Question about Mazda B2200

1 Answer

Exactly which bolts do I remove to remove the fr. brake caliper on my '90 Mazda B2200 (pickup) with 2 Wh Drive ? and how do I remove the caliper so I can get at the wheel bearings?

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

    Governor:

    An expert whose answer got voted for 20 times.

  • Expert
  • 170 Answers

If you look at the assembly you will see 2 bolts covered in rubber boots. those hold the brake pads in place and connect to the frame of the brake caliper. the other two connect the caliper frame to the truck hub . this all needs to come off to do what you suggest

Posted on Jul 31, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I remove front brake caliper on 1996 mazda 626


if you are just changing the pads there are 2 bolts that split the caliper in halve and allow you to change the pads thres two bolts are located top and bottom on the backside of the caliper and require an allen wrench for removal to remove the whole caliper there are 2 bolts on the back side closer to the center top and bottom that require a 17mm socket remove these 2 bolts clamp off the flex brake hose with a clamp and remove from caliper and work up and down until caliper comes away from disc

Nov 30, 2010 | 1996 Mazda 626

1 Answer

How to change front disc brake pads on 2000 Mazda Bravo B2500


jack up car, remove the road wheels, at the rear of the caliper you will have 2 or 3 bolts holding the caliper onto the stub axle, remove the bolts and remove the caliper, remove the outer pad, leave the inner pad in place and use a "G" clamp to compress the brake piston until it has bottomed, if this is not done the new pads will not fit back over the rotor as the piston is too far out and the new pads are thicker than the old ones.
place the new pads in the caliper and fit over the rotor, replace the 2 or 3 bolts that hold the caliper in place, replace the road wheel, tighten the nuts and lower the car to the ground, pump the brake pedal to see if you have brakes, if you do have brakes take it for a test drive away from any traffic if possible

Jun 13, 2010 | 1988 Mazda B2600 Cab Plus

1 Answer

How do I replace the front brake pads on my 2009 Mazda 6 2 litre? Can I do it myself?


Step 1 Park the Mazda 6 on a flat surface. Put the emergency brake on and put wedges behind the wheels to prevent the vehicle from rolling. Disconnect the negative battery cable. Using a syringe, turkey baster or similar tool, drain two thirds of the brake fluid from the master cylinder. Remove the wheel.
  • Step 2 Remove the bolts attached to the brake pipe. Remove the bolt cap attached to the caliper top. Swing the caliper, pivoting it downwards. Suspend the caliper from the frame using mechanics wire. Remove the M-springs, the pads and the shims.
  • Step 3 Press the caliper pistons back into the cylinders. Install the brake pads. Lubricate the exterior of the pads using anti-squeal. Install the shims. Install the M-Springs. Reinstall the caliper. Using a torque wrench torque the bolt to 36 to 39-ft. lbs. Install the cap.
  • Step 4 Reinstall the wheels. Add brake fluid to the master cylinder. Bleed the brakes. Reconnect the negative battery cable to the battery. Start the engine and pump the brakes 3 to 4 times to seat the brake pads. Test drive the Mazda 6 at slow to moderate speeds to ensure that the maintenance was performed correctly.I hope this helps you and please have a merry xmas
  • Dec 18, 2009 | 2009 Mazda MAZDA6

    1 Answer

    How do I get the front rotors off to replace new ones.


    jack up.take wheels off.turn steering right on caliper undo bracket slide bolt 2 of them them undo caliper bracket 2 more bolts move caliper and hang to left take take rotor off.thats for 4wheel drive.2 wheel with bearing.take bearing cap off take out cotter pin and lock washer off.pull rotor.suggestion new wheel bearings.and brakes.ps old school trick take fluid cap off.put flat head between pad n rotor pry back before taking caliper to recess the calipr.then remove brakes.then big water pump pliers and recess caliper fully.it will over flow the resovoir.no biggy brake cleaner off this will help.sometime bleeder valves brake off then cause you more aggrivation like buying new calipers.pss make sure yuo grease new bearings well and also caliper slides.hope this helps

