Question about 1994 Chevrolet S-10 Blazer

2 Answers

My 94 chevy s10 blazer is leaking power steering fluid pretty bad from the lines or pump itself. How many lines are there for the power steering pump.

Posted by on

Ad

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 5 Answers

Sometimes the seal under the pitman arm that works the tierods gotta pull the pitman arm and replace the seal in sterring colum

Posted on Aug 10, 2010

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Chevrolet Master
  • 22,156 Answers

The main one is the feed which is pressurised and the main cause is the flexible rubber pipe ,they perish and go porous ,take this pipe off and have the rubber part replaced in a hydraulic type place that does industrial type work ,might cost 20 euros if that

Posted on Aug 01, 2010

Ad

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: 94 chevy s10 blazer power windows not working

I had the same problem - driver side fine, passenger side front not working/slow or the back seat. You need to replace the window motor on the passenger side. Yes, there are two motors. It's pretty simple if you are handy with some tools. The hardest part is getting the 4 mounts that hold the window motor to the door off. The are factory riveted to the door, so I had to grind the outsides off and tap them out. Just watch the spring lever that holds the window bar for going up and down. I didn't pay attention and it snapped back - nearly broke my thumb.

Dani-Lynn

Posted on Oct 05, 2009

  • 3741 Answers

SOURCE: Where is the turn signal relay on a chevy s10

On 95-97 and 1998, both the turn signal and hazard flashers are located behind the lower dashboard trim just to the left of the cigarette lighter. You can not get to it without taking apart the trim (stupid design). Or you have to drill a 2" diameter hole in the trim with a velcro cover so you would never have to do it again1999 and later it is under the glove compartment
to disassemble it without drilling
It's behind the panel to the left of the cigarrette lighter. You need a Torx 25 screwdriver and another screwdriver for those hex shaped screws, forgot the size. First unscrew the 2 Torx 25 screws beneath the steering wheel. Then unscrew the rest of those Hex screws on the bottom. The panels overlap, so be prepared for a lot of unscrewing. You do need to unscrew the middle black panel on the bottom, right beneath the cig lighter. It's held by two Hex shaped screws, one on each side and are hard to unscrew. Also you need to remove your spare change sliding tray to unscrew the last hex looking screw. Once you pop your panel off, the turn signal flasher is the right one. The Hazard flasher is the left one. You can find a replacement part at Autozone, and DON'T get the $184 Flasher switch, all you need is the signal flasher. It's shaped like a cylinder with TWO prongs on it.

Posted on Nov 03, 2009

duane_wong
  • 6826 Answers

SOURCE: repair power steering for 1994

Power Steering Pump Removal & Installation 2.2L Engine To Remove:

  1. Remove the upper cooling fan shroud.
  2. Position a fluid catch pan under the power steering pump.
  3. Disconnect the feed and return hoses from the power steering pump, then drain the excess fluid into the catch pan. NOTE: On models equipped with a remote fluid reservoir, disconnect and plug the hose(s) in order to prevent system contamination or excessive fluid loss.
  4. Remove the drive belt from the pulley.
  5. Install a puller tool such as J-25034, or equivalent onto the power steering pump pulley. While holding the pilot bolt, turn the tool nut counterclockwise in order to press the drive pulley from the pump. NOTE: When installing the puller tool onto the power steering pump pulley, be sure that the pilot bolt bottoms in the pump shaft by turning the head of the pilot bolt.
    Installing the pilot bolt 85388111.gif

