel filter, fuel pump, air filter. i've worn out my...


the most common problem next is the crank sensor. use a heat light to warm up the sensor to see if it is that. by using a heat light you can narrow down what part has the temperature glitch. Don't forget to try the engine computer.

Jun 06, 2011 | 1995 Oldsmobile Cutlass Ciera

2 Answers

My 92 cutlass supreme wont stay started whats wrong with it


Most of the time when it starts for 1-5 seconds then dies, its a failing of the antitheft system. Read about it thru this link. Some possible solutions too. http://vatspasslockpasskeysecurityhelp.yolasite.com/

May 20, 2011 | 1992 Oldsmobile Cutlass Supreme

1 Answer

1989 oldsmobile ciera no spark unit cranks fine good fuel presure


most common cause of no spark is the ignition module located under the coil

Jan 09, 2010 | 1989 Oldsmobile Cutlass Ciera

1 Answer

In which area of the engine would I be able to find crank sensor


CRANKSHAFT POSITION SENSOR

Fig. 8 Ignition Coil Module Assy 2.5L/4-151 42188531 The Crankshaft Position Sensor is mounted remotely on the bottom side of the ignition module.

RH Side Of Engine. 42277335

Front RH Side Of Engine

Applicable to: Cutlass Ciera & Cutlass Cruiser w/V6-231/3.3L

Dec 11, 2009 | 1991 Oldsmobile Cutlass Ciera

Not finding what you are looking for?
1990 Oldsmobile Cutlass Ciera Logo

591 people viewed this question

Ask a Question

Usually answered in minutes!

Top Oldsmobile Experts

Marvin
Marvin

Level 3 Expert

81423 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22359 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8841 Answers

Are you an Oldsmobile Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...