    Nov 25, 2009 | Mazda B2200 Cars & Trucks

    1 Answer

    Silverado 1500 Z71 off road, 5.3L. Details on fr


    This is for the front: Removal & Installation
    1. Remove 2/3 of the brake fluid from the master cylinder.
    2. Remove or disconnect the following:
      • Wheel
      • Caliper. Suspend the caliper from the frame with mechanic's wire. Do not allow the caliper to hang from the brake hose.
      • Caliper mounting bracket bolts
      • Caliper mounting bracket from the steering knuckle assembly
      • Brake pads from the caliper mounting bracket
      • Clips from the inside ends of the caliper mounting bracket and discard
    To install:
    1. Install or connect the following:
      • Clips to the inside ends of the caliper mounting bracket
      • Brake pads to the caliper mounting bracket
      • Inner pad (1 wear indicator)
      • Outer pad (2 wear indicators)
      • Caliper mounting bracket to the steering knuckle assembly
    2. Perform the following procedure before installing the caliper mounting bracket bolts:
      • Remove all traces of the original adhesive patch.
      • Clean the threads of the bolt with brake parts cleaner or the equivalent and allow to dry.
      • Apply red Loctite®272 to the threads of the bolt.
    3. Install or connect the following:
      • Caliper mounting bracket bolts to the steering knuckle. Tighten the caliper guide pin bolts to 74 ft. lbs. (100 Nm) on 15 series or 80 ft. lbs. (108 Nm) on 25/35 series.
      • Caliper
      • Tire and wheel assembly
    4. Refill the master cylinder to the proper level with fresh brake fluid. Pump the brake pedal slowly and firmly in order to seat the brake pads. Burnish the brakes as needed.

    Oct 12, 2009 | 2003 Chevrolet Silverado 1500

    1 Answer

    86 Toyota P/U disc brakes, 2 wheel drive..what


    You need to use a large "C Clamp" to compress the caliper piston back into the cylinder. This is the normal way since there is no "return" mechanism other than "lack of hydraulic pressure".
    The brake fluid will back up into the master cylinder reservoir, so remove some of the fluid.
    Just two bolts hold the floating caliper in place.

    Oct 01, 2009 | 1986 Toyota Pickup 4WD

    1 Answer

    How do i change both front and rear brake pads on a 2004 mazda rx8?


    CHANGING FRONT BRAKE PADS
    Jack up the car. Take off your tire. Find the bolt on the back of the caliper and take it off. This should release the caliper, pull the caliper off the disc. Now you should be able to take the pad out. Replace the pad. You'll need a special tool to reset the caliper. As the brakes wear down, the caliper gets tighter so the brakes still work. I'm not sure exactly what its called, but you can borrow one from auto zone. Follow the instructions that come with it to reset the caliper. Slide the caliper back over the disc. If it doesn't go on, you need to reset the caliper more. Put the relese bolt back in. Put your tire back on.Drive slowly and test the brakes.
    CHANGING THE REAR BRAKE PADS
    The rear brakes on the rx8 are a bit different than most setups...be careful! The only way to move the piston back into the caliper is by way of a special allen head bolt that is directly behind the piston, on the back side of the caliper, installed under a 14mm bolt.
    You have to remove this bolt to gain access to the allen head. As you loosen the allen head bolt(counter-clockwise), the piston will move back into the caliper.
    Installation is pretty typical, again, the allen head bolt being the unusual part. The manual says to tighten this bolt until the pads contact the rotor, then loosen the bolt 1/3rd of a turn, then reinstall the 14mm bolt.

    Sep 04, 2009 | 2005 Mazda RX-8

    1 Answer

    My 90 b2200 has been parked for a while...i had it aligned 5k mi ago before driving it cross country...not it pulls to the right rather hard, and when start to move it seems like the brake is still on..i...


    sounds like you have a frozen brake caliper, lift right wheel off ground and remove tire, try to spin disk if you cannot then u need to remove caliper try using a c-clamp and compress inner pad and see if piston will move inward if yes check for leak and clean retry and if still doesn't work or cannot move piston in replace caliper. It most likely has rusted and seized from long term sitting.

    Jul 16, 2009 | 1988 Mazda B2200

    2 Answers

    How to change out front brake pads on a 2001 mazda 626?


    remove 2 caliper bolts, remove old pads. put new pads in there place, before installing the caliper, be sure to squeeze the piston back in the caliper otherwise it will not fit back over the new pads. than replace the caliper and the 2 mounting bolts.

    May 07, 2009 | 1995 Mazda 626

    1 Answer

    Igniton switch installation


    Remove column cover, remove wiring harness, cut a slot in 2 bolts (originally breaw away bolts) holding swith assembly to steering column ??? remove put in new one

    Dec 24, 2008 | 1988 Mazda B2200

    Not finding what you are looking for?
    Cars & Trucks Logo

    Related Topics:

    97 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Mazda Experts

    yadayada
    yadayada

    Level 3 Expert

    76132 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22156 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    8273 Answers

    Are you a Mazda Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...