    Removing the power steering pump pulley 85388113.gif

    Installing the power steering pump pulley 85388114.gif

  6. Unplug the electrical connection from the A/C compressor, unfasten the compressor mounting bolts and set the compressor to one side without disconnecting the lines.
  7. Remove the front mounting bolts and the rear bracket nuts from the studs on the engine.
  8. Remove the rear brace mounting bolt.
  9. Remove the power steering pump from the vehicle.
To Install:
  1. Position the pump to the vehicle and secure using the front retaining bolts to 22 ft. lbs. (30 Nm).
  2. Install the rear bracket bolt and nuts. Tighten the retainers to 22 ft. lbs. (30 Nm) on 1994 - 97 models and 37 ft. lbs. (50 Nm) on 1998 and later models.
  3. Install the A/C compressor.
  4. Use a pulley installer such as J-25033 or equivalent to press the drive pulley onto the power steering pump. While holding the pilot bolt, turn the tool nut clockwise in order to press the drive pulley onto the pump. Check that the pulley is flush within 0.010 in. (0.25mm) of the shaft end. NOTE: When positioning the installer tool onto the power steering pump pulley, be sure that the pilot bolt bottoms in the pump shaft by turning the head of the pilot bolt.
  5. Properly install the drive belt.
  6. Remove the caps, then connect the feed and return hoses to the pump.
  7. Properly refill and bleed the power steering system.
  8. Test drive the vehicle.
4.3L Engine To Remove:
  1. Remove the upper cooling fan shroud.
  2. Remove the drive belt.
  3. Remove the fan and clutch from the water pump.
  4. Install a puller tool such as J-25034, or equivalent onto the power steering pump pulley. While holding the pilot bolt, turn the tool nut counterclockwise in order to press the drive pulley from the pump.
  5. Safely raise and support the vehicle.
  6. Remove the shield from the steering linkage.
  7. Position a fluid catch pan under the power steering pump.
  8. Disconnect the return hose from the power steering pump, then drain the excess fluid into the catch pan.
  9. Safely lower the vehicle.
  10. Disconnect the pressure hose from the pump and cap the open line.
  11. Remove the filler neck tube.
  12. Remove the power steering pump mounting nuts and bolts.
  13. Remove the power steering pump from the vehicle.
NOTE: When installing the puller tool onto the power steering pump pulley, be sure that the pilot bolt bottoms in the pump shaft by turning the head of the pilot bolt.
Installing the pilot bolt 85388111.gif

Removing the power steering pump pulley 85388113.gif

Installing the power steering pump pulley 85388114.gif

To Install:
  1. Position the pump to the vehicle.
    • Tighten the front retaining bolts to 37 ft. lbs. (50 Nm) and the nuts to 31 ft. lbs. (41 Nm).
  2. Install the filler neck tube.
    • Tighten the bolt to 15 ft. lbs. (20 Nm).
  3. Connect the pressure hose to the pump.
  4. Safely raise and support the vehicle.
  5. Connect the return hose to the vehicle.
  6. Install the shield on the steering linkage and lower the vehicle.
  7. Use a pulley installer such as J-25033 or equivalent to press the drive pulley onto the power steering pump. While holding the pilot bolt, turn the tool nut clockwise in order to press the drive pulley onto the pump. Check that the pulley is flush within 0.010 in. (0.25mm) of the shaft end. NOTE: When positioning the installer tool onto the power steering pump pulley, be sure that the pilot bolt bottoms in the pump shaft by turning the head of the pilot bolt.
  8. Install the fan and clutch on the water pump.
  9. Properly install the drive belt. NOTE: Be sure to secure any hoses which may get in the way or rub other components.
  10. Install the upper fan shroud.
  11. Properly refill and bleed the power steering system.
  12. Test drive the vehicle.
prev.gif next.gif

Posted on Nov 05, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2002 chevy blazer steering wheel squeaks bad while turning


It the "squeaking coming from the steering wheel itself, or from the vehicle when the wheel is being turned? If it is the wheel itself, the only ting you can do to remedy that is to disassemble the steering column to lubricate the insides. If it is the vehicle that squeaks/squeals when the wheel is turned, then it is probably one of three things. From most likely to least likely they are:

1. Worn out/glazed serpentine (drive) belt
2. Defective belt tensioner
3. Defective power steering pump (or low fluid in reservoir).

