Question about 2000 Chrysler Town & Country

1 Answer

How to replace the upper radiator hose on a 2000 chrysler town and country van with a 3.3L engine.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 977 Answers

Undo the hose clamps on each end of the hose ,if they are spring type clampsyoumay need a pair of pliers or the like to remove them,then pull the hose off, if it is stuck you may need to try & twist it back & forth to break the seal,basically that is all you have to do,then fit the new hose & use new clamps if necessary.....hope this helps.....cheers

Posted on Aug 04, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2000 Chysler LHS Radiator drain won't drain


I had the drain plug changed out on my town and country van by the dealer for a total of $30 If you have loosened it and have not re-tightened it, don't drive it like that because sure as heck it will cut loose and you'll burn up an engine. Good luck

Dec 05, 2013 | 1998 Chrysler Cirrus

1 Answer

How to replace Thermostat on 2006 Town & Country Van ?


drain coolant system half way until coolant below thermostat.to locate thermostat follow upper radiator hose to engine.just remove both thermostat housing two bolts then clean all traces of old gasket material. be sure to have new thermostat gasket and gasket sealer on hand.make sure both thermostat housing and engine block clean dont have any traces of old gasket material if so you will have coolant leak.but besure to put gasket sealer both sides thermostat gasket just need thin layer RTV silicone.you can buy can of gasket remove to help remove old gasket material. try not to damage thermostat housing surface or engine surface with scraper deep scratches cuts in either surfaces will cause coolant leak be careful.

Dec 28, 2012 | Chrysler Cars & Trucks

2 Answers

Severe radiator leak 1998 Chrysler Town and Country LX


Could be your water pump.Let me know and I can give you a guide on how to replace.

Nov 26, 2012 | 1998 Chrysler Town & Country

1 Answer

Running hot


Remove thermostat and test it by dipping it in cold water ib an open pot. Heat the water on the stove while observing the thermostat. It shold opel just before the water boils. If it does check the radiator itself for clogging. Also fluch the engine water galleries.

Sep 27, 2012 | 2000 Chrysler Town & Country

1 Answer

Want to replace thermostat but cant find it


Follow the upper radiator hose from the radiator to the engine, it is inside the inlet on the engine side of the hose, you will need to remove the 2 13mm to access it.

Feb 05, 2011 | 2003 Chrysler Town & Country

1 Answer

I owne a 2005 Chrysler Towne & Country van with 3.8 liter V6 engine. The radiator has a small annoying leak in it. I am a good "shade tree" mechanic, but have never replaced this type of...


Its not that hard. Once you remove the upper radiator support everything will be a little more accessible. There will be two bolts that hold the a/c condenser to the radiator. Once those are removed pull up on the condenser to release it from the lower mounts and then let it rest in front of the radiator. Remove the fans from the radiator and the upper and lower hoses and the radiator will be ready to pull out.

It will take you about an hour to an hour and a half with a basic set of tools. Make sure you run the vehicle at idle with the cap off until it gets up to operating temp to get all the air out of the cooling system.

Dec 08, 2010 | 2005 Chrysler Town & Country

1 Answer

How do you install radiator on chrysler 2002 town and country


Caravan, Grand Voyager, Town and Country, Voyager, 2000-2004
Radiator - Removal & Installation
  1. Disconnect the negative battery cable.
    CAUTION Do not remove the radiator cap or drain with the cooling system hot and under pressure or serious personal injury can occur from hot pressurized coolant.
  2. Place a drain pan under the radiator drain. Open the radiator drain plug and allow the coolant to drain.
  3. Remove the air intake resonator from the air cleaner assembly.

    6521383.jpg
    Fig. Before removing the hood latch, mark its location on the crossmember with a paint marker or other tool

    10ccd56.jpg

    Fig. Once the hood latch is matchmarked, remove it from the crossmember (without disconnecting the cable) and set it aside
  4. Remove the Coolant Recovery System (CRS) overflow tank filler neck hose.
  5. Disconnect the cooling fan electrical connector located on the left side of the cooling fan module.
  6. Remove the CRS overflow tank mounting screw from the upper radiator crossmember.
  7. Remove the upper radiator-to-crossmember mounting screws.
  8. If equipped, disconnect the engine block heater wiring connector.
  9. Remove the upper radiator crossmember.

    a267e07.jpg
    Fig. Remove the grill extension...


    931f3b8.jpg

    Fig. ...and the upper radiator-to-crossmember bolts, then . . .


    9eec6fc.jpg
    Fig. ...unbolt the crossmember . . .


    f878ac0.jpg
    Fig. ...and lift it from the front of the vehicle
  10. Remove the entire air cleaner assembly.
  11. Disconnect and plug the automatic transaxle oil cooler lines from the radiator.
  12. Disconnect the upper and lower radiator hoses from the radiator. Remove the lower radiator hose clip from the cooling fan module.
  13. Remove the A/C condenser mounting fasteners and separate the A/C condenser from the radiator. Be sure the condenser is supported in position.
  14. Remove the A/C filter/drier mounting bracket, 2 mounting bolts to the cooling fan module and 2 mounting nuts to the filter/drier. Remove the mounting bracket.
  15. Carefully lift the radiator out of the engine compartment. Be careful not to damage the radiator cooling fins or water tubes during removal.

continue...

Mar 27, 2010 | 2002 Chrysler Town & Country

1 Answer

How do I change the thermostat on 2002 Chrysler Town & Country


Follow the upper radiator hose towards the engine. Remove the hose and the 2 13mm bolts - there is your thermostat and gasket.

Oct 22, 2009 | 2002 Chrysler Town & Country

Not finding what you are looking for?
2000 Chrysler Town & Country Logo

278 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8548 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...