Question about 1994 Eagle Talon

1 Answer

A new clutch, slave cylinder, and clutch master cylinder were all installed but when i push the clutch pedal down it still doesnt engage the clutch all the way, it acts like it is getting a little pressure but not enough to engage it all the way, the adjusting rod on the master cylinder is out all the way, i dont know what to do now?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Eagle Master
  • 11,800 Answers

Have you checked that the slave cylinder is attached firmly where it's supposed to be? Have you refilled the bowl of the master cylinder with braking fluid? And finally have you bled the circuit thoroughly after that?

Posted on Aug 01, 2010

  • 1 more comment 
  • atwan1991 Aug 01, 2010

    everything is attached firmly, all reservoirs were filled, systems were bled and then the reservoirs were filled again

  • atwan1991 Aug 01, 2010

    the system was bled three times and then brought to a technician and he said it was already bled,

    neither the technician nor i know what is wrong now

  • Azrael SRL Aug 01, 2010

    In that case one of the new cylinders is defective - it's internally leaking, most likely it's the master cylinder. The only way to know precisely is to replace the old master one back in the car and test again - if it's the same then it's the slave one, if it's fixed it's the master one. 

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Need a clutch pedal diagram for a 1999 s10 2.2 4cyl manual trans


Sorry no diagram. But here is how it works. In the start position(Power) the wire goes to the start fuse, from the fuse it goes to the clutch pedal switch. Push the pedal and it goes to the starter relay. On the other end is ground. If it is good it pulls the relay closed. On the closed end is battery power to the starter.

Mar 09, 2016 | 1999 Chevrolet Silverado 1500

1 Answer

I have a 2000 mazda 323 with a manual transmission. i have already change the clutch kit but the gear is still hard to shift


Check the hydraulic clutch operation. This is a clutch master cylinder with a reservoir on the firewall, and a clutch slave cylinder down on the bell housing of the transmission, with a steel tube running from the master to the slave cylinder. When clutch pedal is depressed, hydraulic fluid (brake fluid) is forced from the master to the slave. The slave cylinder should push out a little plunger that contacts the clutch fork lever-pushing it forward to engage the clutch.
Add brake fluid to the reservoir if needed. Watch the plunger on the slave cylinder: if it moves little, or not enough, try bleeding the slave from the bleeder valve. They are bled just like brakes. If bleeding doesn't help, your clutch master or the slave may need replacing. The master cylinder, like a brake master, has internal seals that hold hydraulic pressure, so force can be applied to the plunger on the slave cylinder.

Dec 09, 2013 | Mazda 323 Cars & Trucks

1 Answer

Clutch not engaging


Well, it would shift easily with engine off, because the transmission input shaft is not turning. Engine running and clutch engaging good, the input shaft would again be stationary and allow smooth shifting.
What you have to determine is if the clutch disc or pressure plate is bad (a new clutch is needed), or if the pedal hydraulic system has a malfunction. When you push the pedal down, a rod from the top of pedal pushes into the clutch master cylinder bolted to the firewall under the hood. This cylinder has a reservoir filled with brake fluid. When the rod forces fluid from the clutch master down a steel line and into the clutch slave cylinder down on the transmission bell housing, the hydraulic pressure forces a plunger from the slave cylinder to extend and push the clutch fork lever a small amount, enough to force the clutch release bearing (aka throw-out bearing) against the pressure plate. This relieves pressure on the clutch disc and input shaft becomes stationary for easy shifting.

Jul 26, 2013 | 2000 Chevrolet Blazer

1 Answer

Clutch wont engage after new install


Maybe the clutch master cylinder is not building hydraulic pressure? The internal seals in it may not be holding. Watch the slave cylinder push the clutch lever while someone presses the clutch pedal. If travel is not enough and was bled properly, you may need a new master cylinder.