Jan 06, 2016 | 2002 Chevrolet Blazer

1 Answer

Was driving 2004 trail blazer and the power steering went out was hard trying to turn wheel pulled over and it was leaking on the driver side it wasnt making no noise it just happen so what should i do...


Sounds like you've lost hydrolic pressure. Did you check the 2 hoses connecting to the power steering pump? I take it, you lost power steering fluid also right? If it was leaking badly, it was the high pressure line that blew, if not, it was the return line. You can have a hose made for you for pretty cheap to replace the hose.

Dec 22, 2010 | 2004 Chevrolet TrailBlazer

1 Answer

Power steering fluid leaking pretty good on 2005 chevy impala. not from pressure line ithink. any clues


The power steering pump is belt driven. It is on the engine where you put fluid in. There are two lines that run from the power steering pump to the power steering rack on the firewall. The fluid can leak from the pump, either of the lines or the rack itself. If you are handy you may be able to repair the problem by replacing the bad part. Wear safety glasses when looking for the leak and do not touch the fluid leak when the engine is running. The pressure is high enough to hurt you. If you ignore the problem you will eventually loose the power assist and may be unable to steer the car. Fix it now!








One line is high pressure and the other is a return line. Check them with the engine off and when you think you've found the leak staret the car and look for the leak. If it sprays like a water hose DO NOT TOUCH THE LEAK. The pressure is high enough to cause serious injury.

Mar 19, 2010 | 2005 Chevrolet Impala

2 Answers

My 2006 chevy impala has a massive power steering fluid leak, so my power steering goes out. This problem is solved when there is fluid in the system. Do i need to replace the entire power steering pump?...


you just need to check your steering pipes and hoses for any leaks. just replace them if a leak is found. if your reservoir itself has a leak, then your only best bet is to replace the whole ting ..

Dec 28, 2009 | Chevrolet Chevy Cars & Trucks

2 Answers

I have a 2003 chevy blazerthat has power steering problem no leak


There is a "pressure regulator" located in the pump just behind the high pressure line that directs high pressure fluid to the steering rack when you turn the steering wheel. It sounds like the regulator valve is sticking and not sending the high pressure fluid to the steering rack when you turn the wheel.
You can remove the pump and clean the valve, reinstall the pump and flush the steering system with fresh fluid or replace the pump and flush the system with new fluid.
Good luck.

Oct 23, 2009 | 1996 Chevrolet Blazer

4 Answers

Power steering dont work to left or right


To find out witch it is,pump or rack and pinion,break loose the presure line on the power steering pump with a wench.Start the car and turn the steering wheel back and forth,you may need to loosen the nut on the power steering hose two or three turns to get the fluid to shoot out.It should come out pretty forceful.If it doesn`t,then replace the pump.If it does come out really powerful,replace the rack and pinion.

Aug 10, 2009 | 1998 Pontiac Bonneville

1 Answer

Turn signal relay switch, 94 s10 chevy blazer


It's behind the dash panel just below the steering column. There are two relays for the fuel pump back there. Chande them both out.

May 27, 2009 | 1994 Chevrolet S-10 Blazer

1 Answer

1999 Chevy S10 Blazer 4x4. Replacing rear pad's,& Bleeding Breaks


have one person in the blazer pumping the brake pedal and then hold to the floor, crack the bleeder then tighten, release pedal, repeat till all air is out one side at a time, if this does not work then your ABS unit is bad witch if u follow your lines from your master cylinder u will find a black box with a motor on it, or the master cylinder itself is bad, it also can cause u to have no pedal, replace the master cylinder first, most likely cheaper.

Mar 11, 2009 | 1997 Chevrolet S-10 Pickup

2 Answers

Power steering


its on the pump. driver side of the pully system.

Jul 01, 2008 | 1993 Chevrolet S-10 Blazer

Not finding what you are looking for?
1994 Chevrolet S-10 Blazer Logo

576 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8270 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...