Question about 2004 Nissan Sentra

Open Question

2004 nissan sentra 1.8 cam torque specifications

Posted by on


6 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

  • 146 Answers

SOURCE: torque settings for cylinder head nissan sentra

Tighten in sequence to 29ft.lbs then tighten in sequence to 58ft lbs. then loosen all bolts. Then tighten in sequence to 33ft lbs. then tighten each bolt in sequence 90 degrees then tighten each bolt again 90 degrees

Posted on Jul 26, 2009

  • 8 Answers

SOURCE: engine head torque settings for 2005 nissan sentra 1.8

email me ill send you it via email cant post here too bigg!!

Posted on May 29, 2009

  • 3092 Answers

SOURCE: Need to know where the Cam shaft sensor is located

Camshaft sensor located on front of engine over by the drive belts end just below the valve cover on the cylinder head just to the right of the center of the cylinder head, will have a connector with three wire's, remove 10mm bolt and slide right out install new one and your done.Good luck.

Posted on Mar 25, 2010

  • 4 Answers

SOURCE: torque specifications for a 2004 nissan sentra ser

180 lb-ft @ 4000 rpm

Posted on May 09, 2010

  • 906 Answers

SOURCE: 2004 Sentra: How you change transmission Fluid in Nissan Sentra...

good day Sir, try this link i hope this will help you.

nissan sentra2003

Posted on Jul 30, 2010

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

What torque pressure should i tighten the cams on a 2004 nissan sentra 1.8 lt engine

If you are in this deep you really should have a shop manual, which will give this information and so much more.

May 09, 2016 | Nissan Cars & Trucks

2 Answers

Two codes coming up on car even after fixing alot on car now need to figure out low cost ways to fix P0744 & P0722 code issues spent 1,800 on car & have spent 1,400 already in parts & labor.

you need a better mechanic that traces ALL of the possibilities of each code, not just read the code and trow in a part hoping that it's fixed ~ it can be wiring as well, not just plug in a new part as mentioned on the 2nd trouble code to the vehicle speed sensor

P0744 Torque Converter Clutch Circuit Intermittent

P0722 Output Speed Sensor No Signal

the first of the 2 looks to be more intensive to trace and find out the problem & the 0722 is the easier job for an intermediate mechanic to trace the wiring for continuity

Apr 20, 2015 | Cars & Trucks

1 Answer


on a 4 cyl is very easy, Nissan recommends replacement of both the crank and cam sensor together, but the crank sensor is in the back of the engine, near the transmission bell housing under the engine mount bracket. the cam sensor is in the back of the cylinder head and both have 1 bolt each, 10mm.

Nov 06, 2014 | 2004 Nissan Sentra

1 Answer


for the head or what , be a little more specific on your question everything gets torqued on a motor

Aug 15, 2014 | 1997 Nissan Sentra

1 Answer

What is cylinderhead bolts torque settings

follow this link and click on torque tables then look up your vehicle

Jul 22, 2014 | Nissan Sentra Cars & Trucks

1 Answer

Need engine head torque settings for 2005 nissan sentra 2.5

Can be found in the Haynes repair manual, available at an auto parts store for appx $25.00.

Jun 07, 2012 | 2004 Nissan Sentra

1 Answer

How do you set the timing on a 94 Nissan Sentra?

There is 3 marks on the timing chain, 2 are exactly 16 links apart and the other is 22 from either of the 2. The engine should be at top dead center. Line the 2 (16 apart) marks with marks on your cam gears and the 3rd with your crank gear. Torque cam bearings to 100 inch lbs.

Feb 03, 2010 | 1994 Nissan Sentra 4-Door

1 Answer

2006 nissan sentra drive belt install i can not figer out how to install both belts and what the tq is for the two bolts

keep trying and it will come ,as for the torque then just tight with a 3/8 drive socket set will suffice ,been fixing motors for 40yrs and never use a torque wrench,have one in case a customer is around ------

Jan 15, 2010 | 2004 Nissan Sentra

Not finding what you are looking for?
2004 Nissan Sentra Logo

Related Topics:

506 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts


Level 3 Expert

81400 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides