Question about 2007 Toyota Tacoma
2007 toyota tacoma 4x4 temp and compass stopped working, no led nothing
The overhead console is quite prone to internal failure. Dim, intermittent, or dead displays are a common symptom of an internal failure. We offer a reasonable repair service with a lifetime guarantee. Check it out: www.autoclockrepair.com
Posted on Aug 18, 2010
'05 - '09 Tacoma temp and compass gauge displays commonly 'burn out' due to component failure on the circuit board; this is not due to a fuse, and the dealership charges $200 or more for the new part.
However, we permanently fix the problem using all new components and a lead wire underlayment as a heatsink. See our site for more info: http://www.toyotatacomacompassrepair.com
Thanks and good luck...silicongeek
Posted on Dec 19, 2010
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
Here's a link to this great service
Posted on Jan 02, 2017
SOURCE: 2005 Toyota Tacoma 4x4
I found the solution to this on one of the Toyota Tacoma forums, there is a service bulletin out for this particular problem, a replacement circuit board to do a factory repair is 800 to 1000 dollars depending on which Toyota dealer you want to throw your money at.
The way you get the overhead console apart is to open up the sunglass holder and remove the lone screw in the middle. Some say it is a Torx head screw, mine was a phillips which I promplty dropped into the far reaches of the passenger seat and had to retrieve ith with a magnet.
Once thats done, grab the front of the console between it and the headliner. I tried a nice steady pull but I think it would be better to use a quick **** to dislodge the clips. It is a little scary because I'm sure the console is high-dollar too. Pull straight down to keep from breaking off the plastic posts on the console. The bad part for me was that when it all came apart, the metal clips came off and one is now lost in my headliner somewhere. I went to the local Toyota parts department, and yea they can get me a replacement, I have to order a minimum of ten at around $8.00, the other thing is, Helena MT.is a geographical oddity, two weeks away from anywhere. Whatever happened to customer service? I have a theory.
So, once you get the console down, disconnect the two connectors, one for the temp and one for the map lights. The console comes down, you can slide the connector off the console for the map light, and using a T-10 screwdriver, remove the three screws holding the circuit board to the console. Remove the lens from the circuit board and you should be able to see the 510 resistors. The one that came loose on mine was pretty easily seen. To verify this is the problem with the nonfunctioning indicator, press on the resistor with the unit plugged back in the truck, it should light up. Keep in mind, while you are admiring your troubleshooting expertise while holding the resistor down, those bad boys heat up pretty quickly.
I was able to solder mine back on very carefully using my weller gas powered soldering iron and some .032 diameter solder, use a clean, newly-tinned tip and it should be fine. Be careful not to heat the board too much.
Installation is the reverse of removal, unless you lose a clip, good luck finding those.
Posted on Aug 31, 2009
Hello, and welcome to FixYa. Please allow me to assist you.
You have an unfortunatly common problem, and Toyota has addressed this issue by redesigning the compass/temp module. They have issued a technical service bulletin that adresses this problem.
The new part number is 83290-04030. This part can be purchased at your local Toyota dealer's parts department. If you have an extended service contract; this part may be a covered item.
Thanks for choosing FixYa for assistance today.
Posted on May 20, 2010
Are your cruise control, dome, and tail lights also out? If so then it
is a fuse. If not then the control unit has gone bad internally. You may
be able to get it fixed under your warranty.
If it is not covered by your warranty, check out
www.autoclockrepair.com. We offer a very reasonable repair solution.
Posted on Jul 03, 2010
Tips for a great answer:
Apr 11, 2011 | 2007 Toyota Tacoma
Dec 18, 2010 | 2007 Toyota Tacoma
Nov 06, 2010 | 2005 Toyota Tacoma
Jul 20, 2010 | 2005 Toyota Tacoma
May 11, 2010 | 2006 Toyota Tacoma
Feb 24, 2010 | 2007 Toyota Tacoma
Jan 14, 2010 | 2006 Toyota Tacoma
Jul 28, 2009 | 2005 Toyota Tacoma
Mar 07, 2015 | 2007 Toyota Tacoma
1,057 people viewed this question
Usually answered in minutes!