Question about 2006 Ford F-250 Super Duty

1 Answer

Horn not working, replaced failed fuse, no response

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Ford Master
  • 22,246 Answers

Test for a current to teh horn ,if current to horn then assistant holds it on ,squirt with proper oil can and engine oil around the vibrating diaphragm and tap with a small hammer,once it start to work dont let go hold horn on for a least a whole minute .then it should work for quite a while especially if you oil it regular

Posted on Aug 01, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I Repair horn 2000 mustang


You do not repair a horn--you replace it,
after you test it & it is fails to work

Was the fuse blown--if not-- why replace it?

Nov 01, 2014 | 2000 Ford Mustang

1 Answer

Horn is ok but not working


Just curious - how can the horn be OK if it doesn't work?
Of course, horns do fail, their wiring and/or fuse can fail and the switching mechanism can fail.
Put your DC meter on the horn terminals and attempt to blow the horn - if you measure 12vdc, replace the horn. If no 12vdc, you have either a failed horn switch or a wiring fault.

Mar 23, 2014 | 2005 Toyota Corolla

1 Answer

Miata mx5 horn does not work


The fuse is the most likely problem. The fuse for the horn is the same as for the stop lights. 15 amp fuse located in the fuse box under the dash on the drivers side. If it's blown and it fails again once you replace it, the horn is bad.

Aug 25, 2013 | 1990 Mazda MX-5

1 Answer

Replace horn 2002 highlander


Mine went twice in 600,000 km with the characteristic last gasp sound. Check that your fuse for the horn is ok (in plastic covered fuse block under the hood). If it's blown, replacing it may not work as failed horns can act as a short. Then, I would suggest that you go to a dealer parts department to ask about their OEM horns for your Highlander and to get them to print out the horn placement diagram for the vehicle. You'll see that you have 2 (or even 3) horns. I seem to recall that Toyota wanted over $100 for their OEM horns each. In any case, it was too much. I went to an auto parts store (Napa?) and picked up an inexpensive dual tone universal horn. Under the hood, the collision sensors are close by so best to disconnect the battery to be safe. Now, I replaced the horn on the drivers side -- it's tight to get in there, but you can do it. Connect up the single horn wire (the horn's negative is connected through the mounting hardware). I also disconnected and insulated the wire to the horn in front of the rad (old failed horns can can act as a short). Assuming that your fuse is good, reconnect the battery (and set up your clock and radio stations) and, hopefully, you'll be good to go.

Feb 23, 2013 | 2002 Toyota Highlander

2 Answers

My 2005 Pontiac Sunfire horn stopped working. I've tried replacing the fuse, but that's not the problem. Any ideas?


Hello: It could be a failed horn. the best way to check is to get a test light and connect one end to the green wire at the horn connection and the other end to a good ground, have helper press horn. if test light lights up the horn has failed. also you might check the fuse box under the hood and see if there is a horn relay. if there is a horn relay then look to see if there another relay like it. if there is one swap the relays and see if the horn works.

Jan 26, 2011 | Pontiac Sunfire Cars & Trucks

1 Answer

Horn does not work


THE HORN MAY BE BAD. HORN FAIL FROM AGE & LONG PERIODS OF NON USE. TRY PUTTING BATTERY POWER RIGHT TO THE HORN. IF NO SOUND OR VERY POOR RESPONSE, GET A NEW HORN. IF IT SOUNDS LIKE A HORN, CHECK THE HORN FUSE WITH A TESTER, " THERE SHOULD BE POWER ON BOTH SIDES OF THE FUSE. IF THE FUSE IS GOOD, PULL THE STEERING WHEEL, THERE MAY BE A WORN BRASS CONTACT STICKING UP. PUT A WIRE FROM THAT CONTACT TO SOME METAL UNDER THE DASH, IF THE HORN WORKS YOU WILL HAVE TO WORK ON THAT CONTACT OR MAYBE THE HORN BUTTON ON THE STEERING WHEEL

Nov 28, 2010 | 1988 Toyota Pickup

3 Answers

The horn on my 2001 jeep cherokee sport does not work. It makes a clicking noise under the dash when I use it.


if its clicking the relay is working check power from relay to horn but your horn is probably full of stuff etc give your horn a tap it will probably work

Jul 24, 2010 | 2001 Jeep Grand Cherokee

1 Answer

I need to get a fuse box layout for 1999 Saturn SL2. The horn is not working in my sons car and we would like to determine whether or not it is the fuse. We can't tell which fuse is for the horn because...


The saturn horns ARE notorious for failing, you may have to replace the horn because it has a built in horn relay that is the cause of the failure. YOU WILL KEEP BLOWING FUSES if the horn is not working because it's grounding out through the bad relay that is built into the horn. DON'T go with a loud or aftermarket horn if you don't know how to wire it safely or you will fry the clock spring in the steering wheel, just stick with the stock horn and you will be fine.

Mar 29, 2010 | Saturn SL2 Cars & Trucks

1 Answer

2000 Sentra - horn problem


The horn fuse had power to it and the fuse was ok. The problem was a wire - from the fuse location - had a break.

Oct 08, 2009 | 2000 Nissan Sentra

Not finding what you are looking for?
2006 Ford F-250 Super Duty Logo

Related Topics:

75 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

fordexpert

Level 3 Expert

5546 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...