Jul 07, 2013 | 1991 Chevrolet S-10

2 Answers

My clutch doesn't always disengage when the peddle is on the floor and when starting out in first bolts ahead as though the clutch was already part way out. I took it to a shop and they said my clutch...


your clutch master cylinder is right beside your brake master cylinder. I would advise you to replace the master cylinder and the slave cylinder together. The slave cylinder is on the side of the transmission. The slave cylinder does have a bleeder screw on it after the parts are bolted in place fill with dot 3 brake fluid and open the bleeder on the slave cylinder until fluid starts dripping out. Then tighten bleeder then open bleeder and have someone push down on clutch pedal while the pedal is pushed down tighten the bleeder the release pedal. Repeat this procedure until you get no air and the pedal feels normal and you should be good to go. Good luck!

Apr 14, 2011 | 1991 Toyota Celica

2 Answers

Clutch suddenly has no resistance and car won't shift gears. Fluids were low, have put fluid in the reservoir but still doesn't work. How do you bleed a clutch line?


on the transmission there is a slave cylinder that works like a brake cylinder, when you apply pressure to the clutch pedal a rod inside the vehicle under the dash pushes into a clutch master cylinder, (almost like a brake master cylinder without the reservoir, as the clutch master cylinder works off the brake master cylinders reservoir) the plunger in the clutch master cylinder applies fluid pressure to the slave cylinder,(located down on the trans near the clutch fork assembly) which projects a piston rod into the clutch fork dis-engaging the clutch. To bleed the clutch slave cylinder locate the bleeder screw on the slave cylinder,break loose so it loosens and tightens easily. Check fluid in brake master cylinder reservoir,fill if needed, while bleeder on the slave cyl is closed have a helper push clutch pedal to floor and back 7-8 times, (At first the clutch might stay at the floor, just pull it up by hand or foot and continue) after several pumps with no rest time push pedal to the floor and hold down with foot pressure, at this time loosen the bleeder on slave untill fluid leaks out, watch for air bubbles, close bleeder and repeat untill there is no sign of air bubbles, (make sure to check fluid in the brake master cylinder and keep fill as needed, do not let fluid get less than 1/2 empty as it might **** air and you will have to start over) If this does not bring clutch to operate then you need to check if slave cylinder is reachig its full extension of push rod or not. If it is not then you will have to replace the clutch master cyl or the clutch slave cyl or both as seals are bad and wont hold pressure. Or you need to inspect the clutch fork,the throw-out bearing, or the pressure plate fingers and clutch plate for failure or broken bent parts. I hope it turns out to be a easy fix on that clutching thing.

Jan 14, 2011 | 1995 Nissan Pickup

2 Answers

Clutch pedal doesnt engage gear


I believe is time for a new clutch buddy!!!

Feb 28, 2010 | 2002 Land Rover Freelander

2 Answers

UNABLE TO ENGAGE GEARS WHEN ENGINE RUNNING ( CAN ENGAGE GEARS WITH ENGINE OFF ). CLUTCH PEDAL GOES STRAIGHT TO THE FLOOR WHEN PRESSED


Need to have it check could be clutch master cylinder or slave cylinder or hose from clutch master cylinder to slave cylinder.check brake fluid at clutch master cylinder sit next to brake master cylinder if empty could have a leak. fill and pump peddle and look for leak.

Jan 12, 2010 | 2001 Ford Focus

1 Answer

No pressure clutch pedal goes straight to the floor 1988 holden r


If hydraulic actuated mechanism, loss of fluid, defective master cylinder or slave cylinder at the clutch. Missing pin or other part between slave cylinder and clutch arm. Loose or broken slave cylinder mounting. Missing pin or broken part between pedal and master cylinder. If mechanical linkage, look for broken components or missing pins at moving joints. If you tried to shift into gear with engine running, you may have damaged the transmission gears.

Aug 11, 2009 | 1993 Isuzu Rodeo

1 Answer

Clutch 1998 toyota tocoma


Replace master cylinder

Mar 11, 2017 | 1998 Toyota Tacoma

Not finding what you are looking for?
1994 Eagle Talon Logo

157 people viewed this question

Ask a Question

Usually answered in minutes!

Top Eagle Experts

yadayada
yadayada

Level 3 Expert

76132 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Stewart Dibbs

Level 2 Expert

308 Answers

Are you an Eagle Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...