Question about 1991 Lincoln Mark VII

1 Answer

How do I remove the starter bolts? This is for a 1991 lincoln mark 7 bill blass edition

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Lincoln Master
  • 1,075 Answers

Take a good look at the starter?it has two bolts whats the problem ????.adrian,,,

Posted on Aug 01, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I want to find red hoses for the radiator for bill blass 1990 mark vii


The only thing I have ever seen are metal hoses. They have a rubber sleeve that hose clamps on.
Earl's has some but I think they are stainless with colored ends.
You can try Summitracing.com or Americanstreetrod.com
May also search for these in Spectra brand.
The only time I have seen colored rubber hoses are blue ones and they are really silicon high pressure hoses (police cars use them)
Good luck on finding red hoses. I like red!

Aug 31, 2011 | 1990 Lincoln Mark VII

1 Answer

1988 lincoln mark 7 bill blass running rough. found bad injector on #7 and replaced. checked all plugs and wires, had engine cleaned for carbon. problem not as bad as before, but still a little rough. new...


TPS will make it run bad and worse as time goes by. Fuel regulator will not let it run or it will pour out black smoke on heavy acelleration. I would check all the vacuum lines first, this is the most likely cause of rough idle, besides a tune up. Vacuum leak....

Jun 10, 2011 | Lincoln Mark VII Cars & Trucks

2 Answers

How many bolts hold the starter in on a 1994 Mark VIII & where are they located?I removed 2 10mm bolts but it does not move


3 bolts.

Section 03-06: Starting System 1996 Mark VIII Workshop Manual
REMOVAL AND INSTALLATION Starter Motor Removal
  1. stc~us~en~file=ani_caut.gif~gen~ref.gif WARNING: WHEN SERVICING STARTER MOTOR (11002) OR PERFORMING ANY MAINTENANCE IN THE AREA OF THE STARTER MOTOR, NOTE THE HEAVY GAUGE INPUT LEAD CONNECTED TO THE STARTER SOLENOID (11390) IS HOT AT ALL TIMES. MAKE SURE THE PROTECTIVE CAP IS INSTALLED OVER THE TERMINAL AND IS REPLACED AFTER SERVICE.
    Disconnect the battery ground cable (14301). Refer to Section 14-01 .
  1. Raise the vehicle on a hoist. Refer to Section 00-02 .
  1. stc~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: When disconnecting hardshell connector at S-terminal, grasp the plastic shell and pull off. Do not pull on wire. Be careful to pull straight off to prevent damage to the connector and S-terminal. If any part of the connection is damaged, replace the damaged components.
    Disconnect starter cable and push-on connector from starter solenoid.
  1. Remove upper and middle bolts.
  1. Remove lower bolt and starter motor.

Mar 18, 2011 | 1994 Lincoln Mark VIII

2 Answers

1988 Lincoln Mark VII, Bill Blass, My abs system has seemed to stop working, doesnt want to allow the breaks to stay pumped up... when car is running brakes are gone completely... ive replaced the rotors,...


I have not heard of an ABS causing these problems. Usually, a loss of pressure is a hole in a brakeline or a bad master cylinder.

The first brakelines to leak on my 1988 Bill Blass where those going under the engine. Check in the frame where the lines are routed from the ABS to the front brakes.

I use a Vacuum Handpump Bleeder. As long as there is fluid in the Master, you should eliminate the air. If you have a leak when you draw down each wheel you may hear a whistling, deflating ballonlike sound of the air draw. My handpump has a gauge which will show a pressure drop.

Or you can go the other direction and disconnect the ABS lines to the wheels. When you draw the vacuum from the closed Calipers, there should be little air in the lines. However, a hole in the line will continue to drop the draw from that particular wheel Caliper. This would prove you have an opening in the line.

Oct 10, 2010 | 1991 Lincoln Mark VII

1 Answer

How do you get the top bolt off the starter


i used a 1/4" drive socket with long extension and ratchet. and leave the bottom bolt loose in place untill you get the top bolt out. (so it wont fall on you)

Aug 14, 2009 | 1991 Lincoln Mark VII

1 Answer

Trying to remove the starter on a 1991 SaturnSL


no there is not a special tool need more info go to collisionrepairadvice.com for more
1991 Saturn SL L4-1.9L DOHC VIN 7 Vehicle Level a_003366.gif Starting and Charging a_003366.gif Starting System a_003366.gif Starter Motor arrow1.gif Service and Repair arrow2.gif blnk_spc.gif Service and Repair Notes
  1. Disconnect battery ground cable.
  2. Remove air inlet tube and fresh air hose, on DOHC models, lift resonator upward to disengage from engine support bracket.
  3. Remove upper starter attaching bolt through access hole near intake manifold support bracket.
  4. Raise and support vehicle.
  5. Using suitable pliers, remove starter shield pin, then lift shield upward to release from solenoid.
  6. Disconnect starter electrical connectors and position aside.
  7. Remove lower starter attaching bolt.
  8. Remove rear starter support bracket attaching bolt.
  9. Rotate starter until bracket clears axle shaft support bracket, pull rearward toward lefthand side of vehicle to remove.
  10. Reverse procedure to install. Torque starter attaching bolts to 26 ft. lbs., starter bracket bolts to 22 ft. lbs. and starter solenoid terminal to 3 ft. lbs.

Apr 11, 2009 | 1991 Saturn SL1

1 Answer

I need to take the starter off of a 91 lincoln contintal


There is a second bolt that has to come off it is usually 180 degrees across from the 14 mm bolt. Once this is removed take off and disconnect any wire harnesses that are attatched to the starter. When you put the new one on be sure to disconnect the battery neg. pole first so you don'y blow the starter.
Good Luck

Nov 24, 2008 | 1991 Lincoln Continental

1 Answer

Mark lt starter


disconnect batt,remove the 3 starter mounting bolts and ground cable(should be connected to one of the mounting bolts),disconnect the 2 wires on the starter.install new starter and then reconnect batt.

Nov 02, 2008 | 2007 Lincoln Mark LT 4x2 5.5

Not finding what you are looking for?
1991 Lincoln Mark VII Logo

Related Topics:

174 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lincoln Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

fordexpert

Level 3 Expert

5520 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a Lincoln Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...