Question about 2000 Chrysler Concorde

1 Answer

All the brakes lights are not working; this happened at the same time. What can the problem be?

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 52 Answers

Replace the fuse of brake light located in fuse box under the dash board

Posted on Aug 01, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

VDC light won't go off. This is the first time this has happened. It is really cold out. Would that have an effect.


The first time this happenned to me I wondered as well. It also happenned during a coold snap. Turned out the VDC light on is a warning for the brake system when the pads need to be replaced. Had the brakes done and the light went off. Happenned several times. -2004 G35X

Jan 23, 2013 | 2005 Infiniti G35

1 Answer

Changed back brake pads on 2004 tahoe , now the brake light and stabilty light is staying on . why? and what do i need to do?


If you have disc brakes on back, did you open the bleeder valve to compress the caliper piston? If not and you pushed the fluid back into the system, you could have blown the seals in the antilock brake system, This doesn't happen all the time, but does happen. If you did the brakes will still work, just not the ABS.

May 22, 2011 | 2004 Chevrolet Tahoe

2 Answers

2007 Nissan Versa brake lights not working................. fuse is ok. All other lights are working


Did you check the bulbs ? If they are Ok,then check you brake light switch which is under your brake pedal. Good luck

Jan 09, 2011 | 2007 Nissan Versa 1.8 Sl Hatchback

1 Answer

Abs warning light comes on with brake light, but have strong brakes


The ABS light is telling you that the anti locking part of your brakes is not working, the brakes will still function like non ABS brakes. Check all of the brakes to make sure the electrical connection is still in place, every time I've had this happen one had came up plugged.

Jun 27, 2009 | 1998 Buick Century

1 Answer

All dash gauge related


CHECK YOUR BRAKE FLUID LEVEL, IF ITS LOW THE LIGHT CAN GO ON AND OFF OVER BUMPS. YOU MAY ALSO NEED BRAKES. THE FLUID IS IN THE CALIPERS.

THE FUEL GAGE PROBLEM IS MOST LIKELY THE FUEL LEVEL SENSOR.

Jun 16, 2009 | 2001 Chevrolet Silverado 1500

1 Answer

Abs brake light stays on


There is no ABS brake light. Take the vehicle back to whatever service center/garage did the brake work and tell them to fix it.

Apr 05, 2009 | 2003 Hyundai Santa Fe

1 Answer

Brake lights work intermittently


It sounds like a wiring fault - an earthing problem. Have a look around the lights/inside the lights themselves.. rear and front lights, brake lights, etc ...check the wires for corrosion/splitting. In particular check any black earth leads where they attach to an earthing point.

Mar 26, 2017 | 1997 Chevrolet Lumina

1 Answer

Rear brake lights will not go out


look under under dash board behind and near top of break pedal shaft there is a brake switch, might be stuck in the in position.

Jan 23, 2009 | 2003 Mercury Mountaineer

1 Answer

Brake lights dont work


What happens when you run a jumper wire from another fuse cavity, directly to brake switch?

Oct 15, 2008 | 1991 Dodge Dakota

1 Answer

2002 YUKON XL Denali no brake lights or cruise


FROM LUSTY KID:

Check your bulbs first, I have lost both headlights on my ford at once on account of the bulbs burning out at the same time. Same thing probably happen, you have one filament out. The lights can work, but if the filament for brake is burnt, you don't see brake lights.

As for the cruise control. Check fuse box first. If OK check vacuum hose to actuator in engine compartment for starters.
Advise:

Oct 12, 2008 | 2002 GMC Yukon XL

Not finding what you are looking for?
2000 Chrysler Concorde Logo

113 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

Marvin
Marvin

Level 3 Expert

82331 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22382 Answers

chargerhp
chargerhp

Level 3 Expert

814 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...